Advertisement

Nano-functionalized Polycarbonate Coatings for Heat Sink Applications

  • Prasansha Rastogi
  • Neha Katiyar
  • Swaroop Gharde
  • Balasubramanian KandasubramanianEmail author
Living reference work entry

Abstract

Thermoplastic/thermosetting polymer composites are a category of advanced functional materials having competency to replace many conventional materials due to its lightweight and excellent heat sinking capacity for automotive, aviation, and defense. The heat transfer and dissipation mechanism are basics considered for developing new material with improved heat insulation capacity. Polycarbonate composite comprising nanofiller/-fiber reinforcements fabricated with advanced technique inherits properties such as good mechanical properties, thermal stability, optical clarity, etc. required for thermal insulation. In this chapter, polycarbonate nanocomposites were fabricated though three different methods, i.e., solvent casting, spray coating, and melt mixing with three different reinforced fillers cenosphere, fumed silica (FS), and POSS. Functionalization, effectiveness in surface treatment, changes in surface morphology, and insulation characteristics of composite were affirmed through varied surface, morphology, and thermal characterization tools. Thermal conductivity of composites was also computed theoretically, and steady heat transfer simulation had been carried out to analyze the results numerically using ABAQUS CAE tool. To extend the application field of polycarbonate composites, water contact angle had been measured to check hydrophobic or hydrophilic nature of composites. Finally, the chapter concludes with detailed comparative study of polycarbonate nanocomposites with fillers fabricated by three different techniques with an application in car battery casing. Results displayed enhanced properties of polycarbonate nanocomposites which have a competency to replace the conventional materials used for insulative purpose.

Keywords

High-temperature polymers Heat sink Polycarbonate Nano-fumed silica Polymeric coatings Nanomaterials 

References

  1. Abbasi S, Carreau PJ, Derdouri A (2010) Flow induced orientation of multiwalled carbon nanotubes in polycarbonate nanocomposites: rheology, conductivity and mechanical properties. Polymer 51:922–935CrossRefGoogle Scholar
  2. Agrawal A, Satapathy A (2015) Computational, analytical and experimental investigation of heat conduction of particulate filled polymer composite. Universal J Mech Eng 3:1–6CrossRefGoogle Scholar
  3. Akonda MH, Lawrence CA, Weager BM (2012) Recycled carbon fibre-reinforced polypropylene thermoplastic composites. Compos A: Appl Sci Manuf 43:79–86CrossRefGoogle Scholar
  4. Armster SQ, Delplanque J-P, Rein M, Lavernia EJ (2002) Thermo–fluid mechanisms controlling droplet based materials processes. Int Mater Rev 47:265–301CrossRefGoogle Scholar
  5. Ashish J, Swaroop G, Balasubramanian K (2019) Effect of ammonium perchlorate particle size on flow, ballistic, and mechanical properties of composite propellant. In: Yan Q-L, He G-Q, Liu P-J, Gozin M (eds) Nanomaterials in rocket propulsion systems. Elsevier, Amsterdam, pp 299–362CrossRefGoogle Scholar
  6. Badhe Y, Balasubramanian K (2014) Reticulated three-dimensional network ablative composites for heat shields in thermal protection systems. RSC Adv 4:43708–43719CrossRefGoogle Scholar
  7. Badhe Y, Balasubramanian K, Gupta R (2015) Cost-effective, low density, carbon soot doped resorcinol formaldehyde composite for ablative applications. RSC Adv 5:23622–23634CrossRefGoogle Scholar
