Strontium in Al–Si–Mg Alloy: A Review M. R. Sai GaneshNikhil ReghunathKarthik V. Shankar ReviewPaper 05 October 2021 Pages: 1 - 40
Nanostructured Materials and Nanocomposites by Mechanical Alloying: An Overview C. SuryanarayanaAhmed A. Al-JouboriZhi Wang ReviewPaper 21 August 2021 Pages: 41 - 53
Assessment of Process, Parameters, Residual Stress Mitigation, Post Treatments and Finite Element Analysis Simulations of Wire Arc Additive Manufacturing Technique M. D. Barath KumarM. Manikandan ReviewPaper 24 August 2021 Pages: 54 - 111
Analysing the Fatigue Behaviour and Residual Stress Relaxation of Gradient Nano-Structured 316L Steel Subjected to the Shot Peening via Deep Learning Approach Erfan MalekiOkan UnalSara Bagherifard OriginalPaper Open access 29 July 2021 Pages: 112 - 131
Uniaxial Compression Properties and Compression Fatigue Performance of Selective Laser Melted Ti–6Al–4V Cellular Structure Ming-Wei WuJhewn-Kuang ChenAnnadurai Dhinakar OriginalPaper 28 July 2021 Pages: 132 - 144
Influence of Nanoparticles Reinforcements on Aluminium 6061 Alloys Fabricated via Novel Ultrasonic Aided Rheo-Squeeze Casting Method T. ArunkumarVelmurugan PavananKarthikeyan Ramachandran OriginalPaper Open access 29 May 2021 Pages: 145 - 154
Investigation of the Microstructure and Mechanical Characteristics of Lattice Structures Produced by Laser Powder Bed Fusion Method A. Tamer ErturkM. Enes BuldukEser Yarar OriginalPaper 10 September 2021 Pages: 155 - 167
Tensile Properties of Additively Manufactured C-18150 Copper Alloys Congyuan ZengHao WenShengmin Guo OriginalPaper 17 September 2021 Pages: 168 - 180
Laser Surface Texturing in Powder Bed Fusion: Numerical Simulation and Experimental Characterization Vijay MandalShashank SharmaJ. Ramkumar OriginalPaper 29 September 2021 Pages: 181 - 196
Effects of Laser Power on the Microstructure Evolution and Mechanical Properties of Ti–6Al–4V Alloy Manufactured by Direct Energy Deposition Yukyeong LeeEun Seong KimJung Gi Kim OriginalPaper 01 October 2021 Pages: 197 - 204
Effect of Annealing and Crack Orientation on Fatigue Crack Propagation of Ti64 Alloy Fabricated by Direct Energy Deposition Process Soyoung KimHojun OhSangshik Kim OriginalPaper 04 October 2021 Pages: 205 - 215
Microstructure and Properties of 2Cr13-xMo Stainless Steels Fabricated by Direct Laser Deposition Jing LiangZiyang LinKun Tian OriginalPaper 09 September 2021 Pages: 216 - 226
Equiatomic, Cu‐Containing CrCuFeTiV 3d Transition Metal High Entropy Alloy with an Enhanced Strength and Hardness Synergy Jiaojiao YiLin YangLisha Liu OriginalPaper 17 July 2021 Pages: 227 - 236
Microtextural Characterization of Additively Manufactured SS316L After Hot Isostatic Pressing Heat Treatment Kanwal ChadhaYuan TianClodualdo Aranas OriginalPaper 14 September 2021 Pages: 237 - 249
Study of the Effect of Two Separate Tilt Angles of Laser Scanning Lines on the Microstructure and Mechanical Properties in Direct Metal Laser Sintered AlSi10Mg Alloy Aniket ChakrabartyVivek Kumar SahuNiloy Khutia OriginalPaper 09 October 2021 Pages: 250 - 268
pyMPEALab Toolkit for Accelerating Phase Design in Multi-principal Element Alloys Upadesh SubediAnil KunwarKhem Gyanwali OriginalPaper Open access 16 November 2021 Pages: 269 - 281
Multiphysics Modeling of Thermal Behavior of Commercial Pure Titanium Powder During Selective Laser Melting Wenlin YeJin BaoYing Zhang OriginalPaper 31 August 2021 Pages: 282 - 296
Selective Laser Melting Process for Sensor Embedding into SUS316L with Heat Dissipative Inner Cavity Design Min Sik LeeHayeol KimIm Doo Jung OriginalPaper 05 October 2021 Pages: 297 - 305
Correction to: Selective Laser Melting Process for Sensor Embedding into SUS316L with Heat Dissipative Inner Cavity Design Min Sik LeeHayeol KimIm Doo Jung Correction 08 December 2021 Pages: 306 - 306
Fabrication of Gas Metal Arc Welding Based Wire Plus Arc Additive Manufactured 347 Stainless Steel Structure: Behavioral Analysis Through Experimentation and Finite Element Method R. PramodS. Mohan KumarReza Tangestani OriginalPaper 28 August 2021 Pages: 307 - 321
Utilizing Additive Friction Stir Processing to Fabricate B4C Reinforced Ti–6Al–4V Matrix Surface Composite: Microstructure Refinement and Enhancement in Mechanical Properties H. A. DeoreJ. MishraV. D. Hiwarkar OriginalPaper 11 November 2021 Pages: 322 - 335
Correction to: Effects of I- and W-Phases Under Identical Conditions on Microstructure and Mechanical Properties of As-Cast Mg–Zn–Y Alloys at Room and Elevated Temperatures Young-Gil JungWonseok YangDo Hyang Kim Correction 09 December 2021 Pages: 336 - 336