Stability analysis of real-time hybrid simulation in consideration of time delays of actuator and shake table using delay differential equations Mostafa NasiriAli Safi OriginalPaper 15 April 2019 Pages: 1489 - 1499
Dynamic behavior analysis of push-the-bit rotary steerable bottom hole assembly Zhi-chuan GuanHeng WangGuang-qiang Cao OriginalPaper 15 April 2019 Pages: 1501 - 1511
Early fault detection method for rolling bearing based on multiscale morphological filtering of information-entropy threshold Lingli CuiJialong WangJianfeng Ma OriginalPaper 15 April 2019 Pages: 1513 - 1522
A method for solving causality conflicts in vehicle powertrain modeling Namwook KimWoong LeeDeokjin Kim OriginalPaper 15 April 2019 Pages: 1523 - 1533
A novel rolling-element bearing faults classification method combines lower-order moment spectra and support vector machine Qinyu JiangFaliang Chang OriginalPaper 15 April 2019 Pages: 1535 - 1543
Effect of anodized coating on friction noise in aluminum Jaehyeon NamJaeyoung Kang OriginalPaper 15 April 2019 Pages: 1545 - 1554
Influence of magnetorheological elastomer on tool vibration and cutting performance during boring of hardened AISI4340 steel G. LawranceP. Sam PaulE. Daniel OriginalPaper 15 April 2019 Pages: 1555 - 1561
Optimal control of vibration by multiple tuned liquid dampers using Taguchi method Nguyen Van KhangDo The DuongVu Duc Phuc OriginalPaper 15 April 2019 Pages: 1563 - 1572
Short-term annoyance reduction evoked by active noise control method on turboprop regional aircraft cabin noise Kiseop YoonDongwook KimSoogab Lee OriginalPaper 15 April 2019 Pages: 1573 - 1584
Combination algorithm for cracked rotor fault diagnosis based on NOFRFs and HHR Yang LiuYulai ZhaoHongliang Yao OriginalPaper 15 April 2019 Pages: 1585 - 1593
Dynamic analysis of multilayer ceramic capacitor for vibration reduction of printed circuit board Dongjoon KimWheejae KimWan-Chin Kim OriginalPaper 15 April 2019 Pages: 1595 - 1601
Compilation of load spectrum of machining center spindle and application in fatigue life prediction Guofa LiShengxu WangChuanyang Zhou OriginalPaper 15 April 2019 Pages: 1603 - 1613
Optimization of pulsed current in resistance spot welding of Zn-coated hot-stamped boron steels Joo Yong CheonVijeesh VijayanChangwook Ji OriginalPaper 15 April 2019 Pages: 1615 - 1621
Stress around the hole of single lapped and single bolted joint plates with fitting clearance Wenguang LiuWeiyan Lin OriginalPaper 15 April 2019 Pages: 1623 - 1632
An automatic abrupt signal extraction method for fault diagnosis of aero-engines Qiang PanYing LiuTian He OriginalPaper 15 April 2019 Pages: 1633 - 1640
Grid-independent large-eddy simulation of turbulent wake flow using explicit differential filters Myeongseok KangDonghyun YouSatbir Singh OriginalPaper 15 April 2019 Pages: 1641 - 1649
Numerical investigation of two-phase flow characteristics in multiphase pump with split vane impellers Yi ShiHongwu ZhuJiate Zhang OriginalPaper 15 April 2019 Pages: 1651 - 1661
Comparison of wind turbine power curves using cup anemometer and pulsed doppler light detection and ranging systems Dongheon ShinKyungnam KoHyunsik Kim OriginalPaper 15 April 2019 Pages: 1663 - 1671
Numerical study of droplet vaporization under acoustic pulsing conditions Seongwook ChoGihun Son OriginalPaper 15 April 2019 Pages: 1673 - 1680
Development of custom-made RF coil for magnetic resonance velocimeter with a high spatial resolution Byungkuen YangJee-Hyun ChoSimon Song OriginalPaper 15 April 2019 Pages: 1681 - 1688
Loosening mechanism of threaded fastener for complex structures Keon-Hee BaekNak-Tak JeongMyung-Won Suh OriginalPaper 15 April 2019 Pages: 1689 - 1702
Stiffness of bi-modulus hexagonal and diamond honeycombs Hamed Hatami-MarbiniMilad Rohanifar OriginalPaper 15 April 2019 Pages: 1703 - 1709
The thermo-mechanical behavior of brake discs for high-speed railway vehicles Heerok HongMinsoo KimJunghwan Lee OriginalPaper 15 April 2019 Pages: 1711 - 1721
Post-buckling behavior of carbon fiber epoxy composite plates Serkan ErdemMete Onur KamanMustafa Gur OriginalPaper 15 April 2019 Pages: 1723 - 1730
Numerical study of rectangular spectral collocation method on flow over a circular cylinder B. SmithR. LaoulacheJ. Lee OriginalPaper 15 April 2019 Pages: 1731 - 1741