  8. Baglari S, Kole M, Dey TK (2011) Effective thermal conductivity and coefficient of linear thermal expansion of high-density polyethylene—fly ash composites. Indian J Phys 85:559–573CrossRefGoogle Scholar
  9. Balasubramanian K (2012) Reinforcement of poly ether sulphones (PES) with exfoliated graphene oxide for aerospace applications. IOP Conf Ser Mater Sci Eng 40:012022CrossRefGoogle Scholar
  10. Balasubramanian K, Tirumalai M (2013) High temperature polymer nanocomposites. In: Njuguna J (ed) Structural nanocomposites. Springer, Berlin/Heidelberg, pp 165–186CrossRefGoogle Scholar
  11. Balasubramanian K, Tirumali M, Badhe Y, Mahajan YR (2017) Nano-enabled multifunctional materials for aerospace applications. In: Prasad NE, Wanhill RJH (eds) Aerospace materials and material technologies. Springer, Singapore, pp 439–453CrossRefGoogle Scholar
  12. Banerjee BS, Balasubramanian K (2015) Nanotexturing of PC/n-HA nanocomposites by innovative and advanced spray system. RSC Adv 5:13653–13659CrossRefGoogle Scholar
  13. Banerjee BS, Khaira SS, Balasubramanian K (2014) Thin film encapsulation of nano composites of polycarbonate (PC) for thermal management systems. RSC Adv 4:63380–63386CrossRefGoogle Scholar
  14. Bartuli C, Lusvarghi L, Manfredini T, Valente T (2007) Thermal spraying to coat traditional ceramic substrates: case studies. J Eur Ceram Soc 27:1615–1622CrossRefGoogle Scholar
  15. Batt RG, Legner HH (1983) A review of roughness-induced Nosetip transition. AIAA J 21:7–22CrossRefGoogle Scholar
  16. Cai HL, Xu K, Liu H, Liu X, Fu ZE, Chen MC (2011) Influence of polyhedral oligomeric silsesquioxanes on thermal and mechanical properties of polycarbonate/POSS hybrid composites. Polym Compos 32:1343–1351CrossRefGoogle Scholar
  17. Cao XQ, Vassen R, Stoever D (2004) Ceramic materials for thermal barrier coatings. J Eur Ceram Soc 24:1–10CrossRefGoogle Scholar
  18. Chen Y, Zhan J, Zhang P, Nie S, Lu H, Song L, Hu Y (2010) Preparation of intumescent flame retardant Poly(butylene succinate) using Fumed silica as synergistic agent. Ind Eng Chem Res 49:8200–8208CrossRefGoogle Scholar
  19. Chrissafis K, Paraskevopoulos KM, Pavlidou E, Bikiaris D (2009a) Thermal degradation mechanism of HDPE nanocomposites containing fumed silica nanoparticles. Thermochim Acta 485:65–71CrossRefGoogle Scholar
  20. Chrissafis K, Paraskevopoulos KM, Tsiaoussis I, Bikiaris D (2009b) Comparative study of the effect of different nanoparticles on the mechanical properties, permeability, and thermal degradation mechanism of HDPE. J Appl Polym Sci 114:1606–1618CrossRefGoogle Scholar
  21. Daniel A, Badhe Y, Srikanth I, Gokhale S, Balasubramanian K (2016) Laser shielding and thermal ablation characteristics of resorcinol formaldehyde/boron nitride composites for thermal protection systems. Ind Eng Chem Res 55:10645–10655CrossRefGoogle Scholar
  22. Daniel A, Ivaturi S, Kumar A, Kandasubramanian B (2019) Development and characterization of a contoured passive thermal protection system. Int J Appl Ceram Technol 16:170–184CrossRefGoogle Scholar
  23. Das TK, Prusty S (2013) Graphene-based polymer composites and their applications. Polym-Plast Technol Eng 52:319–331CrossRefGoogle Scholar
  24. Das A, Satapathy BK (2011) Structural, thermal, mechanical and dynamic mechanical properties of cenosphere filled polypropylene composites. Mater Des 32:1477–1484CrossRefGoogle Scholar
  25. Dawson DM, Briggs A (1981) Prediction of the thermal conductivity of insulation materials. J Mater Sci 16:3346–3356CrossRefGoogle Scholar
  26. Deepthi MV, Sharma M, Sailaja RRN, Anantha P, Sampathkumaran P, Seetharamu S (2010) Mechanical and thermal characteristics of high density polyethylene–fly ash Cenospheres composites. Mater Des 31:2051–2060CrossRefGoogle Scholar
