Mechanical responses of maxillary canine and surrounding tissues under orthodontic loading: a non-linear three-dimensional finite element analysis Mohammad RoostaieM. Soltani Technical Paper 11 January 2017 Pages: 2353 - 2369
Estimation of bovine pelvic limb inertial properties using an elliptical model Leopoldo Augusto PaolucciLuciana de Melo GomidesHans Menzel Technical Paper 21 February 2017 Pages: 2371 - 2382
Simultaneous dynamic optimization of valves timing and waste gate to improve the load step transient response of a turbocharged spark ignition engine Amir-Hasan KakaeeMehdi Keshavarz Technical Paper 12 April 2017 Pages: 2383 - 2394
The impact of C/H on the radiative and thermal behavior of liquid fuel flames and pollutant emissions Mehdi BoghratiMohammad MoghimanSeyed Hadi Pourhoseini Technical Paper 11 May 2017 Pages: 2395 - 2403
Model-based single fault disambiguation and fault tolerant control for a hydraulic drive using receding horizon Sarnendu PaulSanjoy K. GhoshalJayanta Das Technical Paper 14 March 2017 Pages: 2405 - 2419
Prediction of the overall noise level of DI diesel engine with calculated in-cylinder pressure Zhiyong HaoQinghui ZhangWenying Yang Technical Paper 16 September 2016 Pages: 2421 - 2432
Experimental evaluation of a fuzzy logic controller on a quarter car test rig Yener TaskinYuksel HaciogluNurkan Yagiz Technical Paper 21 September 2016 Pages: 2433 - 2445
Numerical investigation on the dynamic behavior of an onboard rotor system by using the FEM approach M. S. Sousa Jr.V. T. S. Del ClaroV. Steffen Jr. Technical Paper 24 October 2016 Pages: 2447 - 2458
Effect of grouser height on tractive performance of tracked mining vehicle Junzheng LiShaojun LiuYu Dai Technical Paper 28 September 2016 Pages: 2459 - 2466
Simulation of wind-generated surface waves and effects of bubbles on scattering, transmission, and attenuation of low frequency sound at the sea surface Parviz GhadimiMohammad A. Feizi CheckabAlireza Bolghasi Technical Paper 19 November 2016 Pages: 2467 - 2486
Mathematical modeling of blood flow through a stenosed artery under body acceleration Ahmad Reza HaghighiSoraya Asadi Chalak Technical Paper 31 January 2017 Pages: 2487 - 2494
The effect of slip condition on the three-dimensional flow of Jeffrey fluid along a plane wall with periodic suction M. ShoaibM. A. RanaA. M. Siddiqui Technical Paper 03 February 2017 Pages: 2495 - 2503
An analytical model for simulating air concentration in drop and deflector jets Roghayeh AhmadpourHamed SarkardehS. Amin Salamatian Technical Paper 04 February 2017 Pages: 2505 - 2517
Numerical study of vortex shedding suppression and aerodynamic characteristics of three obstacle configurations having two shapes Salwa FezaiNader Ben-CheikhTaieb Lili Technical Paper 09 February 2017 Pages: 2519 - 2534
Impinging of metallic nanoparticles along with the slip effects through a porous medium with MHD Iqra shahzadiS. Nadeem Review 09 February 2017 Pages: 2535 - 2560
A mixed-flow submersible well pump: design features and an investigation of performance Qihua ZhangYuanhui XuWeigang Lu Technical Paper 08 February 2017 Pages: 2561 - 2569
Influence of heat transfer on the peristaltic transport of Walters B fluid in an inclined annulus K. RameshM. Devakar Technical Paper 10 April 2017 Pages: 2571 - 2584
Numerical simulation of needle movement nozzle flow coupled with spray for a diesel injector using an Eulerian spray atomization model Raúl PayriJaime GimenoMary Alarcón Technical Paper 09 May 2017 Pages: 2585 - 2592
Review of research work in die sinking EDM for machining curved hole D. B. MeshramY. M. Puri Review 23 August 2016 Pages: 2593 - 2605
An adaptive loading path design method for tube hydroforming using fuzzy logic theory Yu-long GeXiao-xing LiShangwen Ruan Technical Paper 23 August 2016 Pages: 2607 - 2617
Application of a hybrid Taguchi-entropy weight-based GRA method to optimize and neural network approach to predict the machining responses in ultrasonic machining of Ti–6Al–4V Gaurav Kumar DhuriaRupinder SinghAjay Batish Technical Paper 25 August 2016 Pages: 2619 - 2634
