Abstract
Ceramic matrix composites containing fiber reinforcements possess superior mechanical and tribological properties, as compared to their monolithic counterparts, that render them better suited for engineering applications demanding high strength, wear resistance, and resistance to thermal shock. Among the wide range of reinforcements used for toughening the otherwise intrinsically brittle bulk ceramic materials, carbon nanotubes (CNTs), owing to their excellent physical, mechanical, and thermal properties, are considered to be one of the most promising reinforcement types. The exceptional mechanical properties of CNTs offer excellent opportunities toward the development of considerably stronger and tougher ceramic nanocomposite systems for potential applications in aircraft and aerospace industries. However, there are many challenges with respect to the processing of CNT-reinforced bulk ceramic materials that limit their commercial applications to considerable extent. Additionally, dispersion of the CNTs, optimization of the CNT volume fractions, development of suitable CNT/matrix interfaces, and distribution within the sintered polycrystalline ceramic microstructures are some of the aspects that need particular attention. Continuing research efforts have been directed toward addressing issues related to such aspects, in a bid to attain best possible combination of mechanical and tribological properties. With regard to microstructure development, achieving uniform distribution of well-dispersed CNTs within the sintered polycrystalline ceramic matrix (i.e., reinforcing the grain interiors and not just the grain boundaries with CNTs) has been found to be particularly difficult, until very recently. In these contexts, after discussing some of the basic aspects of carbon nanotubes and ceramic-CNT composites, the present chapter provides a comprehensive review of the overall status of research and development in CNT-reinforced ceramic matrix composites, with particular emphasis on a variety of processing techniques investigated to date in a bid to optimize the quality of CNT dispersion, character of the CNT-matrix interfaces, eventual densification of the composites, and also cost-effectiveness. The influences of CNT reinforcements on the properties of the some of the important ceramic systems for advanced structural applications are discussed, with an emphasis toward fracture behavior and the possible toughening mechanisms. This review also highlights the more recent research efforts that have been conducted to address the issues concerning inhomogeneous dispersion and distribution of CNTs within the ceramic matrix, thus aiming toward the realization of the full potential of CNTs as reinforcing fibers. Lastly, the various potential applications for ceramic-CNT composites as structural materials have been highlighted, with an outlook toward the scope for future developments and issues that need to be further addressed.
References
Crivelli-Visconti I, Cooper GA (1969) Mechanical properties of a new carbon fibre material. Nature 221:754–755
Marshall DB, Evans AG (1985) Failure mechanisms in ceramic-fiber/ceramic-matrix composites. J Am Ceram Soc 68:225–231
Sternitzke M (1997) Structural ceramic nanocomposites. J Eur Ceram Soc 17:1061–1082
Mukhopadhyay A, Basu B (2007) Consolidation–microstructure–property relationships in bulk nanoceramics and ceramic nanocomposites: a review. Int Mater Rev 52:257–288
Awaji H, Choi SM, Yagi E (2002) Mechanisms of toughening and strengthening in ceramic-based nanocomposites. Mech Mater 34:411–422
Brennan JJ, Prewo KM (1982) Silicon carbide fibre reinforced glass-ceramic matrix composites exhibiting high strength and toughness. J Mater Sci 17:2371–2383
Levi CG, Yang JY, Dalgleish BJ, Zok FW, Evans AG (1998) Processing and performance of an all-oxide ceramic composite. J Am Ceram Soc 81:2077–2086
