1. Insights into the fatigue property of titanium alloy Ti-6Al-4V in aero-engine from the subsurface damages induced by milling: state of the art

   • Ning Hou
   • Minghai Wang
   • Ce Song

   Critical Review 11 February 2021 Pages: 1229 - 1235

   

2. Ultrasonic nanocrystalline surface modification of low strength aluminum alloy: trade-off between surface integrity and production rate aiming at desired fatigue life

   • Reza Bagherian Azhiri
   • Aydin Jadidi
   • Mostafa Rahimi Dizadji

   ORIGINAL ARTICLE 21 January 2021 Pages: 1237 - 1251

   

3. Correction to: “Ultrasonic nanocrystalline surface modification of low strength aluminum alloy: trade-off between surface integrity and production rate aiming at desired fatigue life”

   • Reza Bagherian Azhiri
   • Aydin Jadidi
   • Mostafa Rahimi Dizadji

   Correction 21 February 2021 Pages: 1253 - 1253

4. Performance analysis of the longitudinal-torsional ultrasonic milling of Ti-6Al-4V

   • Yu Pang
   • Pingfa Feng
   • Jie Xu

   ORIGINAL ARTICLE 02 February 2021 Pages: 1255 - 1266

   

5. Finite element analysis of orthogonal cutting of cellular metals: influence of cutting conditions on chip formation and surface damage

   • Rafael Guerra-Silva
   • Uwe Teicher
   • Arístides González-Zamora

   ORIGINAL ARTICLE 02 February 2021 Pages: 1267 - 1280

   

6. Grinding comparative analysis between different proportions of water-oil applied to MQL technique and industrial production cost towards a green manufacturing

   • José Claudio Lopes
   • Benício Nacif Ávila
   • Eduardo Carlos Bianchi

   ORIGINAL ARTICLE 03 February 2021 Pages: 1281 - 1293

   

7. Empowering Digital Twin for Industry 4.0 using metaheuristic optimization algorithms: case study PCB drilling optimization

   • David Balderas
   • Alexandro Ortiz
   • Arturo Molina

   ORIGINAL ARTICLE 03 February 2021 Pages: 1295 - 1306

   

8. Theoretical analysis and performance prediction on modified surface layer caused by ultrasonic surface rolling

   • Zhihua Liu
   • Chenhui Zhang
   • Dong Wang

   ORIGINAL ARTICLE 04 February 2021 Pages: 1307 - 1330

   

9. Cooling system during high-pressure microwave curing based on electromagnetic shielding

   • Kai Ju
   • Yong Lu
   • Xiaozhong Hao

   ORIGINAL ARTICLE 04 February 2021 Pages: 1331 - 1345

   

10. Innovative fabrication of diffractive surfaces on plastic parts via textures micromilled on NiP injection moulds

    • Nicola Milan
    • Paolo Parenti
    • Giovanni Lucchetta

    ORIGINAL ARTICLE Open access 04 February 2021 Pages: 1347 - 1359

    

11. Strategy and error analysis for machining the designed microstructured surfaces by structured grinding wheels

    • Amr Monier
    • Bing Guo
    • Wenchao Liu

    ORIGINAL ARTICLE 04 February 2021 Pages: 1361 - 1376

    

12. Influence of polymer contacting rollers on surface texture finish in the belt grinding process

    • Amine Hamdi
    • Sidi Mohammed Merghache
    • Toufik Aliouane

    ORIGINAL ARTICLE 04 February 2021 Pages: 1377 - 1388

    

13. Wear behaviours of PVD-TiN coating onTi-6Al-4V alloy processed by laser powder bed fusion or conventionally processed

    • Hua Li
    • Zhan Wen Chen
    • Maziar Ramezani

    ORIGINAL ARTICLE 04 February 2021 Pages: 1389 - 1399

    

14. Effect of double-excitation ultrasonic elliptical vibration turning trajectory on surface morphology

    • Bingjun Huo
    • Bo Zhao
    • Xiaobo Wang

    ORIGINAL ARTICLE 05 February 2021 Pages: 1401 - 1414

    

