1. Design and verification of a micro piezoelectric motor with energy harvesting characteristic for capsule endoscope

   • Chong Li
   • Rong Min
   • Chaodong Li

   OriginalPaper 03 October 2019 Pages: 4577 - 4582

2. Finite element model updating of jointed structure based on modal and strain frequency response function

   • Zhan Ming
   • Guo Qintao
   • Zhang Baoqiang

   OriginalPaper 03 October 2019 Pages: 4583 - 4593

3. A new dynamic balancing method of spindle based on the identification energy transfer coefficient

   • Xialun Yun
   • Xuesong Mei
   • Baomin Wang

   OriginalPaper 03 October 2019 Pages: 4595 - 4604

4. Identification of elastomeric isolator parameters on air-borne EO/IR camera with multi-axis gimbal

   • Sang-won Kim
   • Sung-kie Youn
   • Sang-eun Lee

   OriginalPaper 08 October 2019 Pages: 4605 - 4613

5. Identification of force coefficients in inter-shaft squeeze film dampers utilizing complex vector description and computational fluid dynamics

   • Gil Jun Lee
   • Jay Kim

   OriginalPaper 03 October 2019 Pages: 4615 - 4625

6. Analysis and design of a torsional vibration isolator for rotating shafts

   • Seong Mun Kim
   • Jung Ryeol Hong
   • Hong Hee Yoo

   OriginalPaper 03 October 2019 Pages: 4627 - 4634

7. Active control of harmonic noise propagated through openings of an enclosure with phase compensator

   • Jeong-Mo Ku
   • Weui-Bong Jeong
   • Chinsuk Hong

   OriginalPaper 03 October 2019 Pages: 4635 - 4644

8. Dynamic performance of a rotor system with an initial bow and coupling faults of imbalance-rub during whirling motion

   • Yang Yang
   • Yiren Yang
   • Dengqing Cao

   OriginalPaper 03 October 2019 Pages: 4645 - 4657

9. Comments on the stability of the synchronous states of three vibrators in a vibrating system with two rigid frames

   • Xueliang Zhang
   • Zhihui Wang
   • Jinlin Xu

   OriginalPaper 03 October 2019 Pages: 4659 - 4672

10. Vibration reduction against modulated excitation using multichannel NLMS algorithm for a structure with three active paths between plates

    • Dongwoo Hong
    • Byeongil Kim

    OriginalPaper 03 October 2019 Pages: 4673 - 4680

11. Influence of conical degree on the performance of radial and axial integrated auxiliary bearing for active magnetic bearing system

    • Chengtao Yu
    • Yuemei Sun
    • Wentao Shan

    OriginalPaper 03 October 2019 Pages: 4681 - 4687

12. Numerical and experimental analysis of hybrid lubrication regime for internal gear motor and pump

    • Trong Hoa Pham
    • Jürgen Weber
    • Dinh Tu Nguyen

    OriginalPaper 03 October 2019 Pages: 4689 - 4699

13. Experimental investigations into fretting wear and damage mechanisms of Inconel X-750 alloy

    • Ibrohim Rustamov
    • Fei Guo
    • Zixi Wang

    OriginalPaper 03 October 2019 Pages: 4701 - 4713

14. Finite element analysis and mathematical characterization of contact pressure distribution in bolted joints

    • Jianbin Cao
    • Zhousuo Zhang

    OriginalPaper 03 October 2019 Pages: 4715 - 4725

15. Fatigue strength prediction of TC4 titanium alloy following foreign object damage based on contour feature

    • X. T. Hu
    • Y. W. Wan
    • Y. D. Song

    OriginalPaper 03 October 2019 Pages: 4727 - 4734

16. Repairing cracked aluminum plates by aluminum patch using diffusion method

    • Sobhan Dehghanpour
    • Alireza Nezamabadi
    • Mehdi Tajdari

    OriginalPaper 03 October 2019 Pages: 4735 - 4743

17. NDE characterization and inspection techniques of trailing edges in wind turbine blades using terahertz waves

    • Kwang-Hee Im
    • Sun-Kyu Kim
    • Chien-Ping Chiou

    OriginalPaper 03 October 2019 Pages: 4745 - 4753

18. Development of PMMA/TiO₂ nanocomposites as excellent dental materials

    • Md. Alamgir
    • Ashis Mallick
    • Santosh K. Tiwari

    OriginalPaper 03 October 2019 Pages: 4755 - 4760

19. Homogenization-based multiscale analysis for equivalent mechanical properties of nonwoven carbon-fiber fabric composites

