1. Numerical investigation of the effect of primary nozzle geometries on flow structure and ejector performance for optimal design

   • Anna Li
   • Jianan Chen
   • Zhu Huang

   Original Article 11 May 2023 Pages: 2139 - 2148

2. Energy and exergy analysis of gas turbine combined cycle with exhaust gas recirculation under part-load conditions

   • Keying Li
   • Jinling Chi
   • Shijie Zhang

   Original Article 11 May 2023 Pages: 2149 - 2160

3. Optimization of impedance boundary-controlled casing treatment on subsonic compressors

   • Dakun Sun
   • Yuqing Wang
   • Xiaofeng Sun

   Original Article 11 May 2023 Pages: 2161 - 2169

4. Impact of surface roughness on gas turbine engine fan and compressor rotor

   • Ashima Malhotra
   • Shraman Goswami
   • A. M. Pradeep

   Original Article 02 May 2023 Pages: 2171 - 2177

5. Influence of an upstream transonic axial compressor stage on the performance of inter-stage duct

   • Lakshya Kumar
   • Dilipkumar B. Alone
   • A. M. Pradeep

   Original Article 06 May 2023 Pages: 2179 - 2185

6. Studies on V-shaped flow control devices to improve film cooling effectiveness for air-cooled turbines

   • Ken-ichi Funazaki
   • Nao Yoshida
   • Suzuna Saito

   Original Article 06 May 2023 Pages: 2187 - 2197

7. Effects of pin-fins with trapezoidal endwall on heat transfer characteristics in gas turbine blade internal cooling channels

   • Cong-Truong Dinh
   • Khanh-Duy Cong Do
   • Hoanh-Son Truong

   Original Article 03 May 2023 Pages: 2199 - 2210

8. Investigation of axial spacing effect on noise radiation generated by rotor-stator interaction

   • Wangjian Shu
   • Lin Du
   • Xiaofeng Sun

   Original Article 02 May 2023 Pages: 2211 - 2221

9. Effect of axial extension on parameterized endwall contour with incidence change for low-pressure turbine linear cascade

   • Anand P. Darji
   • Beena D. Baloni
   • Chetan S. Mistry

   Original Article 02 May 2023 Pages: 2223 - 2232

10. A numerical study on new venturi mixer design with ring-type damper to control fuel opening

    • Young Bae Kim
    • Dong Kyu Seo
    • Young Sik Jeong

    Original Article 02 May 2023 Pages: 2233 - 2240

11. Application of hierarchical symbolic fuzzy entropy and sparse Bayesian ELM to bearing fault diagnosis

    • Liying Yuan
    • Hongqi Wang

    Original Article 03 May 2023 Pages: 2241 - 2252

12. Study on reduction of squeal noise of disc brake system considering braking temperature of urban railway vehicle

    • Seoyeon Ahn
    • Changhyun Sohn
    • Chanhyuk Nam

    Original Article 03 May 2023 Pages: 2253 - 2262

13. Dynamic balancing of multispeed multidisk rotor

    • Yulin Guo
    • Jianfei Yao
    • Yan Li

    Original Article 03 May 2023 Pages: 2263 - 2274

14. Vibration response of an elastic disc excited by a piezoelectric disc

    • Byeong Ho An
    • Jin Oh Kim

    Original Article 02 May 2023 Pages: 2275 - 2288

15. Fault identification of a chain conveyor based on functional data feature engineering and optimized multi-layer kernel extreme learning machine

    • Hao Wen
    • Baolin Hou
    • Xin Jin

    Original Article 02 May 2023 Pages: 2289 - 2300

16. Experimental evaluation models of vehicle ride quality for two vibration types: primary ride and secondary ride

    • Hansol Park
    • Yeon June Kang
    • Kwangduk Baek

    Original Article 02 May 2023 Pages: 2301 - 2309

17. Vibration of three-phase hybrid viscoelastic nanocomposites beams

    • Farzad Ebrahimi
    • Reza Nopour
    • Nguyen Dinh Duc

    Original Article 02 May 2023 Pages: 2311 - 2317

18. Effect of machining parameters on surface quality and delamination of carbon/glass/epoxy hybrid composite material during end milling operation

