Research on water jet-guided laser micro-hole machining of 6061 aluminum alloy Yinuo ZhangHongchao QiaoZhihe Cao ORIGINAL ARTICLE 23 April 2021 Pages: 1 - 13
Analysis of the stress-strain state of steel closed ropes under tension and torsion Leonid GurevichVladimir DanenkoVitaliy Kulevich ORIGINAL ARTICLE 27 April 2021 Pages: 15 - 22
A method for obtaining the fraction of absorbed energy of material based on laser shock processing experiment and simulation Jiajun WuJibin ZhaoZheng Huang ORIGINAL ARTICLE 03 May 2021 Pages: 23 - 31
MWCNTs doped GFRPs drilling: crosscheck among holes obtained by alternative manufacturing methods Ferhat CeritbinmezVildan Ă–zkanAhmet Yapici ORIGINAL ARTICLE 06 May 2021 Pages: 33 - 41
Precision polishing of the mandrel for X-ray grazing incidence mirrors Fuchang ZuoLiansheng LiJianwu Chen ORIGINAL ARTICLE 11 May 2021 Pages: 43 - 53
Formability and interface structure of Al/Mg/Al composite sheet rolled by hard-plate rolling (HPR) Peng Da HuoFeng LiXing Mao Xiao ORIGINAL ARTICLE 12 May 2021 Pages: 55 - 65
Parametric and non-parametric methods for monitoring nonlinear fuzzy profiles Mohammadreza Nasiri BoroujeniYaser SamimiEmad Roghanian ORIGINAL ARTICLE 18 May 2021 Pages: 67 - 84
Influence of laser parameters on processing microgrooves of 2.5-dimensional C/SiC composites via nanosecond laser Haowen JiaoBing ChenZhaohui Deng ORIGINAL ARTICLE 28 May 2021 Pages: 85 - 101
Effect of different parameters on the tensile properties of printed Polylactic acid samples by FDM: experimental design tested with MDs simulation Ashkan FarazinMohammadimehr Mehdi ORIGINAL ARTICLE 31 May 2021 Pages: 103 - 118
Advanced information technology for development of electric power market Valentin AfanasyevVsevolod ChernyshenkoVardan Mkrttchian ORIGINAL ARTICLE 04 June 2021 Pages: 119 - 127
CFD researches of centrifugal compressor stage vane diffusers in interests of math modeling Aleksey BorovkovYuri GalerkinLyubov Marenina ORIGINAL ARTICLE 03 July 2021 Pages: 129 - 141
Comparative analysis of high carbon steel behavior on contact surface with a tool in different methods of deformational nanostructuring Marina A. PolyakovaAleksandr E. GulinOksana V. Nikiforova ORIGINAL ARTICLE 21 July 2021 Pages: 143 - 154
Study on discharge point distribution of finishing in high-speed wire electrical discharge machine based on potential difference method Haihui WuTong WangJunqi Wang ORIGINAL ARTICLE 30 August 2021 Pages: 155 - 172
Manufacture of centrifugal compressor impeller using FDM and investment casting Chol-Min ChoeWon-Chol YangMyong-Song Om ORIGINAL ARTICLE 03 September 2021 Pages: 173 - 181
Sliding abrasive wear when combining WEDM conditions and polishing treatment on H13 disks over 1045 carbon steel pins Antonio J. Sánchez EgeaVitaliy MartynenkoDaniel MartĂnez Krahmer ORIGINAL ARTICLE Open access 03 September 2021 Pages: 183 - 193
Design and performance evaluation of multi-helical springs fabricated by Multi Jet Fusion additive manufacturing technology Ahmad Bin ArshadAamer NazirJeng-Ywan Jeng ORIGINAL ARTICLE 03 September 2021 Pages: 195 - 206
Numerical simulation of convex shape beam spot on stress field of plasma-sprayed MCrAlY coating during laser cladding process Peipei ZhangJiaqing ChuDongsheng Wang ORIGINAL ARTICLE 03 September 2021 Pages: 207 - 217
Correction to: Numerical simulation of convex shape beam spot on stress field of plasma-sprayed MCrAlY coating during laser cladding process Peipei ZhangJiaqing ChuDongsheng Wang Correction 09 November 2021 Pages: 219 - 219
Study on forming limit of single-point progressive forming of AZ31B magnesium alloy under isothermal local loading Chunjian SuMingyu ZhangRui Wang ORIGINAL ARTICLE 04 September 2021 Pages: 221 - 236
Experimental and analytical study of ultrasonic elliptical vibration cutting of micro-pyramid reflective mold based on guided wave transmission Tao JiangJintao YangJun Zhang ORIGINAL ARTICLE 04 September 2021 Pages: 237 - 253
Identification method for the dynamic distribution characteristics of machining errors in high energy efficiency milling Jiang BinFan LiliZhao Junfeng ORIGINAL ARTICLE 04 September 2021 Pages: 255 - 274
Thermal influence analysis of coatings and contact resistance in turning cutting tool using COMSOL Carlos A. CorrĂŞa RibeiroJoĂŁo R. FerreiraSandro M. M. Lima e Silva ORIGINAL ARTICLE 04 September 2021 Pages: 275 - 289
The influence of electrode hole structure on cross groove electrochemical machining Yuanlong ChenHua LinQi Chen ORIGINAL ARTICLE 05 September 2021 Pages: 291 - 301
