Microstructural variations and machining characteristics of silicon nitride ceramics from increasing the temperature in laser assisted machining Su-Jin LeeJong-Do KimJeong Suh OriginalPaper 01 August 2014 Pages: 1269 - 1274
Effect of the magnetic pole arrangement on the surface roughness of STS 304 by magnetic abrasive machining Sung YoonJuei-Feng TuSang Don Mun OriginalPaper 01 August 2014 Pages: 1275 - 1281
Influence of human factor in the AACMM performance: a new evaluation methodology González-Madruga DanielBarreiro JoaquínMartínez-Pellitero Susana OriginalPaper 01 August 2014 Pages: 1283 - 1291
Research on the rotational accuracy measurement of an aerostatic spindle in a rolling bearing performance analysis instrument Zhaohui YangJun HongMichael Yu Wang OriginalPaper 01 August 2014 Pages: 1293 - 1302
Roll to roll air-floating oven drying process design and analysis for printed electronics Tae-Gun JeongYong-Ho SeoChang-Wan Kim OriginalPaper 01 August 2014 Pages: 1303 - 1310
A study on integrated design for manufacturing processes of a compressed natural gas composite vessel Jun-Ho BaeHyun-Woo LeeChul Kim OriginalPaper 01 August 2014 Pages: 1311 - 1321
Prediction of residual strength after impact of CFRP composite structures Jae-Mean KooJung-Hun ChoiChang-Sung Seok OriginalPaper 01 August 2014 Pages: 1323 - 1329
Bending fatigue life evaluation of Cu-Mg alloy contact wire Guo ZhenYongseok KimSam-Young Kwon OriginalPaper 01 August 2014 Pages: 1331 - 1335
Mechanism for reducing stress concentrations in bolt-nut connectors Chae-Ho LeeBeom-Jun KimSeog-Young Han OriginalPaper 01 August 2014 Pages: 1337 - 1343
The characteristics of shear adhesive interface fracture of aluminum foam DCB bonded using a single-lap method Ho Sun ChoJae Ung Cho OriginalPaper 01 August 2014 Pages: 1345 - 1350
Dynamic analysis of three-dimensional drivetrain system of wind turbine Wei ShiHyun-Chul ParkChang-Wan Kim OriginalPaper 01 August 2014 Pages: 1351 - 1357
Design of drug-delivery micro-wheel and auto-rolling control by change of gravity center Jing-Yao LaiNan-Chyuan TsaiHsin-Lin Chiu OriginalPaper 01 August 2014 Pages: 1359 - 1369
Optimization process for concept design of tactical missiles by using pareto front and TOPSIS Kwang-Ki LeeKwon-Hee LeeSeung-Ho Han OriginalPaper 01 August 2014 Pages: 1371 - 1376
Thermodynamic behaviors of magnetic-fluid in a thin channel with magnetic field and aspect ratio Sung-Chul KimJae-Hyeong SeoMoo-Yeon Lee OriginalPaper 01 August 2014 Pages: 1377 - 1382
Semi-analytic correlation for predicting permeability of micro-square-pillar array Dong-Pyo HongJunyoung LimChan Byon OriginalPaper 01 August 2014 Pages: 1383 - 1387
Least material optimization of natural-convective heat sinks Dong-Pyo HongDong-Yeon LeeChan Byon OriginalPaper 01 August 2014 Pages: 1389 - 1395
Computational simulation for optimizing the thermal hyperfine patterning process and its experimental verification Hyun-June OhYong-Phil JeonChung-Gil Kang OriginalPaper 01 August 2014 Pages: 1397 - 1404
Numerical investigation on the effects of the positional variation of porosity in thin porous layers Taqi Ahmad CheemaChoon-Young LeeCheol-Woo Park OriginalPaper 01 August 2014 Pages: 1405 - 1410
Ultrasonic manipulation of magnetic particles in a microfluidic channel Ariful Haque SiddiqueSeung Hyun ChoCheolGi Kim OriginalPaper 01 August 2014 Pages: 1411 - 1416
Fabrication of passive micromixer using a digital micromirror device-based maskless lithography system Yong-Kyu ChoTae-Heon HanMyeong-Woo Cho OriginalPaper 01 August 2014 Pages: 1417 - 1422
Development of capacitive-type MEMS microphone with CMOS amplifying chip Young Hwa LeeYoungdo JungShin Hur OriginalPaper 01 August 2014 Pages: 1423 - 1427
Friction coefficient for the quantification of needle grasp in the lifting-thrusting method Young-Nam SonJung KimSeung-Deok Lee OriginalPaper 01 August 2014 Pages: 1429 - 1434
Investigation on the effect of an auxiliary pulsing jet of water at the top side of chip during hard turning of AISI 4340 steel with minimal fluid application R. Robinson GnanaduraiA. S. Varadarajan OriginalPaper 01 August 2014 Pages: 1435 - 1441
A new eco-design approach on CAD systems Raoudha GahaBernard YannouAbdelmajid Benamara OriginalPaper 01 August 2014 Pages: 1443 - 1451
Effect of polypyrrole coating on Li powder anode for lithium-sulfur secondary batteries Soo jung OhWoo young Yoon OriginalPaper 01 August 2014 Pages: 1453 - 1457
Shear cutting theory for the peripheral edges of brush blades, and tests of its effectiveness Young-Doo KwonSang-Jun ParkHyun-Wook Kwon OriginalPaper 01 August 2014 Pages: 1459 - 1465
Design of bridgeless IPMSM to reduce mass of applied permanent magnets Jin-Young ParkJae-Wook LeeHyun-Deok Kim OriginalPaper 01 August 2014 Pages: 1467 - 1472
Mg scroll forging with AZ80 under warm forming condition Sang-Ik LeeJonghun YoonJunghwan Lee OriginalPaper 01 August 2014 Pages: 1473 - 1477
A study on HVOF coating of WC-metal powder on super alloy In718 of magnetic bearing shaft material of turbo-blower Tong Yul ChoHui Gon ChunJae Hong Yoon OriginalPaper 01 August 2014 Pages: 1479 - 1484
Mechanical behavior of microscale carbon pillar fabricated by focused ion beam induced deposition Chung-Soo KimSung-Hoon Ahn OriginalPaper 01 August 2014 Pages: 1485 - 1488
Enabling of local value creation via openness for emergent synthesis Steffen HeyerNariaki NishinoGünther Seliger OriginalPaper 01 August 2014 Pages: 1489 - 1493