Dassios KG (2007) A review of the pull-out mechanism in the fracture of brittle-matrix fibre-reinforced composites. Adv Compos Lett 16:17–24
Klug T, Bruckner R (1994) Preparation of C-fibre borosilicate glass composites: influence of the fibre type on mechanical properties. J Mater Sci 29:4013–4021
Beyerle DS, Spearing SM, Zok FW, Evans AG (1992) Damage and failure in unidirectional ceramic-matrix composites. J Am Ceram Soc 75:2719–2725
Evans AG, Zok FW (1994) The physics and mechanics of fibre-reinforced brittle matrix composites. J Mater Sci 29:3857–3896
Davidge RW, Green TJ (1968) The strength of two-phase ceramic/glass materials. J Mater Sci 3:629–634
Niihara K (1991) New design concept of structural ceramics. J Ceram Soc Jpn 99:974–982
Iijima S (1991) Helical microtubules of graphitic carbon. Nature 354:56–58
Treacy MMJ, Ebbesen TW, Gibson JM (1996) Exceptionally high Young’s modulus observed for individual carbon nanotubes. Nature 381:678–680
Yu MF, Lourie O, Dyer MJ, Moloni K, Kelly TF, Ruoff RS (2000) Strength and breaking mechanism of multiwalled carbon nanotubes under tensile load. Science 287:637–640
Iijima S, Ichihashi T (1993) Single-shell carbon nanotubes of 1-nm diameter. Nature 363:603–605
Zheng LX, O’Connell MJ, Doorn SK, Liao XZ, Zhao YH, Akhadov EA, Hoffbauer MA, Roop BJ, Jia QX, Dye RC, Peterson DE, Huang SM, Liu J, Zhu YT (2004) Ultralong single-wall carbon nanotubes. Nat Mater 3:673–676
Cho J, Boccaccini AR, Shaffer MSP (2009) Ceramic matrix composites containing carbon nanotubes. J Mater Sci 44:1934–1951
Wang X, Padture NP, Tanaka H (2004) Contact-damage-resistant ceramic/single-wall carbon nanotubes and ceramic/graphite composites. Nat Mater 3:539–544
Zhan GD, Kuntz JD, Wan J, Mukherjee AK (2003) Single-wall carbon nanotubes as attractive toughening agents in alumina-based nanocomposites. Nat Mater 2:38–42
Harris PJF (2004) Carbon nanotube composites. Int Mater Rev 49:31–43
Lu KL, Lago RM, Chen YK, Green MLH, Harris PJF, Tsang SC (1996) Mechanical damage of carbon nanotubes by ultrasound. Carbon 34:814–816
Niyogi S, Hamon MA, Perea DE, Kang CB, Zhao B, Pal SK, Wyant AE, Itkis ME, Haddon RC (2003) Ultrasonic dispersions of single-walled carbon nanotubes. J Phys Chem B 107: 8799–8804
Monthioux M, Smith BW, Burteaux B, Claye A, Fischer JE, Luzzi DE (2001) Sensitivity of single-wall carbon nanotubes to chemical processing: an electron microscopy investigation. Carbon 39:1251–1272
Galaveen SC, Satam MK, Gurnani L, Venkateswaran T, Mukhopadhyay A (2016) Facile-low temperature route towards development of SiC-based coating on carbon nanotubes for improved oxidation resistance. J Mater Sci 51:8543–8549
Curtin WA, Sheldon BW (2004) CNT-reinforced ceramics and metals. Mater Today 7:44–49
Thostenson ET, Ren Z, Chou TW (2001) Advances in the science and technology of carbon nanotubes and their composites: a review. Compos Sci Technol 61:1899–1912
Shigeta M, Komatsu M, Nakashima N (2006) Individual solubilization of single-walled carbon nanotubes using totally aromatic polyimide. Chem Phys Lett 418:115–118
Star A, Stoddart JF (2002) Dispersion and solubilization of single-walled carbon nanotubes with a hyperbranched polymer. Macromolecules 35:7516–7520
Zhu J, Yudasaka M, Zhang M, Iijima S (2004) Dispersing carbon nanotubes in water: a noncovalent and nonorganic way. J Phys Chem B 108:11317–11320
Paredes JI, Burghard M (2004) Dispersions of individual single-walled carbon nanotubes of high length. Langmuir 20:5149–5152
Shaffer MSP, Fan X, Windle AH (1998) Dispersion and packing of carbon nanotubes. Carbon 36:1603–1612
Perepichka DF, Wudl F, Wilson SR, Schuster DI (2004) The dissolution of carbon nanotubes in aniline, revisited. J Mater Chem 14:2749–2752
Muller TJJ, Bunz UHF (2007) Functional organic materials: syntheses, strategies and applications. Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim
