An effective health indicator based on two dimensional hidden Markov model Lin LiTingfeng MingShuai Zhang OriginalPaper 23 April 2017 Pages: 1543 - 1550
Vibrational behavior of MDOF oscillators subjected to multiple contact constraints Mo FadaeeShudong Yu OriginalPaper 23 April 2017 Pages: 1551 - 1560
Dynamic stress of impeller blade of shaft extension tubular pump device based on bidirectional fluid-structure interaction Kan KanYuan ZhengXin Zhang OriginalPaper 23 April 2017 Pages: 1561 - 1568
Load and dynamic characteristic analysis of wind turbine flexible blades Juchuan DaiWei HuXiangbin Shen OriginalPaper 23 April 2017 Pages: 1569 - 1580
A study on the automatic harvest by on-off control for a combined system of continuous culture of microalgae and ultrasonic separation devices Jae Hyeok KimSang Hwa Jeong OriginalPaper 23 April 2017 Pages: 1581 - 1586
Low-speed rolling bearing fault diagnosis based on EMD denoising and parameter estimate with alpha stable distribution Qing XiongYanhai XuLan Tang OriginalPaper 23 April 2017 Pages: 1587 - 1601
Crack growth pattern prediction in a thin walled cylinder based on closed form thermo-elastic stress intensity factors Mohammad Abbaspour NiasaniRahmatollah GhajarSeyed Mohammad Hossein Sharifi OriginalPaper 23 April 2017 Pages: 1603 - 1610
Development of a cold wire-feed additive layer manufacturing system using shaped metal deposition method Oguzhan YilmazAdnan A. Ugla OriginalPaper 23 April 2017 Pages: 1611 - 1620
Optimization of mixing process and effect of multi-walled carbon nanotubes on tensile properties of unsaturated polyester resin in composite materials Van-Tho HoangYoung-Jin Yum OriginalPaper 23 April 2017 Pages: 1621 - 1627
Fracture analysis of woven textile composite using cohesive zone modeling Kyeongsik Woo OriginalPaper 23 April 2017 Pages: 1629 - 1637
Evaluating the reliability of the cylinder liner of a low-speed marine engine subjected to high-cycle fatigue with high mean stress Jeong-Hwan LeeDong-Won JangSoon-Bok Lee OriginalPaper 23 April 2017 Pages: 1639 - 1644
Investigation on aerodynamics and active flow control of a vertical axis wind turbine with flapped airfoil Yang YangChun LiQuanyong Yuan OriginalPaper 23 April 2017 Pages: 1645 - 1655
Numerical investigation of non-uniform magnetic field effects on the blood velocity and magnetic nanoparticles concentration inside the vessel S. M. A. Ne’matiM. GhassemiA. Shahidian OriginalPaper 23 April 2017 Pages: 1657 - 1663
Linear stability analysis of Rayleigh-Bénard convection of cold water near its density maximum in a vertically heated annular container Xiao-Ran MaLi ZhangYou-Rong Li OriginalPaper 23 April 2017 Pages: 1665 - 1672
A study on improving bone conduction speaker performance by electromagnetic prediction and performance distribution by statistical analysis method Dong Shin KoDeog Jae HurJai Hyuk Lee OriginalPaper 23 April 2017 Pages: 1673 - 1681
Flow structure of conical distributed multiple gas jets injected into a water chamber Jiajun ZhaoYonggang Yu OriginalPaper 23 April 2017 Pages: 1683 - 1691
A study of the performance of a radial diffuser for a multistage high-pressure pump Deok Su KimSanjar MamatovWarn Gyu Park OriginalPaper 23 April 2017 Pages: 1693 - 1700
A new method for reducing VOCs formation during crude oil loading process Hamid Reza KarbasianDae Yeon KimKyung Chun Kim OriginalPaper 23 April 2017 Pages: 1701 - 1710
Numerical simulations of the internal flow pattern of a vortex pump compared to the Hamel-Oseen vortex Angela GerlachEnrico PreussFlemming Lykholt-Ustrup OriginalPaper 23 April 2017 Pages: 1711 - 1719
Numerical investigation of an Organic Rankine cycle radial inflow two-stage turbine F. HamdiJ. SeoS. Han OriginalPaper 23 April 2017 Pages: 1721 - 1728
Large Eddy simulation of turbulent flow past a circular cylinder in the subcritical and critical regimes Kyongjun LeeKyung-Soo Yang OriginalPaper 23 April 2017 Pages: 1729 - 1737
A solver for massively parallel direct numerical simulation of three-dimensional multiphase flows Seungwon ShinJalel CherguiDamir Juric OriginalPaper 23 April 2017 Pages: 1739 - 1751
Secondary flow stabilization of 100 kW-class micro gas turbine Hyung-Soo LimJe-Sung BangByung Ok Kim OriginalPaper 23 April 2017 Pages: 1753 - 1761
Develop a new method to reliability determination of a solar array mechanism via universal generating function Mohammad Ali Farsi OriginalPaper 23 April 2017 Pages: 1763 - 1771
Thermo-electro-mechanical buckling analysis of cylindrical nanoshell on the basis of modified couple stress theory Fahimeh MehralianYaghoub Tadi Beni OriginalPaper 23 April 2017 Pages: 1773 - 1787
