Definition of the Subject and Its Importance
Geothermal systems are dynamic entities in which the liquid and vapor phases of water are the main mobile constituents. In their natural state these are generally in a quasi steady-state condition, when considered over a long period of time (>1,000 years). However, when fluid is withdrawn for the purpose of extracting energy then changes may occur within the system. These changes can result in a variety of environmental effects some of which are undesirable and so to manage the extraction of energy in a sustainable and environmentally responsible way it is necessary to monitor the changes. By monitoring the changes with time it is possible to understand and model the effects these changes may have on the environment and take steps to minimize any undesirable effects in a timely manner. Changes may also have engineering implications for a geothermal development, especially for a power station. One example is a decrease in the pressure of...
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Abbreviations
- Anchor grouting:
-
Concrete pumped into the rocks around the upper part of the well to anchor the well and well cellar to the near-surface rock formations.
- Aquiclude:
-
A geological formation (or formations) which will not transmit water; a barrier to vertical movement of geothermal fluid.
- Aquifer:
-
A geological formation (or formations) which contains water or geothermal fluid and will allow fluid movement.
- Baseline:
-
Data set acquired before exploitation begins, against which any future measurements are compared.
- Benchmark:
-
Permanent survey mark, often consisting of a stainless steel pin set in a concrete block or in the concrete base of a pipeline support.
- Bleed:
-
A well that is throttled back to a minimum flow is said to be “on bleed.” It is often risky to completely shut down a geothermal production well because it may be difficult to restart. Bleeding also keeps the wellbore heated which minimizes corrosion.
- Deep liquid level:
-
Boundary between the two-phase and deep liquid zones.
- Deep liquid zone:
-
Region of single phase liquid conditions below a two-phase (liquid and vapor) zone.
- Developer:
-
Company or organization which locates or uses geothermal energy for domestic or industrial purposes.
- Dryout:
-
The process whereby liquid saturation in the pores decreases and the vapor saturation increases, as a result of a decrease in pressure.
- Epicenter:
-
The point on the Earth’s surface directly above the hypocenter or focus of an earthquake.
- Geothermal system:
-
A body of hot water and rock within the Earth.
- Go-devil:
-
A tool for determining wellbore clearances or for scraping out obstructions from a well or pipeline.
- Groundwater:
-
Water, generally cold and of meteoric origin, which resides in near-surface aquifers and is often used for domestic and industrial purposes.
- High-temperature system:
-
A geothermal system, or part thereof, containing fluid having a temperature greater than 150°C; c.f. low-temperature system in which the temperature is less than 150°C. Note, however, that this temperature value is arbitrary and that different authorities adopt different values, or divide the range into low, intermediate, and high temperature.
- Hypocenter:
-
The focus or focal point of an earthquake (x, y, z) c.f. epicenter (x, y).
- Injection (syn. reinjection):
-
The process of returning waste water from a geothermal power station or industrial process back into the ground. This generally occurs around the edges of the field and may not be into the production aquifer from which fluid is drawn off to the power station.
- Injection aquifer:
-
The formation into which injected fluid is put. Generally this has high porosity and permeability.
- Liquid-dominated system:
-
A geothermal system, or part thereof, in which the pressure is hydrostatically controlled; c.f. steam (vapor)-dominated system, where the pressure is steam-static.
- Make-up well:
-
Well drilled to replace production lost from an existing production well, due to decreases in fluid temperature or pressure.
- Perched aquifer:
-
An aquifer of limited lateral extent which is separated from an underlying body of groundwater by unsaturated rock.
- Permeability:
-
A measure of the capacity of a geological rock formation to transmit a fluid.
- Production zone:
-
That region (depth) of the geothermal reservoir from which most of the production of fluid occurs.
- Reservoir:
-
The region of a geothermal system from which geothermal fluid is withdrawn, or is capable of being withdrawn.
- Residual (liquid) saturation:
-
The amount of liquid that remains in the pores (as % of pore volume) which decreases in pressure will not vaporize. The liquid saturation level below which vaporization of liquid will not occur.
- Steam zone:
-
A region of the reservoir in which steam (vapor) is the pressure-controlling phase.
- Trigger point:
-
A measured value at which it is considered action needs to be taken to prevent or avoid some detrimental occurrence happening, or exceeding some predetermined limit.
- Two (2)-phase zone:
-
A region where the liquid and vapor (steam) phases of water coexist in pores or fractures.
- Vadose zone:
-
The region of unsaturated rock and soil between the ground surface and the shallow groundwater level.
- Waste water:
-
Geothermal water from which energy has been extracted and is no longer required. This may be separated water, or steam which has passed through turbines or a binary plant and been condensed.