15. The effect of thermal frequency and current amplitude on weldability, microstructural evolution and mechanical properties of AA7075 alloy joint in DP-GMAW process

    • Behnam Soltani
    • Amirreza Farnia
    • S. H. Mousavi Anijdan

    ORIGINAL ARTICLE 05 February 2021 Pages: 1415 - 1429

    

16. Experimental evaluation of the minimum uncut chip thickness (MUCT) in AISI H13 steel, using the end milling operation

    • Tatiany Mafra da Silva
    • Anselmo Eduardo Diniz
    • Reginaldo Teixeira Coelho

    ORIGINAL ARTICLE 06 February 2021 Pages: 1431 - 1447

    

17. Correction to: Experimental evaluation of the minimum uncut chip thickness (MUCT) in AISI H13 steel, using the end milling operation

    • Tatiany Mafra da Silva
    • Anselmo Eduardo Diniz
    • Reginaldo Teixeira Coelho

    Correction 22 February 2021 Pages: 1449 - 1449

18. Preliminary geometrical and microstructural characterization of WC-reinforced NiCrBSi matrix composites fabricated by plasma transferred arc additive manufacturing through Taguchi-based experimentation

    • Jose Guadalupe Mercado Rojas
    • Morteza Ghasri-Khouzani
    • Ahmed Jawad Qureshi

    ORIGINAL ARTICLE 06 February 2021 Pages: 1451 - 1468

    

19. A new multiobjective optimization with elliptical constraints approach for nonlinear models implemented in a stainless steel cladding process

    • Eduardo Rivelino Luz
    • Estevão Luiz Romão
    • Pedro Paulo Balestrassi

    ORIGINAL ARTICLE 06 February 2021 Pages: 1469 - 1484

    

20. Data-driven identification and control based on optic tracking feedback for robotic systems

    • Josué Gómez
    • Chidentree Treesatayapun
    • América Morales

    ORIGINAL ARTICLE 07 February 2021 Pages: 1485 - 1503

    

21. Influence of biodegradable lubricant on the ecology, lubrication, and machining process in minimum quantity lubrication

    • Hongjie Pei
    • Fu Li
    • Chungen Shen

    ORIGINAL ARTICLE 08 February 2021 Pages: 1505 - 1516

    

22. The influence of dynamic error outside servo-loop on the trajectory error

    • Dun Lyu
    • Qing Liu
    • Hui Liu

    ORIGINAL ARTICLE 08 February 2021 Pages: 1517 - 1525

    

23. Predicting the material removal rate during electrical discharge diamond grinding using the Gaussian process regression: a comparison with the artificial neural network and response surface methodology

    • Yun Zhang
    • Xiaojie Xu

    ORIGINAL ARTICLE 08 February 2021 Pages: 1527 - 1533

    

24. On the effect of Q_net on compressive residual stresses and ductile toughness of dissimilar HAZ in robotic GMAW joints between A572-50 and A36 steels

    • Benjamín Vargas Arista
    • Isidro Guzman Flores
    • Joaquín del Prado Villasana

    ORIGINAL ARTICLE 08 February 2021 Pages: 1535 - 1546

    

25. Performance improvement of carbide cutting tool for Ti6Al4V alloys using electromagnetic treatment

    • Wenmeng Zhou
    • Jiachen Lin
    • Pingfa Feng

    ORIGINAL ARTICLE 08 February 2021 Pages: 1547 - 1560

    

26. A new hybrid process combining machining and selective laser melting to manufacture an advanced concept of conformal cooling channels for plastic injection molds

    • Felipe Marin
    • Adriano Fagali de Souza
    • Luis Norberto López de Lacalle

    ORIGINAL ARTICLE 08 February 2021 Pages: 1561 - 1576

    

27. Processing behavior and surface quality control of the engine fuel nozzle precision machining by AFM containing magnetic particles

    • Junye Li
    • Jinbao Zhu
    • Chengyu Xu

    ORIGINAL ARTICLE 09 February 2021 Pages: 1577 - 1590

    

