Temperature control by simulated adaptive layer times in powder bed fusion processes Christoph BehrensNiklas OstermannVasily Ploshikhin Full Research Article Open access 25 May 2024
PBF-LB of large-area magnesium WE43 structures surface-enhanced by plasma electrolytic oxidation Arvid AbelAnutsek SharmaStefan Kaierle Full Research Article Open access 24 May 2024
β-Modification in heterogeneous polypropylene for laser-based powder bed fusion of polymers Simon CholewaThomas ForstnerDietmar Drummer Full Research Article Open access 23 May 2024
Knowing the spectral directional emissivity of 316L and AlSi10Mg PBF-LB/M surfaces: gamechanger for quantitative in situ monitoring Tina BeckerThomas StarkSimon J. Altenburg Full Research Article Open access 23 May 2024
Enhancing mechanical and morphological properties of glass fiber reinforced epoxy polymer composites through rutile nanoparticle incorporation K. P. Srinivasa PerumalL. SelvarajanShailesh Shriguppikar Full Research Article 23 May 2024
Investigation of additively manufactured lattice structures for refractive optical systems based on auxetic properties Johannes FraschHenrik von LukowiczStefan Risse Full Research Article Open access 21 May 2024
Fatigue behavior of 4D printed materials: a review Md Jarir Hossain Review Article Open access 21 May 2024
Influence of wax addition on feedstock processing behavior in additive manufacturing of metals by material extrusion Thomas ForstnerSimon CholewaDietmar Drummer Full Research Article Open access 21 May 2024
Camera-based measurement and control of the contact tip to work distance in wire arc additive manufacturing Moritz BaldaufPhilipp LohrerJohannes H. Schleifenbaum Full Research Article 21 May 2024
Design and implementation of a machine log for PBF-LB/M on basis of IoT communication architectures and an ETL pipeline Konstantin PokaSozol AliKai Hilgenberg Full Research Article Open access 21 May 2024
Zr-based bulk metallic glasses in PBF-LB/M: near-polished surface quality in the as-built state Jan WegnerLars BruckhausStefan Kleszczynski Full Research Article Open access 18 May 2024
Empirical calibration method for the thermal simulation of Cu47Ti34Zr11Ni8 single tracks in laser powder bed fusion Lars BruckhausJan WegnerStefan Kleszczynski Full Research Article Open access 18 May 2024
Cradle-to-gate life cycle assessment: a comparison of polymer and metal-based powder bed fusion for the production of a robot end-effector with internal conformal channels Talha AnwarA. C. LopesA. J. Pontes Full Research Article 18 May 2024
Efficient utilization of remelt strategy for improving relative density and surface integrity to eliminate necessity of performing post-processing of additively manufactured 316L stainless steel Sajjad RajabiAlireza KhodabandehMohammad Reza Razfar Full Research Article 18 May 2024
Geometry-induced process and part characteristics in support-free powder bed fusion of polypropylene at room temperature Samuel SchlichtDietmar Drummer Full Research Article Open access 17 May 2024
Sintering of 3D-printed aluminum specimens from the slurry-based binder jetting process Jan AngenoorthPatricia ErhardDaniel Günther Full Research Article Open access 17 May 2024
Exploring the environmental benefits of 3D printing technology in concrete construction; a review Rania Abdelrahim MohamedAbdelaziz Farouk A. Mohamed Review Article 17 May 2024
Optimizing energy modeling in PBF-LB/M metal additive manufacturing: a detailed analysis of resource and energy demand based on standard tensile test specimen Joachim BrinkmannJan C. AurichHenrik te Heesen Full Research Article Open access 16 May 2024
Degradation characteristics of 3D printed continuous fibre-reinforced PA6/chopped fibre composites in simulated saltwater Pouyan GhabeziTomas FlanaganNoel M. Harrison Full Research Article Open access 16 May 2024
Numerical study of powder flow characteristics of coaxial nozzle direct energy deposition at different operating and design conditions Yogesh NogdheAnant Kumar RaiM. Manjaiah Full Research Article 16 May 2024
A comparative analysis of printing parameter effects of tensile and flexural specimens produced with two different printers by the TAGUCHI method Sermet DemirCaner Yüksel Full Research Article 16 May 2024
Correction: In-process closed-loop control for stabilising the melt pool temperature in selective laser melting Volker RenkenAxel von FreybergAndreas Fischer Correction Open access 15 May 2024
3D concrete printing success: an exhaustive diagnosis and failure modes analysis Fatima Zahra OulkhirIatimad AkhrifMostapha El Jai Review Article 15 May 2024
Additive manufacturing of carbon-martensitic hardening ledeburitic cold work tool steels using Fused Filament Fabrication and subsequent Supersolidus Liquid-Phase Sintering A. RöttgerL. WieczorekM. Löwer Full Research Article Open access 14 May 2024
Experimental study on the effect of filament-extrusion rate on the structural, mechanical and thermal properties of material extrusion 3D-printed polylactic acid (PLA) products László LendvaiImre FeketeAlessandro Pegoretti Full Research Article Open access 12 May 2024