Mukhopadhyay A (2009) Fabrication and properties of oxide nanocomposites containing uniformly dispersed second phases. PhD thesis, University of Oxford, Oxford, UK
Vasiliev AL, Poyato R, Padture NP (2007) Single-wall carbon nanotubes at ceramic grain boundaries. Scr Mater 56:461–463
Wei T, Fan Z, Luo G, Wei F (2008) A new structure for multi-walled carbon nanotubes reinforced alumina nanocomposite with high strength and toughness. Mater Lett 62:641–644
Satam MK, Gurnani L, Vishwanathe S, Mukhopadhyay A (2016) Development of carbon nanotube reinforced bulk polycrystalline ceramics with intragranular carbon nanotube reinforcement. J Am Ceram Soc 99:2905–2908
Estili M, Kawasaki A (2008) An approach to mass-producing individually alumina-decorated multi-walled carbon nanotubes with optimized and controlled compositions. Scr Mater 58: 906–909
Estili M, Kawasaki A, Sakamoto H, Mekuchi Y, Kuno M, Tsukada T (2008) The homogeneous dispersion of surfactantless, slightly disordered, crystalline, multiwalled carbon nanotubes in α-alumina ceramics for structural reinforcement. Acta Mater 56:4070–4079
Chu BTT, Tobias G, Salzmann CG, Ballesteros B, Grobert N, Todd RI, Green ML (2008) Fabrication of carbon-nanotube-reinforced glass–ceramic nanocomposites by ultrasonic in situ sol–gel processing. J Mater Chem 18:5344
Mukhopadhyay A, Chu BTT, Green MLH, Todd RI (2010) Understanding the mechanical reinforcement of uniformly dispersed multiwalled carbon nanotubes in alumino-borosilicate glass ceramic. Acta Mater 58:2685–2697
Boccaccini AR, Acevedo DR, Brusatin G, Colombo P (2005) Borosilicate glass matrix composites containing multi-wall carbon nanotubes. J Eur Ceram Soc 25:1515–1523
Boccaccini AR, Thomas BJC, Brusatin G, Colombo P (2007) Mechanical and electrical properties of hot-pressed borosilicate glass matrix composites containing multi-wall carbon nanotubes. J Mater Sci 42:2030–2036
Chintapalli RK, Marro FG, Milsom B, Reece M, Anglada M (2012) Processing and characterization of high-density zirconia-carbon nanotube composites. Mater Sci Eng A 549:50–59
Ning J, Zhang J, Pan Y, Guo J (2003) Fabrication and mechanical properties of SiO2 matrix composites reinforced by carbon nanotube. Mater Sci Eng A 357:392–396
Peigney A, Laurent C, Dobigeon F, Rousset A (1997) Carbon nanotubes grown in situ by a novel catalytic method. J Mater Res 12:613–615
Peigney A, Laurent C, Dumortier O, Rousset A (1998) Carbon nanotubes–Fe–alumina nanocomposites. Part I: influence of the Fe content on the synthesis of powders. J Eur Ceram Soc 18:1995–2004
Laurent C, Peigney A, Dumortier O, Rousset A (1998) Carbon nanotubes-Fe-alumina nanocomposites. Part II: microstructure and mechanical properties of the hot-pressed composites. J Eur Ceram Soc 18:2005–2013
Flahaut E, Peigney A, Laurent C, Marlière C, Chastel F, Rousset A (2000) Carbon nanotube-metal-oxide nanocomposites: microstructure, electrical conductivity and mechanical properties. Acta Mater 48:3803–3812
Peigney A, Laurent C, Flahaut E, Rousset A (2000) Carbon nanotubes in novel ceramic matrix nanocomposites. Ceram Int 26:677–683
Peigney A, Flahaut E, Laurent C, Chastel F, Rousset A (2002) Aligned carbon nanotubes in ceramic-matrix nanocomposites prepared by high-temperature extrusion. Chem Phys Lett 352:20–25
Peigney A (2003) Composite materials: tougher ceramics with nanotubes. Nat Mater 2:15–16
Xia Z, Riester L, Curtin WA, Li H, Sheldon BW, Liang J, Chang B, Xu JM (2004) Direct observation of toughening mechanisms in carbon nanotube ceramic matrix composites. Acta Mater 52:931–944
Xia Z, Curtin WA, Sheldon BW (2004) Fracture toughness of highly ordered carbon nanotube/alumina nanocomposites. J Eng Mater Technol 126:238
Xia ZH, Lou J, Curtin WA (2008) A multiscale experiment on the tribological behavior of aligned carbon nanotube/ceramic composites. Scr Mater 58:223–226
