A study on deburring of magnesium alloy plate by magnetic abrasive polishing Tae-Wan KimJae-Seob Kwak OriginalPaper 21 May 2010 Pages: 189 - 194
A study on the machining of compressor rotors using formed tools Sang-Yoon ParkLee Hi-KoanMun Sang-Don OriginalPaper 21 May 2010 Pages: 195 - 200
Generation of velocity profiles with speed limit of each axis for high-speed machining using look-ahead buffer Cheol-Soo Lee OriginalPaper 21 May 2010 Pages: 201 - 208
Sensitivity control of a MR-damper semi-active suspension Arjon TurnipSeonghun ParkKeum-Shik Hong OriginalPaper 21 May 2010 Pages: 209 - 218
Torque sensor calibration using virtual load for a manipulator Sang-Hyuk LeeYoung-Loul KimJae-Bok Song OriginalPaper 21 May 2010 Pages: 219 - 225
A robust control of electro hydrostatic actuator using the adaptive back-stepping scheme and fuzzy neural networks Han Me KimSung Hwan ParkJong Shik Kim OriginalPaper 21 May 2010 Pages: 227 - 236
Fault detection of cycle-based signals using wavelet transform in FAB processes Jun Seok KimJae Hyun LeeSung-Shick Kim OriginalPaper 21 May 2010 Pages: 237 - 246
Edge identification of a small object through a low-resolution tactile sensor array Tri Cong PhungYong Seok IhnHyouk Ryeol Choi OriginalPaper 21 May 2010 Pages: 247 - 254
Enhanced SLAM for a mobile robot using extended Kalman Filter and neural networks Kyung-Sik ChoiSuk-Gyu Lee OriginalPaper 21 May 2010 Pages: 255 - 264
Development and application of VPG simulation technique based on equivalent virtual road profile Dae-Oh KangKihong ParkJay Il Jeong OriginalPaper 21 May 2010 Pages: 265 - 272
Rapid surface reconstruction from a point cloud using the least-squares projection Dong-Jin Yoo OriginalPaper 21 May 2010 Pages: 273 - 283
Simulations of the vibration response of mannequins in car seats by changing parameter and excitation Seong Keol Kim OriginalPaper 21 May 2010 Pages: 285 - 289
A new approach for molding multi component parts Hong-Seok ParkDinh Ba Hung Anh OriginalPaper 21 May 2010 Pages: 291 - 297
Development of an apparatus for removing magnetic sludge by permanent magnets setup in the condenser of the power plant Jun-Ho BaeMoon-Saeng KimChul Kim OriginalPaper 21 May 2010 Pages: 299 - 307
Fracture toughness of CFRP laminated plates according to resin content In Young YangJoo Yeong JeongJi Hoon Kim OriginalPaper 21 May 2010 Pages: 309 - 313
Assessment of running safety of railway vehicles using multibody dynamics Beom-Gyu EomHi Sung Lee OriginalPaper 21 May 2010 Pages: 315 - 320
Preparation and absorption properties of ZnO nanostructures for cleanup of H2S contained gas No-Kuk ParkGi Bo HanTae Jin Lee OriginalPaper 21 May 2010 Pages: 321 - 325
NC machining of free-form Kriging surfaces Abbas Vafaeesefat OriginalPaper 21 May 2010 Pages: 327 - 333
Three-dimensional microstructure using partitioned cross-sections in projection microstereolithography Young-Myoung HaIn-Baek ParkSeok-Hee Le OriginalPaper 21 May 2010 Pages: 335 - 340
Tool wear, chip formation and workpiece surface issues in CBN hard turning: A review Manu DograVishal S. SharmaJasminder Singh Dureja ReviewPaper 21 May 2010 Pages: 341 - 358