Bibliography
Primary Literature
Thain IA, Carey BS (2009) Fifty years of geothermal power generation at Wairakei. Geothermics 38(1):48–63
Allis RG, Hunt TM (1986) Analysis of exploitation induced gravity changes at Wairakei geothermal field. Geophysics 51:1647–1660
Bixley PF, Clotworthy AW, Mannington WI (2009) Evolution of the Wairakei geothermal reservoir during 50 years of production. Geothermics 38(1):145–154
Yoder JL (1998) Using meters to measure steam flow. http://www.flowresearch.com/articles/Plant_Engineering_0498.pdf
Mattar WM (2005) Advances in Coriolis technology resolve tough pipeline flow measurement challenges. Pipeline Gas J, July 2005. http://www.pipelineandgasjournal.com
Bixley PF, Wilson DM (1985) Rapid casing corrosion in high temperature liquid dominated geothermal fields. In: Proceedings of the 10th Workshop on Geothermal Reservoir Engineering, Stanford, pp 35–40
Bowyer D, Bignall G, Hunt T (2008) Formation and neutralization of corrosive fluids in the shallow injection aquifer, Rotokawa geothermal field, New Zealand. GRC Trans 32:201–205
Bixley PF, Hattersley SD (1983) Long term casing performance of Wairakei production wells. In: Proceedings of the 5th NZ Geothermal Workshop, Auckland, pp 257–263
Glover RB, Mroczek EK (2009) Chemical changes in natural features and well discharges in response to production at Wairakei, New Zealand. Geothermics 38(1):117–133
Klyen LE (1973) A vessel for collecting subsurface water samples from geothermal drillholes. Geothermics 2:57–60
Arnórsson S, Bjarnason JÖ, Giroud N, Gunnarsson I, Stefánsson A (2006) Sampling and analysis of geothermal fluids. Geofluids 6(3):203–216
Grob RL, Barry EF (2004) Modern practice of gas chromatography, 4th edn. Wiley-Interscience, New York, 1064 pp. ISBN-10: 0471229830, ISBN-13: 978-0471229834
Rose PE, Apperson KD, Johnson SD, Adams MC (1997) Numerical simulation of a tracer test at Dixie Valley, Nevada. In: Proceedings of the 22nd Workshop on Geothermal Reservoir Engineering, Stanford, pp 169–176
Adams MC, Beall JJ, Enedy SL, Hirtz PN, Kilbourn P, Koenig BA, Kunzman R, Smith JL (2001) Hydrofluorocarbons as geothermal vapor-phase tracers. Geothermics 30(6):747–775
Hirtz PN, Kunzman RJ, Broaddus MK, Barbitta JA (2001) Developments in tracer flow testing for geothermal production engineering. Geothermics 30(6):727–745
McCabe WJ, Barry BJ, Manning MR (1983) Radioactive tracers in geothermal underground water flow studies. Geothermics 12:83–110
Massonnet D, Holzer T, Vadon H (1997) Land subsidence caused by the East Mesa geothermal field, California, observed using SAR interferometry. Geophys Res Lett 24:901–904
Massonnet D, Feigl KL (1998) Radar interferometry and its application to changes in the earth’s surface. Rev Geophys 36:441–500
Hsing-Chung C, Linlin G, Rizos C (2005) InSAR and mathematical modelling for measuring surface deformation due to geothermal water extraction in New Zealand. In: Proceedings of the 2005 IEEE International Geoscience and Remote Sensing Symposium, vol 3, pp 1587–1589
Hole JK, Bromley CJ, Stevens NF, Wadge G (2007) Subsidence in the geothermal fields of the Taupo Volcanic Zone, New Zealand from 1996 to 2005 measured by InSAR. J Volcanol Geoth Res 166:125–146
Allis RG, Bromley CJ, Currie S (2009) Update on subsidence at the Wairakei-Tauhara geothermal system. Geothermics 38(1):169–180
Bromley CJ (2009) Groundwater changes in the Wairakei-Tauhara geothermal system. Geothermics 38(1):134–144
Bromley CJ, Hunt TM, Morris C (1993) Cold downflows of groundwater at Ohaaki Geothermal Field; preliminary results. In: Proceedings of the 15th New Zealand Geothermal Workshop, Auckland, pp 181–186
Hunt TM, Bromley CJ, Risk GF, Sherburn S, Soengkono S (2009) Geophysical investigations of the Wairakei Field. Geothermics 38(1):85–97
Hunt TM (1970) Gravity changes at Wairakei Geothermal Field, New Zealand. Geol Soc Am Bull 81:529–536
