1. Nonuniform loading representation for structural optimization considering convex objective functions

   • A. P. C. S. Ferreira
   • M. V. Toregiani

   Technical Paper 20 January 2014 Pages: 433 - 441

   

2. Fuzzy logic model for the prediction failure analysis of composite plates under various cure temperatures

   • Tamer Ozben
   • Mesut Huseyinoglu
   • Nurettin Arslan

   Technical Paper 23 September 2013 Pages: 443 - 448

   

3. Evaluation of stiffness and strength in fused deposition sandwich specimens

   • L. C. Magalhães
   • N. Volpato
   • M. A. Luersen

   Technical Paper 19 October 2013 Pages: 449 - 459

   

4. Influence of groove shape on clearance in four-point-contact slewing bearing

   • Long Chen
   • Zheng Guo Li
   • Xin-tao Xia

   Technical Paper 05 December 2013 Pages: 461 - 467

   

5. Study of ECAE mechanics by upper bound rigid block model with two degrees of freedom

   • Alexander V. Perig
   • Alexander M. Laptev

   Technical Paper 21 December 2013 Pages: 469 - 476

   

6. Determination of load capacity of a non-gasketed flange joint under combined internal pressure, axial and bending loading for safe strength and sealing

   • Muhammad Abid
   • Abdul Waheed Awan
   • David H. Nash

   Technical Paper 18 February 2014 Pages: 477 - 490

   

7. Mechanical model of the recovery reaction from stumbling: effect of step length on trunk control

   • A. Forner-Cordero
   • HFJM Koopman
   • FCT van der Helm

   Technical Paper 24 January 2014 Pages: 491 - 500

   

8. Development and analysis of series elastic actuators for impedance control of an active ankle–foot orthosis

   • Bruno Jardim
   • Adriano A. G. Siqueira

   Technical Paper 22 December 2013 Pages: 501 - 510

   

9. Investigation on stator vibration characteristics under air-gap eccentricity and rotor short circuit composite faults

   • Gui-Ji Tang
   • Yu-Ling He
   • Ling Xiang

   Technical Paper 29 January 2014 Pages: 511 - 522

   

10. Identification of nonlinear structures using discrete-time Volterra series

    • Sidney Bruce Shiki
    • Vicente Lopes Jr
    • Samuel da Silva

    Technical Paper 31 August 2013 Pages: 523 - 532

    

11. Dynamic and phenomenological vibration models for failure prediction on planet gears of planetary gearboxes

    • Juan Pablo Torregrosa Koch
    • Cristián Molina Vicuña

    Technical Paper 15 February 2014 Pages: 533 - 545

    

12. Concomitant vortex-induced vibration experiments: a cantilevered flexible cylinder and a rigid cylinder mounted on a leaf-spring apparatus

    • Guilherme Rosa Franzini
    • Celso P. Pesce
    • Adriano A. P. Pereira

    Technical Paper 08 October 2013 Pages: 547 - 558

    

13. Experimental evaluation of ship squat in shallow waters

    • Mohammadreza Fathi Kazerooni
    • Mohammad Saeed Seif

    Technical Paper 07 December 2013 Pages: 559 - 569

    

14. Improving Khangiran gas turbine efficiency by two standard and one novel inlet air cooling method

    • Mahdi Deymi-Dashtebayaz
    • Mahmood Farzaneh-Gord
    • Hadi Akeififar

    Technical Paper 12 September 2013 Pages: 571 - 582

    

15. Effects of the number of tangential passages on spray characteristics of a bipropellant atomizer

    • Alexandre Alves
    • Pedro Teixeira Lacava
    • Cristiane Aparecida Martins

    Technical Paper 15 November 2013 Pages: 583 - 590

    

16. On the application of SUPG/θ-method in 2D advection–diffusion-reaction simulation

    • Rômulo Correa Lima
    • André Luis Amarante Mesquita
    • Yves Secretan

    Technical Paper 28 September 2013 Pages: 591 - 603

    

17. Guideline tool based on design for manufacturing and assembly (DFMA) methodology for application on design and manufacturing of aircrafts

    • G. F. Barbosa
    • J. Carvalho

    Technical Paper 17 September 2013 Pages: 605 - 614

    

18. Effects of process parameters on surface roughness in saw cutting of polypropylene/TiO₂ nano composites

    • Mirigul Altan
    • Alper Uysal
    • Erhan Altan

    Technical Paper 06 September 2013 Pages: 615 - 621

    

19. Surface integrity of moulds for microcomponents manufactured by micromilling and electro-discharge machining

    • Sabrina Bodziak
    • Adriano Fagali de Souza
    • Reginaldo Teixeira Coelho

    Technical Paper 26 October 2013 Pages: 623 - 635

    

20. Electrical discharge machining parameters optimization using response surface methodology and fuzzy logic modeling

    • S. Prabhu
    • M. Uma
    • B. K. Vinayagam

    Technical Paper 22 October 2013 Pages: 637 - 652

    

21. Optimization of tribological parameters for a brake pad using Taguchi design method

    • Ferit Ficici
    • Mesut Durat
    • Murat Kapsiz

    Technical Paper 05 November 2013 Pages: 653 - 659