Kothari AK, Jian K, Rankin J, Sheldon BW (2008) Comparison between carbon nanotube and carbon nanofiber reinforcements in amorphous silicon nitride coatings. J Am Ceram Soc 91:2743–2746
Kothari AK, Hu S, Xia Z, Konca E, Sheldon BW (2012) Enhanced fracture toughness in carbon-nanotube-reinforced amorphous silicon nitride nanocomposite coatings. Acta Mater 60:3333–3339
Vasudevan S, Kothari A, Sheldon BW (2016) Direct observation of toughening and R-curve behavior in carbon nanotube reinforced silicon nitride. Scr Mater 124:112–116
Poyato R, Vasiliev AL, Padture NP, Tanaka H, Nishimura T (2006) Aqueous colloidal processing of single-wall carbon nanotubes and their composites with ceramics. Nanotechnology 17:1770–1777
Zhang SC, Fahrenholtz WG, Hilmas GE, Yadlowsky EJ (2010) Pressureless sintering of carbon nanotube-Al2O3composites. J Eur Ceram Soc 30:1373–1380
Fan J, Zhao D, Wu M, Xu Z, Song J (2006) Preparation and microstructure of multi-wall carbon nanotubes-toughened Al2O3 composite. J Am Ceram Soc 89:750–753
Liu Y, Ramirez C, Zhang L, Wu W, Padture NP (2017) In situ direct observation of toughening in isotropic nanocomposites of alumina ceramic and multiwall carbon nanotubes. Acta Mater 127:203–210
Sun J, Iwasa M, Gao L, Zhang Q (2004) Single-walled carbon nanotubes coated with titania nanoparticles. Carbon 42:895–899
Balázsi C, Fényi B, Hegman N, Kövér Z, Wéber F, Vértesy Z, Kónya Z, Kiricsi I, Biró LP, Arató P (2006) Development of CNT/Si3N4 composites with improved mechanical and electrical properties. Compos Part B Eng 37:418–424
Estili M, Kawasaki A, Sakka Y (2012) Highly concentrated 3D macrostructure of individual carbon nanotubes in a ceramic environment. Adv Mater 24:4322–4326
Estili M, Sakka Y (2014) Recent advances in understanding the reinforcing ability and mechanism of carbon nanotubes in ceramic matrix composites. Sci Technol Adv Mater 15:64902
Zapata-Solvas E, Gómez-García D, Domínguez-Rodríguez A (2012) Towards physical properties tailoring of carbon nanotubes-reinforced ceramic matrix composites. J Eur Ceram Soc 32:3001–3020
Berguiga L, Bellessa J, Vocanson F, Bernstein E, Plenet JC (2006) Carbon nanotube silica glass composites in thin films by the sol-gel technique. Opt Mater 28:167–171
Zhang Y, Shen Y, Han D, Wang Z, Song J, Niu L (2006) Reinforcement of silica with single-walled carbon nanotubes through covalent functionalization. J Mater Chem 16:4592–4597
Thomas BJC, Shaffer MSP, Boccaccini AR (2009) Sol-gel route to carbon nanotube borosilicate glass composites. Compos Part A Appl Sci Manuf 40:837–845
López AJ, Rico A, Rodríguez J, Rams J (2010) Tough ceramic coatings: carbon nanotube reinforced silica sol-gel. Appl Surf Sci 256:6375–6384
López AJ, Ureña A, Rams J (2011) Wear resistant coatings: silica sol-gel reinforced with carbon nanotubes. Thin Solid Films 519:7904–7910
Mo CB, Cha SI, Kim KT, Lee KH, Hong SH (2005) Fabrication of carbon nanotube reinforced alumina matrix nanocomposite by sol-gel process. Mater Sci Eng A 395:124–128
Cha SI, Kim KT, Lee KH, Mo CB, Hong SH (2005) Strengthening and toughening of carbon nanotube reinforced alumina nanocomposite fabricated by molecular level mixing process. Scr Mater 53:793–797
Yamamoto G, Omori M, Hashida T, Kimura H (2008) A novel structure for carbon nanotube reinforced alumina composites with improved mechanical properties. Nanotechnology 19:315708
Echeberria J, Rodríguez N, Vleugels J, Vanmeensel K, Reyes-Rojas A, Garcia-Reyes A, Dominguez-Rios C, Aguilar-Elguezabal A, Bocanegra-Bernal MH (2012) Hard and tough carbon nanotube-reinforced zirconia-toughened alumina composites prepared by spark plasma sintering. Carbon 50:706–717
Kasperski A, Weibel A, Alkattan D, Estournès C, Turq V, Laurent C, Peigney A (2013) Microhardness and friction coefficient of multi-walled carbon nanotube-yttria-stabilized ZrO2 composites prepared by spark plasma sintering. Scr Mater 69:338–341
Ma RZ, Wu J, Wei BQ, Liang J, Wu DH (1998) Processing and properties of carbon nanotubes-nano-SiC ceramic. J Mater Sci 33:5243–5246