Surface finish enhancement in fused deposition modeling of PLA using chloroform: a comprehensive characterization study Ali Akhavan FaridTshai Kim YeowKamesh Krishnamurariu Full Research Article 12 May 2024
Analysis of phase, microstructure, and mechanical characteristics of selective laser melted AlSi10Mg alloy after post-heat treatment B. Sai CharanM. SrikanthDeepak K. Pattanayak Full Research Article 10 May 2024
Numerical simulation and experimental investigation of temperature distribution during the wire arc additive manufacturing (WAAM) process Deepak Kumar GuptaRahul S. Mulik Full Research Article 09 May 2024
Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing Björn RingelDavid SchwarzMatthias Oechsner Correction Open access 08 May 2024
The effect of hot isostatic pressing pressure level and solution annealing cooling rate on CM247 LC nickel-based superalloy processed by laser-based powder bed fusion P. A. MartelliE. BassiniD. Ugues Full Research Article Open access 08 May 2024
The effect of interface enhancement on the mechanical properties of fibre-reinforced PA6 matrix composites in material extrusion-based additive manufacturing Alperen DoğruMehmet Özgür SeydibeyoğluCagri Ayranci Full Research Article 07 May 2024
In situ build surface topography determination in electron beam powder bed fusion Jakob RennerMatthias MarklCarolin Körner Full Research Article Open access 07 May 2024
Improving a tool-path optimisation method in material extrusion additive manufacturing by data clustering and collapsing N. VolpatoT. R. WellerF. C. Becheli Full Research Article 06 May 2024
Effect of a process interruption on the mechanical properties of AlSi10Mg components produced by laser powder bed fusion (PBF-LB/M) M. MoserS. BrennerV. Nedeljkovic-Groha Full Research Article Open access 06 May 2024
Prediction of the penetration depth of particle-loaded inks in binder jetting Maja LehmannCara G. KolbMichael F. Zaeh Full Research Article Open access 06 May 2024
Investigating the reversible performance of shape memory composites in 4D printing using magnetic field stimulation: case study of polylactic acid/SrFe12O19 composite filament Seyed Mohammad Reza SotoudehMilad Sadegh YazdiMohammad Hassanpour Full Research Article 05 May 2024
Influence of process parameters on the occurrence of defects and dimensional properties of green part produced by material extrusion of highly filled polymer Raphaël CôtéDorian DelbergueJérémie Soulestin Full Research Article 03 May 2024
Energy absorption of multi-scale hierarchically graded auxetic structures: experimental and simulation methods A. R. MortezapourA. Hosseini MonazzahM. Sameezadeh Full Research Article 02 May 2024
Laser powder bed fusion processing of UNS C63020 nickel aluminum bronze powder A. J. RaynerJ. HierlihyD. P. Bishop Full Research Article 02 May 2024
Fused granulate fabrication of injection molding inserts from high-performance ULTEM 9085™ thermoplastic for cosmetic packaging industry Albert CurmiArif Rochman Full Research Article Open access 01 May 2024
Strain sensing characteristics of 3D-printed carbon nanotubes/polypyrrole/UV-curable composites: experimental validation and machine learning predictions Nutthapong PoompiewWiwittawin SukmasPranut Potiyaraj Full Research Article 01 May 2024
Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing Björn RingelDavid SchwarzMatthias Oechsner Correction Open access 29 April 2024
Investigation of the effects of volume fraction, aspect ratio and type of fibres on the mechanical properties of short fibre reinforced 3D printed composite materials Hassan GonabadiYao ChenSteve Bull Full Research Article Open access 29 April 2024
Benchmark study of melt pool and keyhole dynamics, laser absorptance, and porosity in additive manufacturing of Ti-6Al-4V Arash SamaeiJoseph P. LeonorGregory J. Wagner Full Research Article 29 April 2024
Strength evaluation of polymer ceramic composites: a comparative study between injection molding and fused filament fabrication techniques Lovin K. JohnM. RamuNandhu Binudas Full Research Article 27 April 2024
Integrating resistance-based sensing into fused filament fabricated mechanical metamaterial structure Imran KhanMuhammad YaseenFatima Hira Full Research Article 26 April 2024
Process parameter optimization of pulsed laser deposition of hydroxyapatite coated polymer implant for better surface roughness and cell viability K. HariharanN. SathishkumarG. Arumaikkannu Full Research Article 26 April 2024
Microstructure and tribological properties of solid lubricant-doped CMT-WAAMed Stellite deposits Jari TuominenAli SabrPasi Peura Full Research Article Open access 22 April 2024
Definitive screening design for mechanical properties enhancement in extrusion-based additive manufacturing of carbon fiber-reinforced PLA composite Muhammad AbasTufail HabibSahar Noor Full Research Article 21 April 2024
Additive manufacturing for producing microchannel heat sinks A. N. KivananiS. KhalilpourazaryF. Mobadersani Review Article 21 April 2024