    • Haksung Lee
    • Chan-woong Choi
    • Ki-weon Kang

    OriginalPaper 08 October 2019 Pages: 4761 - 4770

20. Thrust force modelling and surface roughness optimization in drilling of AA-7075: FEM and GRA

    • Nafiz Yaşar

    OriginalPaper 03 October 2019 Pages: 4771 - 4781

21. Influence of roughness on the behavior of three-dimensional journal bearing based on fluid-structure interaction approach

    • Mohammad Tauviqirrahman
    • Brain Choirul Ichsan
    • Muchammad

    OriginalPaper 03 October 2019 Pages: 4783 - 4790

22. Crystal elasticity analysis of contact fatigue behavior of a wind turbine gear

    • Hao Zhou
    • Peitang Wei
    • Wei Wang

    OriginalPaper 03 October 2019 Pages: 4791 - 4802

23. A study on fracture behavior due to crack propagation at compact tension specimen composed of inhomogeneous metal materials with holes near crack

    • Kye Kwang Choi
    • Jung Ho Lee
    • Jae Ung Cho

    OriginalPaper 03 October 2019 Pages: 4803 - 4811

24. Creep deformation characteristics of microalloyed HP40Nb steel at 950 °C

    • Van Hung Dao
    • Jung Soo Song
    • Kee Bong Yoon

    OriginalPaper 03 October 2019 Pages: 4813 - 4821

25. Numerical study of wet-steam flow in Moore nozzles

    • Santhosh Senguttuvan
    • Jang-Chang Lee

    OriginalPaper 03 October 2019 Pages: 4823 - 4830

26. Optimum angles of non-standard diffusers and reducers for engineering application

    • Soon-Ho Choi
    • Sedong Kim
    • Hyomin Jeong

    OriginalPaper 03 October 2019 Pages: 4831 - 4841

27. Experimental and numerical study of the performance and cavitation flow of centrifugal pump with jetting device

    • Baoling Cui
    • Kaicheng Zhu
    • Peifeng Lin

    OriginalPaper 03 October 2019 Pages: 4843 - 4853

28. Optimization of pre-swirl nozzle shape and radial location to increase discharge coefficient and temperature drop

    • Hyungyu Lee
    • Jungsoo Lee
    • Jinsoo Cho

    OriginalPaper 03 October 2019 Pages: 4855 - 4866

29. An automatic multi-objective optimization tool for the optimum design of a cracked pressure vessel with composite coating

