1. Maximum height of an obstacle overcome by a wheeled vehicle

   • G. I. Mamiti
   • S. Kh. Pliev
   • E. K. Gutiev

   OriginalPaper 05 July 2014 Pages: 351 - 352

2. Relation between the fluctuations in hole shape and position before and after reaming

   • S. G. Andreeva
   • G. S. Zheleznov
   • V. G. Krutsilo

   OriginalPaper 05 July 2014 Pages: 353 - 356

3. Optimal ram extrusion of wood-plastic composites

   • A. N. Ekimenko

   OriginalPaper 05 July 2014 Pages: 357 - 361

4. Predicting the life of chain transmissions

   • S. A. Metil’kov
   • S. B. Berezhnoi

   OriginalPaper 05 July 2014 Pages: 362 - 365

5. Theoretical aspects of technological mechanics. 9. Strain and accumulated strain. Part 1

   • A. L. Vorontsov

   OriginalPaper 05 July 2014 Pages: 366 - 373

6. Geometric shaping in cutting

   • Yu. E. Petukhov
   • N. V. Kolesov
   • S. Yu. Yurasov

   OriginalPaper 05 July 2014 Pages: 374 - 380

7. Predicting the limiting state of a multiblade hard-alloy tool

   • E. G. Krylov
   • A. V. Belova

   OriginalPaper 05 July 2014 Pages: 381 - 385

8. Surface plastic deformation of an applied metal layer

   • V. A. Korotkov

   OriginalPaper 05 July 2014 Pages: 386 - 388

9. A methodological error in analyzing the forces within a frictional pair

   • I. K. Aleksandrov

   OriginalPaper 05 July 2014 Pages: 389 - 392

10. Dynamic characteristics of the supporting system in a horizontal-drilling machine

    • Yu. V. Kirilin
    • E. A. Spiridonov

    OriginalPaper 05 July 2014 Pages: 393 - 395

11. High-efficiency axial cutting tools

    • Yu. P. Burochkin

    OriginalPaper 05 July 2014 Pages: 396 - 399

12. Quality control in the production of metal-cutting tools

    • Yu. I. Rudometov

    OriginalPaper 05 July 2014 Pages: 400 - 401

13. Determining the maximum-performance temperature of hard-alloy cutting plates

    • E. V. Artamonov
    • D. S. Vasilega
    • A. M. Tveryakov

    OriginalPaper 05 July 2014 Pages: 402 - 403

14. Determining the optimal cutting speed in turning by composite cutters on the basis of the chip

    • E. V. Artamonov
    • D. V. Vasil’ev

    OriginalPaper 05 July 2014 Pages: 404 - 405

15. Compensation of the pitch errors in helical gears

    • A. N. Vasin
    • B. M. Iznairov
    • G. Kh. Mukatova

    OriginalPaper 05 July 2014 Pages: 406 - 409

16. Influence of the heat transfer in the finishing of high-speed steel on the residual-stress distribution

    • F. Ya. Barats
    • A. V. Kochetkov

    OriginalPaper 05 July 2014 Pages: 410 - 413

17. Mathematical models of the axial cutting forces in the broaching of structural carbon and alloy steel

    • Yu. N. Seleznev
    • V. S. Gubanov
    • L. V. Khoroshilova

    OriginalPaper 05 July 2014 Pages: 414 - 416

18. Special-purpose equipment

    • V. M. Vorob’ev

    OriginalPaper 05 July 2014 Pages: 417 - 422

19. Surface-layer quality after high-speed turning of hard material

    • I. E. Kiryushin
    • D. E. Kiryushin
    • D. V. Terin

    OriginalPaper 05 July 2014 Pages: 423 - 424