28. Experimental and numerical analysis on bulge forming process of GH4738 thick-walled ring

    • Yang Hu
    • Dong Liu
    • Xinglin Zhu

    ORIGINAL ARTICLE 09 February 2021 Pages: 1591 - 1604

    

29. Investigation on magnetic and flow field in magnetorheological jet machining

    • Zhe Lv
    • Rongguo Hou
    • Guoyong Zhao

    ORIGINAL ARTICLE 09 February 2021 Pages: 1605 - 1613

    

30. Optimal calculation and experimental study on cutting force of hypoid gear processed by generating method

    • Chuang Jiang
    • Jing Deng
    • Xiaozhong Deng

    ORIGINAL ARTICLE 09 February 2021 Pages: 1615 - 1635

    

31. Parametric roller path design in multi-pass conventional spinning of curvilinear generatrix parts

    • Leitao Gao
    • Jinlong Song
    • Zhongqi Yu

    ORIGINAL ARTICLE 10 February 2021 Pages: 1637 - 1648

    

32. Research on a new method for optimizing surface roughness of cavitation abrasive flow polishing monocrystalline silicon

    • Jun Zhao
    • Rui Wang
    • Shiming Ji

    ORIGINAL ARTICLE 10 February 2021 Pages: 1649 - 1661

    

33. On the measurement of residual stresses in fibre metal laminates

    • Morteza Abouhamzeh
    • Niall Smyth
    • Jos Sinke

    ORIGINAL ARTICLE 10 February 2021 Pages: 1663 - 1671

    

34. Characterization of vitrified alumina grinding wheel topography using 3D roughness parameters: influence of the crystalline structure of abrasive grains

    • Leire Godino
    • Iñigo Pombo
    • Borja Izquierdo

    ORIGINAL ARTICLE 10 February 2021 Pages: 1673 - 1684

    

35. Development of a novel device for analysis of high-speed cutting processes considering the influence of dynamic factors

    • Ondrej Dvoracek
    • Daniel Lechowicz
    • Stephan Frybort

    ORIGINAL ARTICLE 10 February 2021 Pages: 1685 - 1697

    

36. The influence of cut direction and process parameters in wire electrical discharge machining of carbon fibre–reinforced plastic composites

    • Ramy Abdallah
    • Sein Leung Soo
    • Richard Hood

    ORIGINAL ARTICLE Open access 11 February 2021 Pages: 1699 - 1716

    

37. Mechanism study of the electrical discharge ablation milling with a microcutting depth

    • Yunxiao Han
    • Zhidong Liu
    • Hongpeng Mu

    ORIGINAL ARTICLE 11 February 2021 Pages: 1717 - 1725

    

38. Heat-assisted μ-electrical discharge machining of silicon

    • Noor Dzulaikha Daud
    • Farah Afiqa Mohd Ghazali
    • Mohamed Sultan Mohamed Ali

    ORIGINAL ARTICLE 12 February 2021 Pages: 1727 - 1738

    

39. Study on mechanical properties and microstructural feature of magnetic pulse welding joint between Cu and Al sheets

    • Chenguang Wang
    • Quanxiaoxiao Liu
    • Junjia Cui

    ORIGINAL ARTICLE 12 February 2021 Pages: 1739 - 1751

    

40. Tolerance management during the design of composite structures considering variations in design parameters

    • Michael Franz
    • Benjamin Schleich
    • Sandro Wartzack

    ORIGINAL ARTICLE Open access 13 February 2021 Pages: 1753 - 1770

    

41. Influence of anisotropy of KDP crystal on the surface shape deviation of slice by diamond wire saw

    • Zongqiang Li
    • Peiqi Ge
    • Chengyun Li

    ORIGINAL ARTICLE 13 February 2021 Pages: 1771 - 1785

    

42. The effect of Zn coating layer on the microstructure and mechanical properties of friction stir spot welded galvanized DP590 high-strength steel plates

    • Zeyu Rong
    • Linqing Li
    • Shaokang Guan

    ORIGINAL ARTICLE 15 February 2021 Pages: 1787 - 1798