On the characteristics of an ultra-low frequency nonlinear isolator using sliding beam as negative stiffness Xiuchang HuangXintian LiuHongxing Hua OriginalPaper 14 March 2014 Pages: 813 - 822
Crack detection in a beam with an arbitrary number of transverse cracks using genetic algorithms N. KhajiM. Mehrjoo OriginalPaper 14 March 2014 Pages: 823 - 836
Effect of parameters on roll dynamic response of an articulated vehicle carrying liquids Shahram AzadiAli JafariMasoud Samadian OriginalPaper 14 March 2014 Pages: 837 - 848
Effects of shear deformation and rotary inertia on the natural frequencies of axially loaded beams Kyo-Nam Koo OriginalPaper 14 March 2014 Pages: 849 - 857
A study on the design of a new power transmission for wind turbines Seong Keol Kim OriginalPaper 14 March 2014 Pages: 859 - 866
Aluminum 6060-T6 friction stir welded butt joints: fatigue resistance with different tools and feed rates S. BaragettiG. D’Urso OriginalPaper 14 March 2014 Pages: 867 - 877
Board level reliability analysis of chip resistor assemblies under thermal cycling: A comparison study between SnPb and SnAgCu Changwoon HanBongtae Han OriginalPaper 14 March 2014 Pages: 879 - 886
Cold-flow patterns behind novel rifled bluff-body cones Kuo C. SanChih L. ShihShun C. Yen OriginalPaper 14 March 2014 Pages: 887 - 894
Analysis and measurement of the impact of diffuser width on rotating stall in centrifugal compressors Yong-Sang YoonSeung Jin Song OriginalPaper 14 March 2014 Pages: 895 - 905
Characteristic test methods of the thermal mass flow controller Yong Moon ChoiHae Man ChoiWoong Kang OriginalPaper 14 March 2014 Pages: 907 - 914
A newly developed rotor profile for lobe pumps: Generation and numerical performance assessment Yaw-Hong KangHa-Hai Vu OriginalPaper 14 March 2014 Pages: 915 - 926
Active control of impinging jet for modification of mixing Jungwoo Kim OriginalPaper 14 March 2014 Pages: 927 - 935
Effects of contraction-type impeller on non-overloaded performance for low-specific-speed sewage pump Hua ZhangBin ChenWei-dong Cao OriginalPaper 14 March 2014 Pages: 937 - 944
Comparison of DNS and Reynolds stress modelling of flow around a rotating cylinder Klaus BremhorstMatthew BrennanKyung-Soo Yang Invited Paper 14 March 2014 Pages: 945 - 951
A cam-quadrilateral mechanism for power transmission of a twin-rotor piston engine Xiaojun XuHao DengHaijun Xu OriginalPaper 14 March 2014 Pages: 953 - 961
Optimal combination of design parameters for improving the kinematics characteristics of a midsize truck through design of experiment Bo Myung KimJae Won KimChae Youn Oh OriginalPaper 14 March 2014 Pages: 963 - 969
A study on the development of image analysis instrument and estimation of mass, volume and center of gravity using CT image in Korean Seong-Bin ParkSa-Yup KimKyung-Ryul Chung OriginalPaper 14 March 2014 Pages: 971 - 977
A phenomenological constitutive model for the pseudoelastic behavior of shape memory alloys Kwangsoo Ho OriginalPaper 14 March 2014 Pages: 979 - 988
Teaching conceptual design using axiomatic design to engineering students and practitioners Gyung-Jin Park OriginalPaper 14 March 2014 Pages: 989 - 998
Experimental and numerical crashworthiness investigation of combined circular and square sections Mohammad Hasan ShojaeefardAmir NajibiMohsen Yeganeh OriginalPaper 14 March 2014 Pages: 999 - 1006
Novel steel wheel design based on multi-objective topology optimization Denghong XiaoHai ZhangYingchun Shan OriginalPaper 14 March 2014 Pages: 1007 - 1016
Modeling of laser thermal and hydrodynamic effects on a dilute suspension of micro-particles in water Mohammad ZabetianMohammad Hassan SaidiMohammad Behshad Shafii OriginalPaper 14 March 2014 Pages: 1017 - 1026
Experimental study on fabrication and evaluation of a micro-scale shaft grinding tool Y. D. GongX. L. WenC. Wang OriginalPaper 14 March 2014 Pages: 1027 - 1037
Three-phase modeling of viscoelastic nanofiber-reinforced matrix Fatemeh FatemifarManouchehr SalehiNaser Kordani OriginalPaper 14 March 2014 Pages: 1039 - 1044
Optimization of machining parameters for EDM operations based on central composite design and desirability approach Subramanian GopalakannanThiagarajan Senthilvelan OriginalPaper 14 March 2014 Pages: 1045 - 1053
Genetic algorithm-based hysteresis modeling and identification of rotary SMA actuators Van Phu DoPhi Luan NguyenByung Ryong Lee OriginalPaper 14 March 2014 Pages: 1055 - 1063
A study on the control system design for ship mooring winch system Youngbok Kim OriginalPaper 14 March 2014 Pages: 1065 - 1072
Heat transfer analysis in PCM-filled RCC roof for thermal management P. S. S. SrinivasanM. Ravikumar OriginalPaper 14 March 2014 Pages: 1073 - 1078
Experimental and numerical study of piston thermal management using piston cooling jet Mohammad Izadi NajafabadiMostafa MirsalimShahabeddin Alaviyoun OriginalPaper 14 March 2014 Pages: 1079 - 1087
Experimental study of fine center electrode spark plug in bi-fuel engines Saeed JavanSyed Shahabodin AlaviyounF. Ommi OriginalPaper 14 March 2014 Pages: 1089 - 1097
A review of metallic radiation recuperators for thermal exhaust heat recovery Harshdeep SharmaAnoop KumarSourabh Khurana OriginalPaper 14 March 2014 Pages: 1099 - 1111
Steel billet reheat simulation with growth of oxide layer and investigation on zone temperature sensitivity Satish Kumar DubeyP. Srinivasan OriginalPaper 14 March 2014 Pages: 1113 - 1124
Pressure dependence of mass burning rates in diluent premixed flames of H2/O2 at high pressures Chae Hoon Sohn OriginalPaper 14 March 2014 Pages: 1125 - 1133
Erratum to “Optimal design of linear vibrators used in touch screen mobile phones” Jin-Hun ParkPeng SunSang-Moon Hwang Erratum 14 March 2014 Pages: 1135 - 1135
Erratum to “The flight test and power simulations of an UAV powered by solar cells, a fuel cell and batteries” Bohwa LeePoomin ParkSejin Kwon Erratum 14 March 2014 Pages: 1137 - 1137
