1. Forward and reverse mappings of the cement-bonded sand mould system using fuzzy logic

   • B. Surekha
   • Pandu R. Vundavilli
   • M. B. Parappagoudar

   ORIGINAL ARTICLE 24 November 2011 Pages: 843 - 854

2. A note on “Selection of cutting parameters in side milling operation using graph theory and matrix approach”

   • R. Venkata Rao

   ORIGINAL ARTICLE 24 November 2011 Pages: 855 - 858

3. Influence of slab milling process parameters on surface integrity of HSLA: a multi-performance characteristics optimization

   • Pankul Goel
   • Zahid A. Khan
   • Rajeev Kumar Gupta

   ORIGINAL ARTICLE 22 November 2011 Pages: 859 - 871

4. Vibration-assisted filling capability in thin wall investment casting

   • Waleed Abdul-Karem
   • N. Green
   • Khalid F. Al-Raheem

   ORIGINAL ARTICLE 04 December 2011 Pages: 873 - 887

5. Wear study of Ni–WC composite coating modified with CeO₂

   • Satpal Sharma

   ORIGINAL ARTICLE 02 December 2011 Pages: 889 - 900

6. Influence of deformation path change on static strain aging of cold rolled steel strip

   • Behrad Koohbor
   • Siamak Serajzadeh

   ORIGINAL ARTICLE 04 December 2011 Pages: 901 - 909

7. Load bearing capacity of tool pin during friction stir welding

   • A. Arora
   • M. Mehta
   • T. DebRoy

   ORIGINAL ARTICLE 30 November 2011 Pages: 911 - 920

8. Erratum to: Load bearing capacity of tool pin during friction stir welding

   • A. Arora
   • M. Mehta
   • T. DebRoy

   Erratum 11 May 2012 Pages: 921 - 921

9. Vision inspection system for the identification and classification of defects in MIG welding joints

   • G. Senthil Kumar
   • U. Natarajan
   • S. S. Ananthan

   ORIGINAL ARTICLE Open access 09 December 2011 Pages: 923 - 933

10. On properties at interfaces of friction welded near-nanostructured Al 5083 alloys

    • Mumin Sahin
    • N. Balasubramanian
    • Kaan Ozel

    ORIGINAL ARTICLE 29 November 2011 Pages: 935 - 943

11. Modelling micro geometrical profiles in fused deposition process

    • A. Boschetto
    • V. Giordano
    • F. Veniali

    ORIGINAL ARTICLE 19 November 2011 Pages: 945 - 956

12. Experimental investigation on the influence of electrochemical micro-drilling by short pulsed voltage

    • Zhi-Wen Fan
    • Lih-Wu Hourng
    • Ming-Yuan Lin

    ORIGINAL ARTICLE 27 November 2011 Pages: 957 - 966

13. Process parameter selection for selective laser melting of Ti6Al4V based on temperature distribution simulation and experimental sintering

    • Bo Song
    • Shujuan Dong
    • Christian Coddet

    ORIGINAL ARTICLE 08 December 2011 Pages: 967 - 974

14. Softness abrasive flow method oriented to tiny scale mold structural surface

    • Chen Li
    • Shi-Ming Ji
    • Da-Peng Tan

    ORIGINAL ARTICLE 03 August 2012 Pages: 975 - 987

15. Polishing of the aluminum sheets with magnetic abrasive finishing method

    • Mehrdad Givi
    • Alireza Fadaei Tehrani
    • Aminollah Mohammadi

    ORIGINAL ARTICLE 02 December 2011 Pages: 989 - 998

16. ERP: a literature survey

    • Eslam Nazemi
    • Mohammad Jafar Tarokh
    • G. Reza Djavanshir

    ORIGINAL ARTICLE 25 February 2012 Pages: 999 - 1018

17. Development of an algorithm for optimum control process to compensate the nozzle wear effect in cutting the hard and tough material using abrasive water jet cutting process

    • Mehdi Zohoor
    • S. Hadi Nourian

    ORIGINAL ARTICLE 27 November 2011 Pages: 1019 - 1028

18. Development and characterization of a novel piezoelectric-driven stick-slip actuator with anisotropic-friction surfaces

    • Q. S. Zhang
    • X. B. Chen
    • W. J. Zhang

    ORIGINAL ARTICLE 09 December 2011 Pages: 1029 - 1034

19. Deformation and stress of a composite–metal assembly

    • Chensong Dong
    • Lu Kang

    ORIGINAL ARTICLE 20 November 2011 Pages: 1035 - 1042

20. Composite fabrication using friction stir processing—a review

    • H. S. Arora
    • H. Singh
    • B. K. Dhindaw

    ORIGINAL ARTICLE 04 December 2011 Pages: 1043 - 1055

21. Adaptive nonlinear contour coupling control for a machine tool system

    • Jinho Lee
    • Warren E. Dixon
    • John C. Ziegert

    Original Article 04 December 2011 Pages: 1057 - 1065

22. Optimization of variable blank holder force trajectory by sequential approximate optimization with RBF network

    • Satoshi Kitayama
    • Kenta Kita
    • Koetsu Yamazaki

    ORIGINAL ARTICLE 24 November 2011 Pages: 1067 - 1083

23. ISO manufacturing tolerancing: three-dimensional transfer with analysis line method

    • Bernard Anselmetti

    ORIGINAL ARTICLE 08 December 2011 Pages: 1085 - 1099

24. A genetic algorithm and particle swarm optimization for no-wait flow shop problem with separable setup times and makespan criterion