  27. Doyle CD (1961) Estimating thermal stability of experimental polymers by empirical thermogravimetric analysis. Anal Chem 33:77–79CrossRefGoogle Scholar
  28. Eklund PC, Holden JM, Jishi RA (1995) Vibrational modes of carbon nanotubes; spectroscopy and theory. Carbon 33:959–972CrossRefGoogle Scholar
  29. Ettlinger M, Ladwig T, Weise A (2000) Surface modified fumed silicas for modern coatings. Prog Org Coat 40:31–34CrossRefGoogle Scholar
  30. Favis BD, Therrien D (1991) Factors influencing structure formation and phase size in an immiscible polymer blend of polycarbonate and polypropylene prepared by twin-screw extrusion. Polymer 32:1474–1481CrossRefGoogle Scholar
  31. Feng J, Hao J, Du J, Yang R (2010) Flame retardancy and thermal properties of solid bisphenol A bis(diphenyl phosphate) combined with montmorillonite in polycarbonate. Polym Degrad Stab 95:2041–2048CrossRefGoogle Scholar
  32. Feng Y, Wang B, Wang F, Zhao Y, Liu C, Chen J, Shen C (2014) Thermal degradation mechanism and kinetics of polycarbonate/silica nanocomposites. Polym Degrad Stab 107:129–138CrossRefGoogle Scholar
  33. Fomenko EV, Anshits NN, Pankova MV, Solovyov LA, Anshits AG (2011) Fly ash cenospheres: Composition, morphology, structure, and helium permeability. In: World Coal Ash Conf.–May: 9–12, http://www.flyash.info/AshSymposium/AshLibraryAgenda.asp
  34. Fu BX, Hsiao BS, White H, Rafailovich M, Mather PT, Jeon HG, Phillips S, Lichtenhan J, Schwab J (2000) Nanoscale reinforcement of polyhedral oligomeric silsesquioxane (POSS) in polyurethane elastomer. Polym Int 49:437–440CrossRefGoogle Scholar
  35. Galvez A, Herlin-Boime N, Reynaud C, Clinard C, Rouzaud J-N (2002) Carbon nanoparticles from laser pyrolysis. Carbon 40:2775–2789CrossRefGoogle Scholar
  36. Gedler G, Antunes M, Realinho V, Velasco JI (2012) Thermal stability of polycarbonate-graphene nanocomposite foams. Polym Degrad Stab 97:1297–1304CrossRefGoogle Scholar
  37. Goffreda F, Griff A, Livinghouse L, Walsh T, Scuralli J (1998) Tool and Manufacturing Engineers Handbook Knowledge Base. Society of Manufacturing EngineersGoogle Scholar
  38. Gonte RR, Shelar G, Balasubramanian K (2014) Polymer–agro-waste composites for removal of Congo red dye from wastewater: adsorption isotherms and kinetics. Desalin Water Treat 52:7797–7811CrossRefGoogle Scholar
  39. Gore PM, Kandasubramanian B (2018a) Functionalized aramid fibers and composites for protective applications: a review. Ind Eng Chem Res 57:16537–16563CrossRefGoogle Scholar
  40. Gore PM, Kandasubramanian B (2018b) Heterogeneous wettable cotton based superhydrophobic Janus biofabric engineered with PLA/functionalized-organoclay microfibers for efficient oil–water separation. J Mater Chem A 6:7457–7479CrossRefGoogle Scholar
  41. Gore PM, Zachariah S, Gupta P, Kandasubramanian B (2016) Multifunctional nano-engineered and bio-mimicking smart superhydrophobic reticulated ABS/fumed silica composite thin films with heat-sinking applications. RSC Adv 6:105180–105191CrossRefGoogle Scholar
  42. Gore PM, Purushothaman A, Naebe M, Wang X, Kandasubramanian B (2019) Nanotechnology for oil-water separation. In: Prasad R, Karchiyappan T (eds) Advanced research in nanosciences for water technology. Springer International Publishing, Cham, pp 299–339CrossRefGoogle Scholar
  43. Gun’ko VM, Voronin EF, Pakhlov EM, Zarko VI, Turov VV, Guzenko NV, Leboda R, Chibowski E (2000) Features of fumed silica coverage with silanes having three or two groups reacting with the surface. Colloids Surf A Physicochem Eng Asp 166:187–201CrossRefGoogle Scholar