    • Seyed Mohammad Navid Ghoreishi
    • Mahdi Fakoor
    • Mohammad Aminjafari

    OriginalPaper 03 October 2019 Pages: 4867 - 4875

30. Improved trajectory similarity-based approach for turbofan engine prognostics

    • Cheng-Geng Huang
    • Hong-Zhong Huang
    • Tudi Huang

    OriginalPaper 03 October 2019 Pages: 4877 - 4890

31. Stress concentration around of pin-loaded hole in unidirectional multi-layered metallic matrix composite material

    • Sajjad Dehghanpour
    • Keivan Hosseini Safari
    • Mohammadmahdi Attar

    OriginalPaper 03 October 2019 Pages: 4891 - 4898

32. Isomorphic identification for kinematic chains using variable high-order adjacency link values

    • Leiying He
    • Faxin Liu
    • Chuanyu Wu

    OriginalPaper 03 October 2019 Pages: 4899 - 4907

33. The mesh density effect on stress intensity factor calculation using ABAQUS XFEM

    • Ji-Su Kim
    • Hyun-Jae Lee
    • Yong-Beum Kim

    OriginalPaper 03 October 2019 Pages: 4909 - 4916

34. Analysis of fluid flow and heat transfer of nanofluid inside triangular enclosure equipped with rotational obstacle

    • Ali Akbar Abbasian Arani
    • Mehrdad Kazemi

    OriginalPaper 03 October 2019 Pages: 4917 - 4929

35. FSW of low carbon steel using tungsten carbide (WC-10wt.%Co) based tool material

    • Avinish Tiwari
    • Piyush Singh
    • Sachin D. Kore

    OriginalPaper 03 October 2019 Pages: 4931 - 4938

36. A novel planar motion generation method based on the synthesis of planetary gear train with noncircular gears

    • Jun Ye
    • Xiong Zhao
    • XuDong Xia

    OriginalPaper 03 October 2019 Pages: 4939 - 4949

37. Performance model for tempered anti-glare LCD cover glass

    • Jeongju Choi

    OriginalPaper 03 October 2019 Pages: 4951 - 4956

38. Experimental fatigue life determination of thermo-diffusion surface boronized of AISI 1040 steel

    • Hacı Bekir Özerkan

    OriginalPaper 03 October 2019 Pages: 4957 - 4962

39. Modeling, analysis, and experiments of a pause-and-leap jumping robot during takeoff, flight, and landing buffering

    • Qi Yang
    • Jing Zhao
    • Xingkun Liu

    OriginalPaper 03 October 2019 Pages: 4963 - 4979

40. A bundled staggering patterned pneumatic muscle actuator for improved working efficiency

    • Hyuk Jin Lee
    • Kyeong Ha Lee
    • Ja Choon Koo

    OriginalPaper 03 October 2019 Pages: 4981 - 4989

41. Inertia matching analysis of a 5-DOF hybrid optical machining manipulator

    • Yixuan Kong
    • Gang Cheng
    • Laibin Zhang

    OriginalPaper 03 October 2019 Pages: 4991 - 5002

42. Effects of component geometries and inflow conditions on ejector operational mode

    • Sang Hun Kang
    • Jae Gang Kim
    • Hyuck-Joon Namkoung

    OriginalPaper 03 October 2019 Pages: 5003 - 5008

43. Thermal modelling and design of dynamically-controlled heater plates for high temperature processing of 300 mm wafers

    • Dae Seong Woo
    • Changwoon Han
    • Kyoung Joon Kim

    OriginalPaper 03 October 2019 Pages: 5009 - 5016

44. Heat transfer and flow field features between surface mounted trapezoidal-ribs

    • Md Shaukat Ali
    • Naveen Sharma
    • Andallib Tariq

    OriginalPaper 03 October 2019 Pages: 5017 - 5023

45. Experimental study of the seawater fouling on a plate-frame heat exchanger for utilization of waste heat from powerplant

    • Wonkeun Baik
    • Rin Yun
    • Jaehyeok Heo

    OriginalPaper 03 October 2019 Pages: 5025 - 5032

46. Equivalence ratio variation and combustion instability in hybrid rocket

    • Dong Eun Lee
    • Changjin Lee

    OriginalPaper 03 October 2019 Pages: 5033 - 5042

47. Analysis of the electric drive mode use and energy flow in hybrid drives of SUVs in urban and extra-urban traffic conditions

    • Ireneusz Pielecha
    • Wojciech Cieślik
    • Jerzy Merkisz

    OriginalPaper 03 October 2019 Pages: 5043 - 5050

48. A numerical study on NO_x formation behavior in a lean-premixed gas turbine combustor using CFD-CRN method

    • Truc Huu Nguyen
    • Jungkyu Park
    • Shaun Kim

    OriginalPaper 03 October 2019 Pages: 5051 - 5060

49. Experimental and numerical investigation on a novel gas turbocharging system for diesel engine power recovery at high altitude

    • Dengfeng Yang
    • Li’ang Cao
    • Zhilian Zhang

    OriginalPaper 08 October 2019 Pages: 5061 - 5072

50. Experimental study on ignition characteristic of gasoline-biodiesel blended fuel in a constant-volume chamber

    • Dinh Nam Vu
    • Ocktaeck Lim

    OriginalPaper 03 October 2019 Pages: 5073 - 5083