    • Hamed Samarghandi
    • Tarek Y. ElMekkawy

    ORIGINAL ARTICLE 25 November 2011 Pages: 1101 - 1114

25. Non-identical parallel machine scheduling with fuzzy processing times using genetic algorithm and simulation

    • Savaş Balin

    ORIGINAL ARTICLE 02 December 2011 Pages: 1115 - 1127

26. Scheduling in a two-machine flow-shop for earliness/tardiness under learning effect

    • Mesut Cemil İşler
    • Bilal Toklu
    • Veli Çelik

    ORIGINAL ARTICLE 02 December 2011 Pages: 1129 - 1137

27. Analysis of partial trade credit financing in a supply chain by EOQ-based model for decaying items with shortages

    • Karuppuchamy Annadurai
    • Ramasamy Uthayakumar

    Original Article Open access 11 December 2011 Pages: 1139 - 1159

28. A DEA approach for comparing solution efficiency in U-line balancing problem using goal programming

    • Hami Farkhondeh
    • Reza Hassanzadeh
    • Nezam Mahdavi-Amiri

    ORIGINAL ARTICLE 25 December 2011 Pages: 1161 - 1172

29. Editorial: Micromachining

    • V. K. Jain
    • P. K. Jain
    • P. V. Rao

    EDITORIAL 04 July 2012 Pages: 1173 - 1174

30. Fabrication of micro-features and micro-tools using electrochemical micromachining

    • V. K. Jain
    • Subodh Kalia
    • V. N. Kulkarni

    ORIGINAL ARTICLE 18 April 2012 Pages: 1175 - 1183

31. Drilling of micro-holes on copper using electrochemical micromachining

    • R. Thanigaivelan
    • R. M. Arunachalam
    • Pelden Drukpa

    ORIGINAL ARTICLE 05 April 2012 Pages: 1185 - 1190

32. A study on micro machining of e-glass–fibre–epoxy composite by ECSM process

    • Alakesh Manna
    • Vivek Narang

    ORIGINAL ARTICLE 12 April 2012 Pages: 1191 - 1197

33. On wire breakage and microstructure in WEDC of SiC_p/6061 aluminum metal matrix composites

    • Pragya Shandilya
    • P. K. Jain
    • N. K. Jain

    ORIGINAL ARTICLE 14 April 2012 Pages: 1199 - 1207

34. A feasibility approach by simulated annealing on optimization of micro-wire electric discharge machining parameters

    • K. P. Somashekhar
    • Jose Mathew
    • N. Ramachandran

    ORIGINAL ARTICLE 14 April 2012 Pages: 1209 - 1213

35. Manufacture of micro sized threads for micro actuator of laser grating mount

    • Gopi Krishna S.
    • Raju V. R.
    • Shashikumar P. V.

    ORIGINAL ARTICLE 09 May 2012 Pages: 1215 - 1220

36. An optimisation of micro-EDM operation for fabrication of micro-hole

    • K. P. Maity
    • Ravi Kumar Singh

    ORIGINAL ARTICLE 28 April 2012 Pages: 1221 - 1229

37. Simultaneous optimisation of multiple performance characteristics in micro-EDM drilling of titanium alloy

    • M. S. Azad
    • A. B. Puri

    ORIGINAL ARTICLE 13 April 2012 Pages: 1231 - 1239

38. Electrothermal theory approach for numerical approximation of the μ-EDM process

    • K. P. Somashekhar
    • Jose Mathew
    • N. Ramachandran

    ORIGINAL ARTICLE 12 April 2012 Pages: 1241 - 1246

39. Process modeling of hybrid machining system consisted of electro discharge machining and end milling

    • Jean Bosco Byiringiro
    • Min Yeop Kim
    • Tae Jo Ko

    ORIGINAL ARTICLE 18 April 2012 Pages: 1247 - 1254

40. Hole characteristics optimization in Nd:YAG laser micro-drilling of zirconium oxide by grey relation analysis

    • D. Ganguly
    • B. Acherjee
    • S. Mitra

    ORIGINAL ARTICLE 15 April 2012 Pages: 1255 - 1262

41. Simulation of surface generated during abrasive flow finishing of Al/SiC_p-MMC using neural networks

    • Harlal Singh Mali
    • Alakesh Manna

    ORIGINAL ARTICLE 04 April 2012 Pages: 1263 - 1268

42. Case-based reasoning (CBR) model for hard machining process

    • Anthony M. Xavior
    • Margret S. Anouncia

    ORIGINAL ARTICLE 18 April 2012 Pages: 1269 - 1275