Atkinson PG, Pedersen JR (1988) Using precision gravity data in geothermal reservoir engineering modelling studies. In: Proceedings of the 13th Workshop on Geothermal Reservoir Engineering, Stanford, pp 35–40
Hunt TM, Allis RG, Blakely MR, O’Sullivan MJ (1990) Testing reservoir simulation models for the Broadlands Geothermal Field using precision gravity data. Geoth Resour Counc Trans 14:1287–1294
Hunt TM (2005) Using repeat microgravity measurements to track reinjection in a liquid-dominated field. In: Proceedings of the World Geothermal Congress 2005 (CD). Paper No. 1117
Hunt TM, Kissling WM (1994) Determination of reservoir properties at Wairakei Geothermal Field using gravity change measurements. J Volcanol Geoth Res 63:129–143
Majer EL, Baria R, Stark M, Oates S, Bommer J, Smith B, Asanuma H (2007) Induced seismicity associated with Enhanced Geothermal Systems. Geothermics 36:185–222
Sherburn S, Allis RG, Clotworthy A (1990) Microseismic activity at Wairakei and Ohaaki geothermal fields. In: Proceedings of the 12th NZ Geothermal Workshop, Auckland, pp 51–55
Stein S, Wysession M (2002) An Introduction to seismology, earthquakes, and earth structure. Wiley-Blackwell, Oxford, 512 pp. ISBN: 978-0-86542-078-6
Zuccaa JJ, Hutchingsa LJ, Kasameyera PW (1994) Seismic velocity and attenuation structure of the Geysers geothermal field, California. Geothermics 23(2):111–126
Bommer JJ, Oates S, Cepeda JM, Lindholm C, Bird J, Torres R, Marroquín G, Rivas J (2006) Control of hazard due to seismicity induced by a hot fractured rock geothermal project. Eng Geol 83:287–306
Smith B, Beall J, Stark M (2000) Induced seismicity in the SE Geysers field, California, USA. In: Proceedings of the World Geothermal Congress 2000, Kyushu-Tohuku, Japan, pp 2887–2892
White PA, Hunt TM (1996) Simple modelling of the effects of exploitation on hot springs, Geyser Valley, Wairakei, New Zealand. Geothermics 34:184–204
Cataldi R, Hodgson SF, Lund JW (1999) Stories from a heated Earth. Geothermal Resources Council and the International Geothermal Association, Sacramento, California, 569 pp. ISBN 0-934412-19-7
Books and Reviews
Armstead HCH (1980) Geothermal energy: its past, present and future contributions to the energy needs of man. E & F.N. Spon, London
Dickson MH, Fanelli M (2003) Geothermal energy utilization and technology. UNESCO Publishing, Paris, 205 pp. ISBN 92-3-103915-6
DiPippo R (2008) Geothermal power plants: principles, applications, case studies and environmental impact, 2nd edn. Butterworth-Heinemann, Oxford, 520 pp. ISBN: 978-0-7506-8620-4
Ellis AJ, Mahon WAJ (1977) Chemistry and geothermal systems. Academic, New York, 392 pp. ISBN: 0-12-237450-9
Grant MA, Donaldson IG, Bixley PF (1982) Geothermal reservoir engineering. Academic, New York, 369 pp. ISBN: 0-12-295620-6
Hunt TM (2001) Five lectures on environmental effects of geothermal utilization. Report 2000-1, United Nations University, Reykjavik, Iceland, 109 pp. ISBN-9979-68-070-9
http://os.is/Apps/WebObjects/Orkustofnun.woa/swdocument/2056/Trevor03.pdf
Kruger P, Otte C (1973) Geothermal energy: resources, production, stimulation. Stanford University Press, California, 360 pp
Rybach L, Muffler LJP (1981) Geothermal systems: principles and case histories. Wiley, New York
Thorhallsson S (2003) Geothermal well operation and maintenance. IGC2003 – Short Course September 2003:195–217. http://unugtp.is/Apps/WebObjects/Orkustofnun.woa/swdocument/539/13Sverrir.pdf
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2012 Springer Science+Business Media, LLC
About this entry
Cite this entry
Hunt, T.M. (2012). Geothermal Field and Reservoir Monitoring . In: Meyers, R.A. (eds) Encyclopedia of Sustainability Science and Technology. Springer, New York, NY. https://doi.org/10.1007/978-1-4419-0851-3_298
Download citation
DOI: https://doi.org/10.1007/978-1-4419-0851-3_298
Publisher Name: Springer, New York, NY
Print ISBN: 978-0-387-89469-0
Online ISBN: 978-1-4419-0851-3
eBook Packages: Earth and Environmental ScienceReference Module Physical and Materials ScienceReference Module Earth and Environmental Sciences