  44. Gupta P, Balasubramanian K (2016) Numerical investigation of heat loss in Nano-Fumed silica reinforced styrene acrylonitrile hydrophobic Thermo-sheath for heat inhibition in hydronic boiler. Mater Focus 5:556–564CrossRefGoogle Scholar
  45. Haddad TS, Lichtenhan JD (1996) Hybrid organic−inorganic thermoplastics: styryl-based polyhedral oligomeric Silsesquioxane polymers. Macromolecules 29:7302–7304CrossRefGoogle Scholar
  46. Hakimelahi HR, Hu L, Rupp BB, Coleman MR (2010) Synthesis and characterization of transparent alumina reinforced polycarbonate nanocomposite. Polymer 51:2494–2502CrossRefGoogle Scholar
  47. Han Z, Fina A (2011) Thermal conductivity of carbon nanotubes and their polymer nanocomposites: a review. Prog Polym Sci 36:914–944CrossRefGoogle Scholar
  48. Hany R, Hartmann R, Böhlen C, Brandenberger S, Kawada J, Löwe C, Zinn M, Witholt B, Marchessault RH (2005) Chemical synthesis and characterization of POSS-functionalized poly[3-hydroxyalkanoates]. Polymer 46:5025–5031CrossRefGoogle Scholar
  49. Hao N, Böhning M, Schönhals A (2007) Dielectric properties of nanocomposites based on polystyrene and polyhedral oligomeric Phenethyl-Silsesquioxanes. Macromolecules 40:9672–9679CrossRefGoogle Scholar
  50. Ho CJ, Chen WC (2013) An experimental study on thermal performance of Al2O3/water nanofluid in a minichannel heat sink. Appl Therm Eng 50:516–522CrossRefGoogle Scholar
  51. Hofmann D, Keinath M, Thomann R, Mülhaupt R (2014) Thermoplastic carbon/polyamide 12 composites containing functionalized graphene, expanded graphite, and carbon nanofillers: thermoplastic carbon/polyamide 12 composites containing functionalized graphene…. Macromol Mater Eng 299:1329–1342CrossRefGoogle Scholar
  52. Hornbostel B, Pötschke P, Kotz J, Roth S (2006) Single-walled carbon nanotubes/polycarbonate composites: basic electrical and mechanical properties. Phys Status Solidi (b) 243:3445–3451CrossRefGoogle Scholar
  53. Hussain CM (2018) Handbook of nanomaterials for industrial applications. Elsevier, AmsterdamGoogle Scholar
  54. Hussain CM, Mishra AK (2018) New polymer nanocomposites for environmental remediation. Elsevier, AmsterdamGoogle Scholar
  55. Irvine D, Foreman E, Remington CB, Jackson A, Endrizzi S (2015) Designing a heat sink for Lithium-ion battery packs in electric vehicles. US: University of AkronGoogle Scholar
  56. Ismail KN, Hussin K, Idris MS (2007) Physical, chemical & mineralogical properties of fly ash. Journal of Nuclear and Related Technology 4:47–51Google Scholar
  57. Jain S, Gupta G, Kshirsagar DR, Khire VH, Kandasubramanian B (2018) Burning rate and other characteristics of strontium titanate (SrTiO3) supplemented AP/HTPB/Al composite propellants. Def Technol.  https://doi.org/10.1016/j.dt.2018.10.004CrossRefGoogle Scholar
  58. Jindal P, Goyal M, Kumar N (2014) Mechanical characterization of multiwalled carbon nanotubes-polycarbonate composites. Mater Des. (1980-2015) 54:864–868CrossRefGoogle Scholar
  59. Kang H-J, Meesiri W, Blum FD (1990) Nuclear magnetic resonance studies of the hydrolysis and molecular motion of aminopropylsilane. Mater Sci Eng A 126:265–270CrossRefGoogle Scholar
  60. Karasek L, Sumita M, (1996) Characterization of dispersion state of filler and polymer-filler interactions in rubber-carbon black composites. J Mater Sci 31:281–289.  https://doi.org/10.1007/BF01139141
  61. Kashiwagi T, Du F, Douglas JF, Winey KI, Harris RH, Shields JR (2005) Nanoparticle networks reduce the flammability of polymer nanocomposites. Nat Mater 4:928–933CrossRefGoogle Scholar