A method for representation and analysis of conformal cooling channels in molds made of functionally graded tool steel/Cu materials Ki-Hoon Shin OriginalPaper 15 April 2019 Pages: 1743 - 1750
Reliability based design optimization using response surface augmented moment method Sanghoon Lee OriginalPaper 15 April 2019 Pages: 1751 - 1759
Buckling analysis of FGM plates under uniform, linear and non-linear in-plane loading S. J. SinghS. P. Harsha OriginalPaper 15 April 2019 Pages: 1761 - 1767
Analysis of thermoelastic damping in bilayered rectangular microplate resonators with three-dimensional heat conduction Linlin WangXiaopeng LiJinchi Xu OriginalPaper 15 April 2019 Pages: 1769 - 1784
Development and testing of nano particulate lubricant for worm gear application N. SaravanakumarM. L. Jothi SaravananR. Karthikeyan OriginalPaper 15 April 2019 Pages: 1785 - 1791
Critical AC frequency for stable operation of electrowetting-driven optofluidic devices with polymeric electrolyte solutions Jaebum ParkJonghyun HaHo-Young Kim OriginalPaper 15 April 2019 Pages: 1793 - 1797
Feasibility analysis of using a two-stage nutation drive as joint reducer for industrial robots Yongwu CaiLigang YaoJinlong Hong OriginalPaper 15 April 2019 Pages: 1799 - 1807
Effects of high frequency vibratory finishing of aerospace components B. J. WongK. MajumdarS. H. Yeo OriginalPaper 15 April 2019 Pages: 1809 - 1815
Laser beam machining of zirconia ceramic: An investigation of micro-machining geometry and surface roughness Basem M. A. AbdoNaveed AhmedEmad Abouel Nasr OriginalPaper 15 April 2019 Pages: 1817 - 1831
Design of rotatable direct energy deposition optical system Byungjoo ChoiGwangjae LeeYongho Jeon OriginalPaper 15 April 2019 Pages: 1833 - 1839
Bioreactor mimicking knee-joint movement for the regeneration of tissue-engineered cartilage Hun-Jin JeongSo-Jung GwakSeung-Jae Lee OriginalPaper 15 April 2019 Pages: 1841 - 1850
Influence of geometric variables on the structural characteristics of brazed cross-corrugated sinusoidal plate with secondary corrugation Ho Seung JeongJong Rae ChoSang Hu Park OriginalPaper 15 April 2019 Pages: 1851 - 1859
Compliance error calibration for robot based on statistical properties of single joint Liang DuTie ZhangXiaoliang Dai OriginalPaper 15 April 2019 Pages: 1861 - 1868
Teat detection algorithm: YOLO vs. Haar-cascade Akanksha RastogiBeom Sahng Ryuh OriginalPaper 15 April 2019 Pages: 1869 - 1874
Research on flexible dynamics of a 6-DOF industrial robot and residual vibration control with a pre-adaptive input shaper Tie ZhangKangyu LinAimin Zhang OriginalPaper 15 April 2019 Pages: 1875 - 1889
Development of tunable filters using self-folding technology Paul ChastainMinchul Shin OriginalPaper 15 April 2019 Pages: 1891 - 1896
Using inlet guide vane to improve load following ability of solid oxide fuel cell and gas turbine hybrid cycle M. BoroumandA. M. Tousi OriginalPaper 15 April 2019 Pages: 1897 - 1905
Thermal characteristics of an ammonia-charged closed-loop pulsating heat pipe Md Shahidul HaqueAntara MajumdarMd. Mahbubur Razzaq OriginalPaper 15 April 2019 Pages: 1907 - 1914
A study on thermal fluid flow of magnetron cooling for microwave oven Dong Ho ParkEung Ryeol SeoChang Seon Lee OriginalPaper 15 April 2019 Pages: 1915 - 1923
Mesoscopic investigation of frost crystal nucleation on cold surface based on the lattice-Boltzmann method Jianying GongJianqiang HouTieyu Gao OriginalPaper 15 April 2019 Pages: 1925 - 1935
Investigation of combustion and emission characteristics of n-hexane and n-hexadecane additives in diesel fuel Cihan BayindirliMehmet Celik OriginalPaper 15 April 2019 Pages: 1937 - 1946
Effect of swirl and number of swirler vanes on combustion characteristics of methane inverse diffusion flame Vipul PatelRupesh Shah OriginalPaper 15 April 2019 Pages: 1947 - 1958
Multiple model-based detection and estimation scheme for gas turbine sensor and gas path fault simultaneous diagnosis Qingcai YangShuying LiYunpeng Cao OriginalPaper 15 April 2019 Pages: 1959 - 1972
Effect of devolatilization model on flame structure of pulverized coal combustion in a jet-burner system Seongyool AhnHiroaki WatanabeToshiaki Kitagawa OriginalPaper 15 April 2019 Pages: 1973 - 1979
Temperature dependency of the fill factor in PV modules between 6 and 40 °C Hongwei QuXingcan Li OriginalPaper 15 April 2019 Pages: 1981 - 1986