1. Stability of Y-Ti-O nanoparticles during laser deposition of oxide dispersion strengthened steel powder

   • Kwangjun Euh
   • Barton Arkhurst
   • Jeoung Han Kim

   Research Paper 04 September 2017 Pages: 1063 - 1074

2. Crystal plasticity finite element simulation of NiTi shape memory alloy based on representative volume element

   • Li Hu
   • Shuyong Jiang
   • Dong Sun

   Research Paper 14 November 2017 Pages: 1075 - 1086

3. Aging precipitation behavior and its influence on mechanical properties of Mn18Cr18N austenitic stainless steel

   • Fengming Qin
   • Yajie Li
   • Huiqin Chen

   Research Paper 14 November 2017 Pages: 1087 - 1096

4. Wear behaviors of pure aluminum and extruded aluminum alloy (AA2024-T4) under variable vertical loads and linear speeds

   • Jeki Jung
   • Jeong-Jung Oak
   • Yong Ho Park

   Research Paper 14 November 2017 Pages: 1097 - 1105

5. Irradiation-induced hardening and softening of CLAM steel under Fe ion irradiation

   • Qingshan Li
   • Yinzhong Shen
   • Jun Zhu

   Research Paper 14 November 2017 Pages: 1106 - 1111

6. Influence of processing parameters on the characteristics of surface layers of low temperature plasma nitrocarburized AISI 630 martensitic stainless steel

   • Insup Lee

   Research Paper 14 November 2017 Pages: 1112 - 1120

7. Heat treated twin wire arc spray AISI 420 coatings under dry and wet abrasive wear

   • E. Rodriguez
   • M. A. González
   • J. Ibarra

   Research Paper 14 November 2017 Pages: 1121 - 1132

8. Comparison of structural and optical properties of TeO₂ nanostructures synthesized using various substrate conditions

   • Taek-Kyun Jung
   • Min Ryou
   • Changhyun Jin

   Research Paper 18 October 2017 Pages: 1133 - 1138

9. Sintering properties of Ti-6Al-4V-xMo powder prepared by addition of Mo to Ti-6Al-4V scraps and subsequent pulverization

   • Jung-Min Oh
   • Ki-Min Roh
   • Jae-Won Lim

   Research Paper 18 October 2017 Pages: 1139 - 1143

10. Enhanced thermal diffusivity of copperbased composites using copper-RGO sheets

    • Sangwoo Kim
    • Hyouk-Chon Kwon
    • Hyo-Soo Lee

    Research Paper 14 November 2017 Pages: 1144 - 1149

11. In situ synthesis and strengthening of powder metallurgy high speed steel in addition of LaB₆

    • Weijun Shen
    • Linping Yu
    • Nan Lin

    Research Paper 14 November 2017 Pages: 1150 - 1157

12. Microstructure and mechanical properties of friction stir lap welded Mg/Al joint assisted by stationary shoulder

    • Shude Ji
    • Zhengwei Li

    Research Paper 14 November 2017 Pages: 1158 - 1167

13. Microstructures and mechanical properties of bonding layers between low carbon steel and alloy 625 processed by gas tungsten arc welding

    • Shuai Lou
    • Seul Bi Lee
    • Yoon Suk Choi

    Research Paper 14 November 2017 Pages: 1168 - 1175

14. Effects of drawing strain and post-annealing conditions on microstructural evolution and tensile properties of medium- and high-carbon steels

    • Sung Hyuk Park
    • Taekyung Lee
    • Chong Soo Lee

    Research Paper 14 November 2017 Pages: 1176 - 1187

15. SHS synthesis of Si-SiC composite powders using Mg and reactants from industrial waste

    • Tawat Chanadee

    Research Paper 14 November 2017 Pages: 1188 - 1196

16. Characteristics of copper-clad aluminum rods prepared by horizontal continuous casting

    • Yubo Zhang
    • Ying Fu
    • Tongmin Wang

    Research Paper 14 November 2017 Pages: 1197 - 1203

17. Effects of substrate preheating during direct energy deposition on microstructure, hardness, tensile strength, and notch toughness

    • Gyeong Yun Baek
    • Ki Yong Lee
    • Do Sik Shim

    Research Paper 18 October 2017 Pages: 1204 - 1215

18. Formation of crystalline phase in the glass matrix of Zr-Co-Al glass-matrix composites and its effect on their mechanical properties

    • Woo Chul Kim
    • Kang Chul Kim
    • Do Hyang Kim

    Research Paper 14 November 2017 Pages: 1216 - 1222

19. Final thickness reduction and development of Goss texture in C- and Al-free Fe-3%Si-0.1%Mn-0.012%S electrical steel

    • Eun Jee Oh
    • Nam Hoe Heo
    • Yang Mo Koo

    Research Paper 18 October 2017 Pages: 1223 - 1226

20. Catalysts characteristics of Ni/YSZ core-shell according to plating conditions using electroless plating

    • Hyun-Wook Park
    • Jae-Won Jang
    • Mi-Jai Lee

    Research Paper 14 November 2017 Pages: 1227 - 1233

21. Effects of Ni particle morphology on cell performance of Na/NiCl₂ battery

    • Mangi Kim
    • Cheol-Woo Ahn
    • Joon-Hwan Choi

    Research Paper 14 November 2017 Pages: 1234 - 1240

22. High performance Sb₂S₃/carbon composite with tailored artificial interface as an anode material for sodium ion batteries

    • Jeong-Hee Choi
    • Chung-Wan Ha
    • Sang-Min Lee

    Research Paper 14 November 2017 Pages: 1241 - 1249

23. Effects of La₂O₃ content and particle size on the long-term stability and thermal cycling property of La₂O₃-dispersed SUS430 alloys for SOFC interconnect materials

    • Jung-Won Lee
    • Muhammad Taqi Mehran
    • Joon-Hyung Shim

    Research Paper 14 November 2017 Pages: 1250 - 1256

24. Hardness of AISI type 410 martensitic steels after high temperature irradiation via nanoindentation

    • Owais Ahmed Waseem
    • Jong-Ryul Jeong
    • Ho Jin Ryu

    Research Paper 14 November 2017 Pages: 1257 - 1265