  62. Katiyar N, Balasubramanian K (2014) Thermal modelling of hybrid composites of nano cenosphere and polycarbonate for a thermal protection system. RSC Adv 4:47529–47535CrossRefGoogle Scholar
  63. Katiyar N, Balasubramanian K (2015) Nano-heat-sink thin film composite of PC/three-dimensional networked nano-fumed silica with exquisite hydrophobicity. RSC Adv 5:4376–4384CrossRefGoogle Scholar
  64. Kolay PK, Singh DN (2001) Physical, chemical, mineralogical, and thermal properties of cenospheres from an ash lagoon. Cem Concr Res 31:539–542CrossRefGoogle Scholar
  65. Kumar V, Balasubramanian K (2016) Progress update on failure mechanisms of advanced thermal barrier coatings: a review. Prog Org Coat 90:54–82CrossRefGoogle Scholar
  66. Kumar V, Kandasubramanian B (2016) Processing and design methodologies for advanced and novel thermal barrier coatings for engineering applications. Particuology 27:1–28CrossRefGoogle Scholar
  67. Lee ES, Kim JS, Kim KY, Lim DY, Kim DH (2014) Preparation of polypropylene composites reinforced with long carbon fibers and their properties. Fibers Polym 15:2613–2617CrossRefGoogle Scholar
  68. Leng Y, Liu J, Zhang C, Jiang P (2014) A polyhedral oligomeric silsesquioxane (POSS)-bridged oxo-molybdenum Schiff base complex with enhanced heterogeneous catalytic activity in epoxidation. Cat Sci Technol 4:997–1004CrossRefGoogle Scholar
  69. Li G, Wang L, Ni H, Pittman CU Jr (2001) Polyhedral oligomeric Silsesquioxane (POSS) polymers and copolymers: a review. J Inorg Organomet Polym 11:123–154CrossRefGoogle Scholar
  70. Li GZ, Wang L, Toghiani H, Daulton TL, Pittman CU (2002) Viscoelastic and mechanical properties of vinyl ester (VE)/multifunctional polyhedral oligomeric silsesquioxane (POSS) nanocomposites and multifunctional POSS–styrene copolymers. Polymer 43:4167–4176CrossRefGoogle Scholar
  71. Li ZQ, Lu CJ, Xia ZP, Zhou Y, Luo Z (2007) X-ray diffraction patterns of graphite and turbostratic carbon. Carbon 45:1686–1695CrossRefGoogle Scholar
  72. Lin-Vien D, Colthup NB, Fateley WG, Grasselli JG (1991) The handbook of infrared and Raman characteristics frequency of organic molecules. AcademicGoogle Scholar
  73. Ma P-C, Siddiqui NA, Marom G, Kim J-K (2010) Dispersion and functionalization of carbon nanotubes for polymer-based nanocomposites: a review. Compos A: Appl Sci Manuf 41:1345–1367CrossRefGoogle Scholar
  74. Magisetty R, Kumar P, Gore PM, Ganivada M, Shukla A, Kandasubramanian B, Shunmugam R (2019) Electronic properties of Poly(1,6-heptadiynes) electrospun fibrous non-woven mat. Mater Chem Phys 223:343–352CrossRefGoogle Scholar
  75. Mishra P, Balasubramanian K (2014) Nanostructured microporous polymer composite imprinted with superhydrophobic camphor soot, for emphatic oil–water separation. RSC Adv 4:53291–53296CrossRefGoogle Scholar
  76. Moon SC, Kim JY, Oh BT (2014) Mechanical and flame resistant properties of polycarbonate-carbon nanotubes-ochre composites. Polym Eng Sci 54:1289–1299CrossRefGoogle Scholar
  77. Nakagaito AN, Yano H (2005) Novel high-strength biocomposites based on microfibrillated cellulose having nano-order-unit web-like network structure. Appl Phys A 80:155–159CrossRefGoogle Scholar
  78. Olmos D, Martínez F, González-Gaitano G, González-Benito J (2011) Effect of the presence of silica nanoparticles in the coefficient of thermal expansion of LDPE. Eur Polym J 47:1495–1502CrossRefGoogle Scholar
  79. Panwar SS, Patro TU, Balasubramanian K, Venkataraman B (2016) High-temperature stability of yttria-stabilized zirconia thermal barrier coating on niobium alloy—C-103. Bull Mater Sci 39:321–329CrossRefGoogle Scholar