Fatigue strength evaluation of a welded structure by a concentrated load close to the welded joint Y. K. ParkJ. G. Shin OriginalPaper 23 April 2017 Pages: 1789 - 1796
Design optimization of a drifter using the Taguchi method for efficient percussion drilling Changheon SongJintai ChungJoo-Young Oh OriginalPaper 23 April 2017 Pages: 1797 - 1803
Stress analysis of compound cylinders subjected to thermo-mechanical loads Kaoutar BahoumMohammed DianyMustapha Mabrouki OriginalPaper 23 April 2017 Pages: 1805 - 1811
Stochastic analysis of thin plates on elastic foundation by combining the generalized polynomial chaos and element free Galerkin method Ehsan BahmyariMohammad Reza Khedmati OriginalPaper 23 April 2017 Pages: 1813 - 1824
Buckling of single-walled carbon nanotubes with and without defects Jozef BockoPavol Lengvarský OriginalPaper 23 April 2017 Pages: 1825 - 1833
Numerical simulation of the combination effect of external magnetic field and rotating workpiece on abrasive flow finishing Saeid KheradmandMojtaba EsmailianA. Fatahy OriginalPaper 23 April 2017 Pages: 1835 - 1841
Production of electrolyzed water for home-use based on electrodeposited macroporous platinum Soobyeong Kim OriginalPaper 23 April 2017 Pages: 1843 - 1849
Comparison between wire mesh and plate electrodes during wide-pattern machining on invar fine sheet using through-mask electrochemical micromachining Kwang-ho ChunDa-som JinEun-sang Lee OriginalPaper 23 April 2017 Pages: 1851 - 1859
Influence of cutting temperature on carbon fiber-reinforced plastic composites in high-speed machining Seok Jae HaKi Beom KimMyeong Woo Cho OriginalPaper 23 April 2017 Pages: 1861 - 1867
Design of a piston forging process using a hybrid Taguchi method and multiple criteria decision-making Hong-Seok ByunSeok-Hee Lee OriginalPaper 23 April 2017 Pages: 1869 - 1876
Surface quality prediction model of nano-composite ceramics in ultrasonic vibration-assisted ELID mirror grinding Bo ZhaoFan ChenXiao-bo Wang OriginalPaper 23 April 2017 Pages: 1877 - 1884
Development of concurrent stamping-piercing trimless hot stamping process In-Kyu LeeSung-Yun LeeSang-Kon Lee OriginalPaper 23 April 2017 Pages: 1885 - 1891
Step-and-repeat stamping method for the generation of large-area microscale wrinkle patterns Zhi-jun ZhaoJeong-ho YangSang-hu Park OriginalPaper 23 April 2017 Pages: 1893 - 1898
Camera-based measurement for close-distance relative vessel positioning Yoshiaki MizuchilTadashi OguraYongwoon Choi OriginalPaper 23 April 2017 Pages: 1899 - 1907
Efficient walking gait with different speed and step length: Gait strategies discovered by dynamic optimization of a biped model Kang AnChuanjiang LiChengju Liu OriginalPaper 23 April 2017 Pages: 1909 - 1919
The effect on deflection of steel diaphragm of pressure sensor due to change in boundary condition in the welded region Pradipta Vaskar BiswasHwa Young KimJung Hwan Ahn OriginalPaper 23 April 2017 Pages: 1921 - 1925
Kinematics analysis of a novel planar parallel manipulator with kinematic redundancy Haibo QuSheng Guo OriginalPaper 23 April 2017 Pages: 1927 - 1935
Natural convection of nanofluid in a wavy cavity in the presence of magnetic field on variable heat surface temperature Korosh JavaherdehMehdi MoslemiMona Shahbazi OriginalPaper 23 April 2017 Pages: 1937 - 1945
A new component map generation method for gas turbine adaptation performance simulation Qingcai YangShuying LiYunpeng Cao OriginalPaper 23 April 2017 Pages: 1947 - 1957
Wettability characterization of pore networks of gas diffusion layers in proton exchange membrane fuel cells Yongtaek Lee OriginalPaper 23 April 2017 Pages: 1959 - 1968
Effects of injection rate on combustion and emissions of a pilot ignited direct injection natural gas engine Qian WangChangsheng ShaoZhixia He OriginalPaper 23 April 2017 Pages: 1969 - 1978
Feasibility of a new non-edible feedstock in diesel engine: Investigation of performance, emission and combustion characteristics Paramvir SinghVarunS. R. Chauhan OriginalPaper 23 April 2017 Pages: 1979 - 1986
Flow and heat transfer characteristics of alkali metal liquid in a pipe with inscribed regular polygon porous media Lan XiaoHai-Yan WuShuang-Ying Wu OriginalPaper 23 April 2017 Pages: 1987 - 1994
Thermal performance of a vapor chamber for electronic cooling applications Jefferson Raja BoseNizar AhammedLazarus Godson Asirvatham OriginalPaper 23 April 2017 Pages: 1995 - 2003
Sensitivity analysis and chemical reaction mechanism simplification of blast furnace gas in gas turbine combustor environment Zhao YangXiangsheng LiLian Lu OriginalPaper 23 April 2017 Pages: 2005 - 2014