Performance analysis of R134a vapor compression refrigeration system based on CuO/CeO2 mixture nanorefrigerant HudaElslam Abdali MohamedUnal CamdaliMetin Aktas Technical Paper 04 May 2022 Article: 220
Numerical investigation of triangular bluff bodies size effect on heat and mass transfer phenomena: internal flow Davoud Abbasinezhad FallahSajad RezazadehMohammad Raad Technical Paper 03 May 2022 Article: 219
Efficiency and NOx emission optimization by genetic algorithm of a coal-fired steam generator modeled with artificial neural networks Bárbara Pacheco da RochaNatália de Assis Brasil WeberJúlio Cezar Mairesse Siluk Technical Paper 03 May 2022 Article: 218
Optimal earth–moon trajectories in elliptic models: part 2 transfer between elliptic low earth orbit to elliptic low moon orbit Luiz Arthur Gagg FilhoSandro da Silva Fernandes Technical Paper 02 May 2022 Article: 217
A novel current-carrying lubrication in electric hot incremental forming of Ti–6Al–4V titanium sheet Zhengfang LiSonglin HeShihong Lu Technical Paper 02 May 2022 Article: 216
A dynamic estimation-based obstacle avoidance system for AV adapting to various moving directions obstacle Zhixian LiuXiaofang Yuan Technical Paper 02 May 2022 Article: 215
Low-cost solar still with corrugated absorber basin for water desalination Maria Karolina Borba CardosoKaryna Steffane da SilvaCarlos Antônio Pereira de Lima Technical Paper 28 April 2022 Article: 214
Time-varying mesh stiffness model of a modified gear–rack drive with tooth friction and wear Changjiang ZhouXiaojie DongZhongming Liu Technical Paper 28 April 2022 Article: 213
Comparative study of tuning techniques for fractional PID controllers for FOPDT systems Rodrigo Teixeira AguiarBruno Silva de LimaAntônio Augusto Torres Maia Technical Paper 27 April 2022 Article: 212
Research on position/force hybrid control of an FFHD robot with EHS-actuators Yongmei WangXigui WangSiyuan An Technical Paper Open access 27 April 2022 Article: 211
Accuracy of three different versions of flamelet-generated manifold with/without radiation coupling in simulation of pool fire Mohammad SafarzadehGhassem HeidarinejadHadi Pasdarshahri Technical Paper 27 April 2022 Article: 210
Investigating the matching characteristic of the full hydraulic braking system of the wheel loader Peng TanXin-hui LiuTian You Technical Paper 26 April 2022 Article: 209
Fatigue and microhardness of 6201 wire of overhead conductor Layse Mendes DinizGustavo ReinkeCosme Roberto Moreira da Silva Technical Paper 26 April 2022 Article: 208
Optimization for multi-cell thin-walled tubes under quasi-static three-point bending Emre İsa Albak Technical Paper 25 April 2022 Article: 207
A comprehensive multi-objective, multi-parameter and multi-condition optimization of a spiral groove in dry gas seals Cong ZhangJinbo JiangXudong Peng Technical Paper 25 April 2022 Article: 206
Effect of optimum process parameters on material removal in rotational-magnetorheological miniature gear profile polishing (R-MRMGPP) process Manjesh KumarManas DasNan Yu Technical Paper 25 April 2022 Article: 205
Investigation of graphene nanoplatelets-deposited textured metal matrix composite plates for improved mechanical properties: a numerical approach Mridul SinghalAkshat JainAshirbad Swain Technical Paper 25 April 2022 Article: 204
Study on the effect of raindrops on the dynamic stall of a NACA-0012 airfoil Armin SheidaniSajad SalavatidezfouliPaolo Schito Technical Paper Open access 24 April 2022 Article: 203
A novel design-point computational program for thermal power plants applications: energy, exergy and economic (3E) analysis Fabíola Paula CostaCleverson BringhentiJayanta Sankar Kapat Technical Paper 23 April 2022 Article: 202
A practical application of sliding mode control in the motion control of a high precision piezoelectric motor Gangfeng YanKhalid Abidi Technical Paper 23 April 2022 Article: 201
Pressure drop and non-Newtonian behavior of ice slurry in a horizontal pipe F. A. RayhanR. Rizal Technical Paper 23 April 2022 Article: 200
Controlled addition of air in the gas mixture of plasma nitriding: an analysis of nitrided layer microstructure and microhardness of carbon steels Francisco Cavilha NetoTatiana BendoAloisio Nelmo Klein Technical Paper 22 April 2022 Article: 199
A study on the electroosmotic flow of micropolar fluid in a channel with hydrophobic walls Fateme KarampourAmin Haghighi PoshtiriAmin Hadizade Technical Paper 22 April 2022 Article: 198
Numerical study of natural convection of nanofluid in a rectangular closed enclosure (RCE) affected by hot and cold flow in a two-layer microchannel Shahrouz YousefzadehShahram EsmaeiliDavood Toghraie Technical Paper 22 April 2022 Article: 197
An investigation on nonlinear viscoelastic lubrication using FENE-P constitutive equation Melika Mokhtari SharghiMahmood NorouziAli Abbaspur Technical Paper 21 April 2022 Article: 196