  80. Parvaiz MR, Mahanwar PA, Mohanty S, Nayak SK (2010) Morphological, mechanical, thermal, electrical and rheological properties of polycarbonate composites reinforced with surfaces modified Mica. J Miner Mater Charact Eng 09:985–996Google Scholar
  81. Periyasamy T, Asrafali SP, Muthusamy S (2015) New benzoxazines containing polyhedral oligomeric silsesquioxane from eugenol, guaiacol and vanillin. New J Chem 39:1691–1702CrossRefGoogle Scholar
  82. Phillips SH, Haddad TS, Tomczak SJ (2004) Developments in nanoscience: polyhedral oligomeric silsesquioxane (POSS)-polymers. Curr Opinion Solid State Mater Sci 8:21–29CrossRefGoogle Scholar
  83. Poręba R, Spírková M, Hrdlicka Z (2011) Mechanical and thermomechanical properties of polycarbonate-based polyurethane-silica nanocomposites. Process Appl Ceram 5:155–159CrossRefGoogle Scholar
  84. Prasad A, Kandasubramanian B (2019) Fused deposition processing polycaprolactone of composites for biomedical applications. Polym-Plast Technol Mater 58(13):1365–98CrossRefGoogle Scholar
  85. Puri RG, Khanna AS (2016) Effect of cenospheres on the char formation and fire protective performance of water-based intumescent coatings on structural steel. Prog Org Coat 92:8–15CrossRefGoogle Scholar
  86. Raask E (1968) Cenospheres in pulverized-fuel ash. J Inst Fuel 41:339Google Scholar
  87. Raask E (1969) Fusion of silicate particles in coal flames. Fuel 48:366Google Scholar
  88. Ramdayal BK (2014) Antibacterial application of polyvinylalcohol-nanogold composite membranes. Colloids Surf A Physicochem Eng Asp 455:174–178CrossRefGoogle Scholar
  89. Reda DC (1981) Correlation of Nosetip boundary-layer transition data measured in ballistics-range experiments. AIAA J 19:329–339CrossRefGoogle Scholar
  90. Sánchez-Soto M, Schiraldi DA, Illescas S (2009) Study of the morphology and properties of melt-mixed polycarbonate–POSS nanocomposites. Eur Polym J 45:341–352CrossRefGoogle Scholar
  91. Sanoj P, Kandasubramanian B (2014) Hybrid carbon-carbon ablative composites for thermal protection in aerospace. J Compos 2014:1–15CrossRefGoogle Scholar
  92. Sengupta R, Bhattacharya M, Bandyopadhyay S, Bhowmick AK (2011) A review on the mechanical and electrical properties of graphite and modified graphite reinforced polymer composites. Prog Polym Sci 36:638–670CrossRefGoogle Scholar
  93. Sinha Ray S, Okamoto M (2003) Polymer/layered silicate nanocomposites: a review from preparation to processing. Prog Polym Sci 28:1539–1641CrossRefGoogle Scholar
  94. Song L, He Q, Hu Y, Chen H, Liu L (2008) Study on thermal degradation and combustion behaviors of PC/POSS hybrids. Polym Degrad Stab 93:627–639CrossRefGoogle Scholar
  95. Striolo A, McCabe C, Cummings PT (2005) Thermodynamic and transport properties of polyhedral oligomeric Silsesquioxanes in Poly(dimethylsiloxane). J Phys Chem B 109:14300–14307CrossRefGoogle Scholar
  96. Suryanegara L, Nakagaito AN, Yano H (2009) The effect of crystallization of PLA on the thermal and mechanical properties of microfibrillated cellulose-reinforced PLA composites. Compos Sci Technol 69:1187–1192CrossRefGoogle Scholar
  97. Suryanegara L, Okumura H, Nakagaito AN, Yano H (2011) The synergetic effect of phenylphosphonic acid zinc and microfibrillated cellulose on the injection molding cycle time of PLA composites. Cellulose 18:689–698CrossRefGoogle Scholar
  98. Sweileh BA, Al-Hiari YM, Kailani MH, Mohammad HA (2010) Synthesis and characterization of polycarbonates by melt phase interchange reactions of Alkylene and Arylene diacetates with Alkylene and Arylene Diphenyl Dicarbonates. Molecules 15:3661–3682CrossRefGoogle Scholar