Morisada Y, Miyamoto Y, Takaura Y, Hirota K, Tamari N (2007) Mechanical properties of SiC composites incorporating SiC-coated multi-walled carbon nanotubes. Int J Refract Met Hard Mater 25:322–327
Sarkar K, Sarkar S, Das PK (2016) Spark plasma sintered multiwalled carbon nanotube/silicon carbide composites: densification, microstructure, and tribo-mechanical characterization. J Mater Sci 51:6697–6710
Gu Z, Yang Y, Li K, Tao X, Eres G, Howe JY, Zhang L, Li X, Pan Z (2011) Aligned carbon nanotube-reinforced silicon carbide composites produced by chemical vapor infiltration. Carbon 49:2475–2482
Balázsi C, Shen Z, Kónya Z, Kasztovszky Z, Wéber F, Vertesy Z, Biro LP, Kiricsi I, Arato P (2005) Processing of carbon nanotube reinforced silicon nitride composites by spark plasma sintering. Compos Sci Technol 65:727–733
Corral EL, Cesarano J, Shyam A, Lara-Curzio E, Bell N, Stuecker J, Perry N, Di Prima M, Munir Z, Garay J, Barrera EV (2008) Engineered nanostructures for multifunctional single-walled carbon nanotube reinforced silicon nitride nanocomposites. J Am Ceram Soc 91: 3129–3137
Li A, Sun K, Dong W, Zhao D (2007) Mechanical properties, microstructure and histocompatibility of MWCNTs/HAp biocomposites. Mater Lett 61:1839–1844
Meng YH, Tang CY, Tsui CP, Chen DZ (2008) Fabrication and characterization of needle-like nano-HA and HA/MWNT composites. J Mater Sci Mater Med 19:75–81
Lahiri D, Singh V, Keshri AK, Seal S, Agarwal A (2010) Carbon nanotube toughened hydroxyapatite by spark plasma sintering: microstructural evolution and multiscale tribological properties. Carbon 48:3103–3120
Lei T, Wang L, Ouyang C, Li NF, Zhou LS (2011) In situ preparation and enhanced mechanical properties of carbon nanotube/hydroxyapatite composites. Int J Appl Ceram Technol 8:532–539
Guo S, Sivakumar R, Kagawa Y (2007) Multiwall carbon nanotube-SiO2 nanocomposites: sintering, elastic properties, and fracture toughness. Adv Eng Mater 9:84–87
Sun J, Gao L, Li W (2002) Colloidal processing of carbon nanotube/alumina composites. Chem Mater 14:5169–5172
Anstis GR, Chantikul P, Lawn BR, Marshall DB (1981) A critical evaluation of indentation techniques for measuring fracture toughness: I, direct crack measurements. J Am Ceram Soc 64:533–538
Quinn GD, Bradt RC (2007) On the vickers indentation fracture toughness test. J Am Ceram Soc 90:673–680
Jiang D, Thomson K, Kuntz JD, Ager JW, Mukherjee AK (2007) Effect of sintering temperature on a single-wall carbon nanotube-toughened alumina-based nanocomposite. Scr Mater 56:959–962
Padture NP, Curtin WA (2008) Comment on “Effect of sintering temperature on a single-wall carbon nanotube-toughened alumina-based composite”. Scr Mater 58:989–990
Jiang D, Mukherjee AK (2008) Response to comment on “Effect of sintering temperature on single-wall carbon nanotube toughened alumina-based nanocomposite”. Scr Mater 58: 991–993
Bakshi SR, Musaramthota V, Virzi DA, Keshri AK, Lahiri D, Singh V, Seal S, Agarwal A (2011) Spark plasma sintered tantalum carbide-carbon nanotube composite: effect of pressure, carbon nanotube length and dispersion technique on microstructure and mechanical properties. Mater Sci Eng A 528:2538–2547
Nisar A, Ariharan S, Balani K (2016) Synergistic reinforcement of carbon nanotubes and silicon carbide for toughening tantalum carbide based ultrahigh temperature ceramic. J Mater Res 31:682–692
Zapata-Solvas E, Poyato R, Gómez-García D, Domínguez-Rodríguez A, Radmilovic V, Padture NP (2008) Creep-resistant composites of alumina and single-wall carbon nanotubes. Appl Phys Lett 92:111912
Zapata-Solvas E, Gómez-García D, Poyato R, Lee Z, Castillo-Rodríguez M, Domínguez-Rodríguez A, Radmilovic V, Padture NP (2010) Microstructural effects on the creep deformation of alumina/single-wall carbon nanotubes composites. J Am Ceram Soc 93:2042–2047