Semi-empirical correlations for predicting hot gas layer temperature in pre-flashover compartment fires considering fire source location Calisa Katiuscia LemmertzRodolfo Prediger HelfensteinFelipe Roman Centeno Technical Paper Open access 20 April 2022 Article: 195
Eigenfrequency-based topology optimization using cooperative coevolutionary strategies and moving morphable components Pooya RostamiJavad MarzbanradMohammad Hossein Taghavi Parsa Technical Paper 20 April 2022 Article: 194
Failure criterion for SPIF based on mean stress Rafael Gustavo SchreiberAriton AraldiLirio Schaeffer Technical Paper 20 April 2022 Article: 193
Study on thermal characteristics of the large multi-gasbag airship at low-altitude flight Jingye MengRensheng ZhuBin Huang Letter to the Editor 19 April 2022 Article: 192
The singular boundary method for unilateral contact problems Bin ChenLei ZhangKaiou Shu Technical Paper 17 April 2022 Article: 191
Remaining useful life estimation for aero-engine with multiple working conditions via an improved generative adversarial network Yang GeFusheng Zhang Technical Paper 17 April 2022 Article: 190
New cyclone design based on minimum height and optimized pressure drop and efficiency Pouria Khalili Ata AbadiSaeid Kheradmand Technical Paper 17 April 2022 Article: 189
A hybrid Grey-TOPSIS based quantum behaved particle swarm optimization for selection of electrode material to machine Ti6Al4V by electro-discharge machining Anshuman Kumar SahuSiba Sankar MahapatraSaurav Goel Technical Paper 17 April 2022 Article: 188
Correction to: Accuracy analysis of improved SPH methods for solution of quadratic PDEs representing potential flows and elasticity problems Gholamreza Shobeyri Correction 16 April 2022 Article: 187
A large strain one-dimensional ductile damage model for space truss analysis considering Gurson’s porous plasticity, thermal effects and mixed hardening João Paulo Pascon Technical Paper 14 April 2022 Article: 186
Review on various borehole cleaning parameters related to oil and gas well drilling Vivek DeshmukhSatish Kumar Dewangan Review 13 April 2022 Article: 185
Gas–solid coupling lateral vibration characteristics of high-speed elevator based on blockage ratio Ruijun ZhangJie LiuQin He Technical Paper 13 April 2022 Article: 184
Flexural response of fiber-metal laminate face-sheet/corrugated core sandwich beams N. Bahrami-NovinM. ShabanH. Mazaheri Technical Paper 12 April 2022 Article: 183
Well integrity assessment under uncertainty considerations and evaluation of the workover frequency impact Danilo ColomboDanilo Taverna Martins Pereira de AbreuGilson Brito Alves Lima Technical Paper 12 April 2022 Article: 182
New insights into the mixing behavior of Non-Newtonian fluid in electroosmotic micromixer Honglin LvXueye Chen Technical Paper 12 April 2022 Article: 181
The effect of carbon dioxide on the reactivity of H2/CO oxy-fuel combustion Javier Ordoñez-LozaCarlos GomezFarid Chejne Review 12 April 2022 Article: 180
Experimental parametric analysis of biodiesel synthesis in microreactors using waste cooking oil (WCO) in ethilic route Saxon PaizJosé Martim Costa JuniorCarolina Palma Naveira-Cotta Review 11 April 2022 Article: 179
Feasibility and performance analyses for an active geometry control suspension system for over-actuated vehicles Fernando MalvezziTarcisio Antonio Hess CoelhoRenato Maia Matarazzo Orsino Technical Paper 10 April 2022 Article: 178
New positional accuracy calibration method for an autonomous robotic inspection system Geng ChenJianzhong YangDaojiang Ou Technical Paper 09 April 2022 Article: 177
Effects of high viscosity ratio and interfacial tension on droplet formation Kazem Rayatdoost TalookiElham Omidbakhsh AmiriHamed Salimi-Kenari Technical Paper 09 April 2022 Article: 176
Thermal analysis of disk-type transformer winding immersed in nanofluids using mixture and Eulerian–Lagrangian approach Ali Asghar TaheriAli MaboudiMohammad Taghilou Technical Paper 08 April 2022 Article: 175
Nonlinear dynamic response dissipation of plates with heterogeneous orthotropic distributions of shape memory alloy micro-wires undergoing 3D phase-transformations M. Shariyat Technical Paper 07 April 2022 Article: 174
Strain gradient bistability of bimorph piezoelectric curved beam interacting with a curved electrode Yasaman GhalamiAmir R. AskariMasoud Tahani Technical Paper 07 April 2022 Article: 173
Comparative study of arterial wall models for numerical fluid–structure interaction simulation of aortic arch aneurysms Mário Luis Ferreira da SilvaSaulo de Freitas GonçalvesRudolf Huebner Technical Paper 07 April 2022 Article: 172
Modeling of hydrodynamic bearings with a novel boundary parameterization approach J. A. MotaD. J. G. MaldonadoT. G. Ritto Technical Paper 07 April 2022 Article: 171