  99. Tenjimbayashi M, Shiratori S (2014) Highly durable superhydrophobic coatings with gradient density by movable spray method. J Appl Phys 116:114310CrossRefGoogle Scholar
  100. Tirumali M, Balasubramanian K, Kumaraswamy A (2017) Functionally layered graphite reinforced epoxy composite sandwiched between epoxy composites: their electrical and flexural properties. Mater Focus 6:691–697CrossRefGoogle Scholar
  101. Tirumali M, Kandasubramanian B, Kumaraswamy A, Subramani NK, Suresha B (2018) Fabrication, physicochemical characterizations and electrical conductivity studies of modified carbon nanofiber-reinforced epoxy composites: effect of 1-Butyl-3-Methylimidazolium Tetrafluoroborate ionic liquid. Polym-Plast Technol Eng 57:218–228CrossRefGoogle Scholar
  102. Tong Z, Liu M, Bao H (2016) A numerical investigation on the heat conduction in high filler loading particulate composites. Int J Heat Mass Transf 100:355–361CrossRefGoogle Scholar
  103. Varadarajan S, Pattanaik AK, Sarin VK (2001) Mullite interfacial coatings for SiC fibers. Surf Coat Technol 139:153–160CrossRefGoogle Scholar
  104. Wang C, Wang D, Zheng S (2013) Preparation of aluminum silicate/fly ash particles composite and its application in filling polyamide 6. Mater Lett 111:208–210CrossRefGoogle Scholar
  105. Xu J, Song J (2010) High performance shape memory polymer networks based on rigid nanoparticle cores. Proc Natl Acad Sci 107:7652–7657CrossRefGoogle Scholar
  106. Yadav R, Zachariah S, Balasubramanian K (2016) Thermally stable transparent hydrophobic bio-mimetic dual scale Spherulites coating by spray deposition. Adv Sci Eng Med 8:181–187CrossRefGoogle Scholar
  107. Yadav R, Naebe M, Wang X, Kandasubramanian B (2017) Structural and thermal stability of polycarbonate decorated fumed silica nanocomposite via thermomechanical analysis and in-situ temperature assisted SAXS. Sci Rep.  https://doi.org/10.1038/s41598-017-08122-7
  108. Yadav R, Naebe M, Wang X, Kandasubramanian B (2019) Thermomechanical characteristics of h-BN- and POSS-based bisphenol A polycarbonate nanocomposites. Polymer-Plastics Technology and Materials 1–15  https://doi.org/10.1080/25740881.2018.1563143CrossRefGoogle Scholar
  109. Ye Y-S, Chen W-Y, Wang Y-Z (2006) Synthesis and properties of low-dielectric-constant polyimides with introduced reactive fluorine polyhedral oligomeric silsesquioxanes. J Polym Sci A Polym Chem 44:5391–5402CrossRefGoogle Scholar
  110. Yoon KH, Polk MB, Park JH, Min BG, Schiraldi DA (2005) Properties of poly(ethylene terephthalate) containing epoxy-functionalized polyhedral oligomeric silsesquioxane. Polym Int 54:47–53CrossRefGoogle Scholar
  111. Zheng L, Farris RJ, Coughlin EB (2001) Synthesis of polyethylene hybrid copolymers containing polyhedral oligomeric silsesquioxane prepared with ring-opening metathesis copolymerization. J Polym Sci A Polym Chem 39:2920–2928CrossRefGoogle Scholar
  112. Zheng L, Hong S, Cardoen G, Burgaz E, Gido SP, Coughlin EB (2004) Polymer nanocomposites through controlled self-assembly of cubic Silsesquioxane scaffolds. Macromolecules 37:8606–8611CrossRefGoogle Scholar
  113. Zou H, Wu S, Shen J (2008) Polymer/silica nanocomposites: preparation, characterization, properties, and applications. Chem Rev 108:3893–3957CrossRefGoogle Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  • Prasansha Rastogi
    • 1
  • Neha Katiyar
    • 1
  • Swaroop Gharde
    • 1
  • Balasubramanian Kandasubramanian
    • 1
    Email author
  1. 1.Polymer Processing Laboratory, Department of Metallurgical & Materials EngineeringDefence Institute of Advanced Technology (DU), Ministry of DefencePuneIndia

Personalised recommendations