Daraktchiev M, Van de Moortèle B, Schaller R, Couteau E, Forró L (2005) Effects of carbon nanotubes on grain boundary sliding in zirconia polycrystals. Adv Mater 17:88–91
Ionascu C, Schaller R (2006) Influence of carbon nanotubes and silicon carbide whiskers on the mechanical loss due to grain boundary sliding in 3-mol% yttria-stabilized tetragonal zirconia polycrystals. Mater Sci Eng A 442:175–178
Mazaheri M, Mari D, Hesabi ZR, Schaller R, Fantozzi G (2011) Multi-walled carbon nanotube/nanostructured zirconia composites: outstanding mechanical properties in a wide range of temperature. Compos Sci Technol 71:939–945
An JW, You DH, Lim DS (2003) Tribological properties of hot-pressed alumina-CNT composites. Wear 255:677–681
Ahmad I, Kennedy A, Zhu YQ (2010) Wear resistant properties of multi-walled carbon nanotubes reinforced Al2O3 nanocomposites. Wear 269:71–78
Lim DS, You DH, Choi HJ, Lim SH, Jang H (2005) Effect of CNT distribution on tribological behavior of alumina-CNT composites. Wear 259:539–544
Zhai W, Srikanth N, Kong LB, Zhou K (2017) Carbon nanomaterials in tribology. Carbon 119:150–171
Ni B, Sinnott SB (2001) Tribological properties of carbon nanotube bundles predicted from atomistic simulations. Surf Sci 487:87–96
Balani K, Chen Y, Harimkar SP, Dahotre NB, Agarwal A (2007) Tribological behavior of plasma-sprayed carbon nanotube-reinforced hydroxyapatite coating in physiological solution. Acta Biomater 3:944–951
Wells JK, Beaumont PWR (1985) Debonding and pull-out processes in fibrous composites. J Mater Sci 20:1275–1284
Suzuki T, Sato M, Sakai M (2011) Fiber pullout processes and mechanisms of a carbon fiber reinforced silicon nitride ceramic composite. J Mater Res 7:2869–2875
Estili M, Kawasaki A (2010) Engineering strong intergraphene shear resistance in multi-walled carbon nanotubes and dramatic tensile improvements. Adv Mater 22:607–610
Estili M, Kawasaki A, Pittini-Yamada Y, Utke I, Michler J (2011) In situ characterization of tensile-bending load bearing ability of multi-walled carbon nanotubes in alumina-based nanocomposites. J Mater Chem 21:4272–4278
Yamamoto G, Shirasu K, Hashida T, Takagi T, Suk JW, An J, Piner RD, Ruoff RS (2011) Nanotube fracture during the failure of carbon nanotube/alumina composites. Carbon 49: 3709–3716
Padture NP (2009) Multifunctional composites of ceramics and single-walled carbon nanotubes. Adv Mater 21:1767–1770
Ahmad I, Unwin M, Cao H, Chen H, Zhao H, Kennedy A, Zhu YQ (2010) Multi-walled carbon nanotubes reinforced Al2O3 nanocomposites: mechanical properties and interfacial investigations. Compos Sci Technol 70:1199–1206
Fan JP, Zhuang DM, Zhao DQ, Zhang G, Wu MS, Wei F, Fan ZJ (2006) Toughening and reinforcing alumina matrix composite with single-wall carbon nanotubes. Appl Phys Lett 89:1–4
Li L, Li Y (2017) Development and trend of ceramic cutting tools from the perspective of mechanical processing. IOP Conf Ser Earth Environ Sci 94:012062
Li K, Yang Y, Gu Z, Howe JY, Eres G, Zhang L, Li X, Pan Z (2014) Approaching carbon nanotube reinforcing limit in B4C matrix composites produced by chemical vapor infiltration. Adv Eng Mater 16:161–166
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Section Editor information
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this entry
Cite this entry
Gurnani, L., Mukhopadhyay, A. (2019). Development of Carbon Nanotube-Reinforced Ceramic Matrix Nanocomposites for Advanced Structural Applications. In: Mahajan, Y., Roy, J. (eds) Handbook of Advanced Ceramics and Composites. Springer, Cham. https://doi.org/10.1007/978-3-319-73255-8_30-1
Download citation
DOI: https://doi.org/10.1007/978-3-319-73255-8_30-1
Received:
Accepted:
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-73255-8
Online ISBN: 978-3-319-73255-8
eBook Packages: Springer Reference Chemistry and Mat. ScienceReference Module Physical and Materials ScienceReference Module Chemistry, Materials and Physics