    • Qaiser Saghir
    • Atta ur Rehman Shah
    • Jung-il Song

    Original Article 02 May 2023 Pages: 2319 - 2324

19. An innovative sensing method for seam tracking based on the arc ‘jump sidewall’ behavior

    • Wenji Liu
    • Yafeng Zhang
    • Jianfeng Yue

    Original Article 02 May 2023 Pages: 2325 - 2332

20. An improved critical plane-energy multiaxial fatigue life prediction model considering shear mean stress

    • Jie Zhou
    • Zhengchao Tan
    • Yuexing Wang

    Original Article 02 May 2023 Pages: 2333 - 2341

21. A study of the impact of high-speed sealing parameter gradients on the seal strength in a multilayer polypropylene film

    • Jorge E. Uribe-Juárez
    • Ma. Pilar Corona-Lira
    • Alejandro C. Ramírez-Reivich

    Original Article 02 May 2023 Pages: 2343 - 2352

22. Fatigue residual useful life estimation of Ni-base alloy weld with time-series data

    • Jae Phil Park
    • Junhyuk Ham
    • Chi Bum Bahn

    Original Article 02 May 2023 Pages: 2353 - 2362

23. Taguchi based optimization to improve mechanical properties of high carbon rail steels via bainitic microstructure

    • Abdulkadir Kilic
    • Yasin Sarikavak

    Original Article 02 May 2023 Pages: 2363 - 2373

24. NACA four-digit airfoil series optimization: a comparison between genetic algorithm and sequential quadratic programming

    • Durmuş Sinan Körpe
    • Ibrahim Halil Güzelbey

    Original Article 02 May 2023 Pages: 2375 - 2382

25. Oil film deposition characteristics and judgment of lubrication effect of splash lubricated gears

    • Fengxia Lu
    • Kun Wei
    • Heyun Bao

    Original Article 03 May 2023 Pages: 2383 - 2393

26. Effect of in-phase type waviness in the walls of a confined Savonius rotor placed in a long channel

    • J. Ramarajan
    • S. Jayavel

    Original Article 03 May 2023 Pages: 2395 - 2403

27. Enhanced performance of oscillating wing energy harvester using active controlled flap

    • Maqusud Alam
    • C. H. Sohn

    Original Article 02 May 2023 Pages: 2405 - 2415

28. A semi-implicit finite element formulation of the partitioned method for fluid-structure interaction based on a flux boundary condition of pressure equation