Simulation and experimental study of the ground surface topography of GH4169 by grains arrayed brazed diamond wheels Wentao WangQuanli ZhangJiuhua Xu ORIGINAL ARTICLE 05 September 2021 Pages: 303 - 317
Finite Element Investigation of Thermal-kinetic-mechanical Evolutions during Laser Powder Deposition as an Innovative Technique for Rail Repair Ershad MortazavianZhiyong WangHualiang Teng ORIGINAL ARTICLE 05 September 2021 Pages: 319 - 342
Microstructure, mechanical, and corrosion properties of electron beam-welded commercially pure titanium after laser shock peening Angshuman ChattopadhyayGopinath MuvvalaAshish Kumar Nath ORIGINAL ARTICLE 05 September 2021 Pages: 343 - 364
Determination of the optimal coverage for heavy-duty-axle gears in shot peening Hongzhi YanPengfei ZhuYu Zhang ORIGINAL ARTICLE 05 September 2021 Pages: 365 - 376
Investigation of the polishing mechanism of magnetorheological elastic polishing composites Zhiqiang XuJun WangShengqiang Jiang ORIGINAL ARTICLE 05 September 2021 Pages: 377 - 389
Improving RT-WEDM performance with a radio frequency signal monitoring system Zi-Lun LiXue-Cheng XiWan-Sheng Zhao ORIGINAL ARTICLE 05 September 2021 Pages: 391 - 404
Evaluation of the formability of AA2198-T3 Al-Li alloy in warm sheet hydroforming Hui WangSijia ChengXunzhong Guo ORIGINAL ARTICLE 05 September 2021 Pages: 405 - 416
Prediction of tensile strength and assessing the influence of process parameters of magnetically impelled arc butt welded AISI 409 ferritic stainless steel tubes Thiyagarajan Muthu KrishnanIsaac DinaharanChinnasamy Balamurugan ORIGINAL ARTICLE 06 September 2021 Pages: 417 - 432
Numerical analysis of the performance of half oval micro-textured/grooved cutting tool in machining of Ti-6Al-4V Xin LiuXu Zhang ORIGINAL ARTICLE 06 September 2021 Pages: 433 - 447
Research on the excitation characteristics of milling force for a general helix cutter Xing ZhangLei YangJia Yin ORIGINAL ARTICLE 06 September 2021 Pages: 449 - 464
A GPS-based force rendering model for virtual assembly of mechanical parts Yongpeng YuQinghui WangJingrong Li ORIGINAL ARTICLE 06 September 2021 Pages: 465 - 477
Novel polishing media based on fiber for finishing hip joint implants Yahya ChoopaniMohsen KhajehzadehMohammad Reza Razfar ORIGINAL ARTICLE 06 September 2021 Pages: 479 - 495
Influencing factors of effective tooth depth in the cylindrical gear rolling process with axial infeed Youxin LuoZiyong MaYuanxin Luo ORIGINAL ARTICLE 07 September 2021 Pages: 497 - 510
Evaluation of subcooled MQL in cBN hard turning of powder-based Cr-Mo-V tool steel using simulations and experiments Sampsa V.A. LaaksoDinesh MallipeddiPeter Krajnik ORIGINAL ARTICLE Open access 07 September 2021 Pages: 511 - 531
Investigation of crucial geometric errors of screw grinder for ball screw profile parameters Yi OuYong-Sheng XingHu-Tian Feng ORIGINAL ARTICLE 07 September 2021 Pages: 533 - 550
Contour error modeling and compensation of CNC machining based on deep learning and reinforcement learning Yakun JiangJihong ChenJunxiang Wang ORIGINAL ARTICLE 07 September 2021 Pages: 551 - 570
Tool orientation optimization method based on ruled surface using genetic algorithm Zheng GongBingran LiPeiqing Ye ORIGINAL ARTICLE 07 September 2021 Pages: 571 - 584
Investigation of tool-workpiece contact rate and milling force in elliptical ultrasonic vibration-assisted milling Zongyuan LiLida ZhuWenbin Cao ORIGINAL ARTICLE 07 September 2021 Pages: 585 - 601
A critical review on the environmental impact of manufacturing: a holistic perspective Vasiliki Christina PanagiotopoulouPanagiotis StavropoulosGeorge Chryssolouris ORIGINAL ARTICLE Open access 07 September 2021 Pages: 603 - 625
Modeling and analysis of the material removal rate for ultrasonic vibration–assisted polishing of optical glass BK7 Yingdong LiangChao Zhang Ji Zhao ORIGINAL ARTICLE 07 September 2021 Pages: 627 - 639
Study on surface residual stress of hardened 12Cr2Ni4A alloy steel by ultrasonic vibration-assisted ELID grinding Xiaofei LeiDaohui XiangGuofu Gao Application 06 July 2021 Pages: 641 - 649
A kinesthetic teaching approach for automating micropipetting repetitive tasks Cláudia RochaJoana DiasPedro Costa Application 07 September 2021 Pages: 651 - 663
Correction to: Formability enhancement of 5052 aluminium alloy sheet in electromagnetic impaction forming Fei FengJianjun LiShijing Cao Correction 18 November 2021 Pages: 665 - 665