Investigating surface properties of cryogenically treated titanium alloys in powder mixed electric discharge machining Sanjeev KumarRupinder SinghRajdeep Singh Technical Paper 26 September 2016 Pages: 2635 - 2648
Surface integrity of bored super duplex stainless steel SAF 2507 Fernando MoreloMarina Izabelle GrabarskiGiuseppe Pintaude Technical Paper 04 October 2016 Pages: 2649 - 2658
Kinematics-based approach for robot programming via human arm motion Abhishek JhaShital S. ChiddarwarMayur V. Andulkar Technical Paper 28 October 2016 Pages: 2659 - 2675
RETRACTED ARTICLE: Theoretical research of self-excited oscillations in transmitters for auxiliary motion of a tool machine using a nonlinear model Milan CvetkovićSlavica Cvetković Technical Paper 27 February 2017 Pages: 2677 - 2686
Numerical simulation of 1-D oil and water displacements in petroleum reservoirs using the spectral finite volume method G. Galindez-RamirezM. R. A. SouzaP. R. M. Lyra Technical Paper 08 May 2017 Pages: 2687 - 2700
Study on the roller enveloping end face internal engagement worm gear L. ZhengX. DengG. Yin Technical Paper 01 March 2017 Pages: 2701 - 2711
Influences of chemical characteristics and nanoadditive participation on raw vegetable oils’ tribological properties Dan MoldovanuFlorin Mariasiu Technical Paper 28 February 2017 Pages: 2713 - 2720
Crashworthiness multi-objective optimization of the thin-walled grooved conical tubes filled with polyurethane foam Batool SarkabiriAli JahanMohammad Javad Rezvani Technical Paper 09 March 2017 Pages: 2721 - 2734
Experimental investigation on waste heat driven activated carbon-methanol adsorption cooling system Anirban SurRandip K. Das Technical Paper 27 April 2017 Pages: 2735 - 2746
Computational study of non-Newtonian Eyring–Powell fluid from a vertical porous plate with biot number effects S. Abdul GaffarV. Ramachandra PrasadBhuvana Vijaya Technical Paper 22 March 2017 Pages: 2747 - 2765
High-frequency storage and loss moduli estimation for an electromagnetic rheological fluid using Fredholm integral equations of first kind and optimization methods Nader MohammadiNasrin KamalianRambod Rastegari Technical Paper 23 May 2017 Pages: 2767 - 2777
Structural optimization research on superstructure of jib crane Shu LiChun-Feng WanZhixiang Hou Technical Paper 04 February 2017 Pages: 2779 - 2787
Size-dependent vibration of sandwich cylindrical nanoshells with functionally graded material based on the couple stress theory Hamid ZeighampourMilad Shojaeian Technical Paper 31 March 2017 Pages: 2789 - 2800
Analysis of multilayered composite plates resting on elastic foundations in thermal environment using a hyperbolic model A. M. ZenkourA. F. Radwan Technical Paper 04 April 2017 Pages: 2801 - 2816
Buckling analysis of coupled DLGSs systems resting on elastic medium using sinusoidal shear deformation orthotropic plate theory Mehdi Khajehdehi KavanroodiAbdolhossein FereidoonAli Reza Mirafzal Technical Paper 21 April 2017 Pages: 2817 - 2829
MHD natural convection phase-change heat transfer in a cavity: analysis of the magnetic field effect Ali DoostaniMohammad GhalambazAli J. Chamkha Technical Paper 08 February 2017 Pages: 2831 - 2846
Coupled radiative-conductive heat transfer problems in complex geometries using embedded boundary method Milad ZabihiKhosro LariHossein Amiri Technical Paper 13 February 2017 Pages: 2847 - 2864
A multi-nets ANN model for real-time performance-based automatic fault diagnosis of industrial gas turbine engines Mohammadreza TahanMasdi MuhammadZ. A. Abdul Karim Technical Paper 16 March 2017 Pages: 2865 - 2876
Developing of ANN model for prediction of performance and emission characteristics of VCR engine with orange oil biodiesel blends V. KarthickeyanP. BalamuruganR. Senthil Technical Paper 29 March 2017 Pages: 2877 - 2888
Hybrid solution for the flow and heat transfer of a second-grade viscoelastic fluid on a stretching sheet with injection or suction Marcelo J. R. SouzaEmanuel N. MacêdoJoão N. N. Quaresma Technical Paper 05 April 2017 Pages: 2889 - 2904
A gradient-based polynomial chaos approach for risk and reliability-based design optimization A. J. ToriiR. H. LopezL. F. F. Miguel Technical Paper 29 May 2017 Pages: 2905 - 2915