    • Sang Truong Ha
    • Hyoung Gwon Choi
    • Sang-Wook Lee

    Original Article 03 May 2023 Pages: 2417 - 2424

29. Aerodynamic performance of high-lift blades in low-pressure turbines with periodic upstream wakes

    • Siyu Yang
    • Baopeng Xu
    • Bin Wang

    Original Article 02 May 2023 Pages: 2425 - 2437

30. Comparison of effects of four subgrid-scale turbulence models in large eddy simulation of a large wind farm

    • Vahid Mazidi Sharafabadi
    • Mani Fathali

    Original Article 02 May 2023 Pages: 2439 - 2449

31. Experimental research on the collapse dynamics of the cavitation bubble near two spherical particles

    • Xiaoxiao Zheng
    • Xiaoyu Wang
    • Yuning Zhang

    Original Article 02 May 2023 Pages: 2451 - 2460

32. Novel anti-loosening nut designed to have large and stable loosening resistance torque

    • Evgeniia Shchelkanova
    • Xi Liu
    • Nao-Aki Noda

    Original Article 02 May 2023 Pages: 2461 - 2469

33. Influence of an initial imperfection on hygro-thermo-mechanical behaviors of FG plates laid on elastic foundation

    • Ismahene Belkorissat
    • Mohammed Ameur

    Original Article 02 May 2023 Pages: 2471 - 2477

34. Calculation method of residual fatigue life of in-service unbonded flexible pipe

    • Qinglong Lei
    • Xiaohua Zhu
    • Heng Luo

    Original Article 02 May 2023 Pages: 2479 - 2490

35. Finite element based bending analysis of rectangular FGM plates using first-order shear deformation theory

    • Ahmad Mamandi

    Original Article 11 May 2023 Pages: 2491 - 2506

36. Contact characteristics and interfacial motion states during sphere oblique impact with initial spin

    • Qingpeng Wang
    • Kai Zhang
    • Guangyin Xu

    Original Article 02 May 2023 Pages: 2507 - 2518

37. A nonlinear friction-cohesive model for characterizing mode II fracture of laminated composites

    • Ruoyu Li
    • Chaocan Cai
    • Xiaodong He

    Original Article 02 May 2023 Pages: 2519 - 2526

38. Design and vibration parameter test of low-frequency axial vibration drilling tool handle

    • Ting Chen
    • Jianming Zheng
    • Chao Cao

    Original Article 03 May 2023 Pages: 2527 - 2535

39. Head behavior on left-turn across path and opposite direction crash using simulation

    • Moon Young Kim
    • Yun Sik Shin
    • Jayil Jeong

    Original Article 02 May 2023 Pages: 2537 - 2543

40. Running-in performance of 7075 aluminum alloy strengthened by burnishing technology

    • Cong Ding
    • Shiqing Feng
    • Zhongyu Piao

    Original Article 02 May 2023 Pages: 2545 - 2553

41. Singularity analysis and workspace optimization of a novel symmetrical 4-limb 5-DOF hybrid robot

    • Xin Tian
    • Tieshi Zhao
    • Erwei Li

    Original Article 02 May 2023 Pages: 2555 - 2567

42. Improved sliding mode control for mobile manipulators based on an adaptive neural network

    • Zhengnan Li
    • Lidong Ma
    • Yufeng Yin

    Original Article 02 May 2023 Pages: 2569 - 2580

43. Design and modeling of a cable-driven articulated robot intended to conduct lower limb recovery training

    • Dongxing Cao
    • Xiangxu Qu
    • Chunlei Wang

    Original Article 02 May 2023 Pages: 2581 - 2592

44. Numerical study on a vehicle driver’s thermal comfort when using water thermal seats during summer and winter

    • Minjung Lee
    • Veerakumar Chinnasamy
    • Honghyun Cho

    Original Article 03 May 2023 Pages: 2593 - 2606

45. Analysis and design of centrifugal compressor for 10 MWe supercritical CO₂ Brayton cycles

    • Javad Hosseinpour
    • Mekuannint Messele
    • Abraham Engeda

    Original Article 04 May 2023 Pages: 2607 - 2621

46. Thermo-hydraulic performance prediction for offset-strip fin heat exchangers using artificial neural networks

    • Sangmin Kim
    • Young Min Seo
    • Man Yeong Ha

    Original Article 03 May 2023 Pages: 2623 - 2638

47. Research on a new method to optimize the thermal characteristics of an engine nacelle cooling module

    • Lei Guo
    • Maojun Zhou
    • Jing Hu

    Original Article 03 May 2023 Pages: 2639 - 2648

48. Numerical analysis with experimental validation for thermal performance of flat plate solar water heater using CuO/distilled water nanofluid in closed loop

    • Helal Ahmad Farhan
    • Sukanta Nayak
    • Manikant Paswan

    Original Article 04 May 2023 Pages: 2649 - 2656

49. High temperature synthesis of TiO₂ nanoparticles as a photochemical catalyst for hydrogen generation using premixed flame burner

    • Ho-Yeon Lee
    • Sang-Soon Hwang

    Original Article 23 February 2023 Pages: 2657 - 2665

50. Research on reliability of centrifugal compressor unit based on dynamic Bayesian network of fault tree mapping

    • Gao Yuan
    • Zhang Liang
    • Yan Zhongchao

    Original Article 03 May 2023 Pages: 2667 - 2677