1. Cyclic degradation of material in vehicle components

   • V. I. Mironov
   • O. A. Lukashuk
   • G. G. Kozhushko

   OriginalPaper 17 June 2012 Pages: 417 - 422

2. Improved rotary stretching and softening equipment for the leather industry

   • F. U. Nigmatova
   • D. I. Shin
   • B. B. Akhmedov

   OriginalPaper 17 June 2012 Pages: 423 - 425

3. Operation of a centrifugal pump and a liquid ejector with an isobaric mixing chamber

   • V. Yu. Aleksandrov
   • K. K. Klimovskii

   OriginalPaper 17 June 2012 Pages: 426 - 429

4. Control system for a machine-tool drive with compensation of spindle eccentricity

   • V. P. Legaev
   • L. K. Generalov

   OriginalPaper 17 June 2012 Pages: 430 - 432

5. Operation of two induction motors on a dissipative elastic base

   • B. A. Gordeev
   • A. V. Leont’eva

   OriginalPaper 17 June 2012 Pages: 433 - 437

6. Optimizing cyclic gearless electric drives with a reduced-speed section

   • A. V. Sapsalev

   OriginalPaper 17 June 2012 Pages: 438 - 443

7. High-strength antifrictional elastoplastic slip bearings for shipbuilding and the power industry

   • A. S. Oryshchenko
   • V. E. Bakhareva
   • I. V. Lishevich

   OriginalPaper 17 June 2012 Pages: 444 - 448

8. Thermoelastic contact instability with mixed lubrication in frictional components of vehicles

   • I. A. Medelyaev

   OriginalPaper 17 June 2012 Pages: 449 - 453

9. A new method of solving complex variational problems: Examples of the determination of broaching parameters

   • A. L. Vorontsov

   OriginalPaper 17 June 2012 Pages: 454 - 463

10. Crack resistance of tool coatings in continuous cutting

    • V. P. Tabakov

    OriginalPaper 17 June 2012 Pages: 464 - 468

11. Working kinematic front angle in turning a sinusoidal linear surface

    • V. V. Vorona
    • I. A. Shchurov

    OriginalPaper 17 June 2012 Pages: 469 - 472

12. Influence of thermal loads on the stress-strain state of aluminum-oxide ceramic cutting plates

    • S. N. Grigor’ev
    • V. V. Kuzin
    • A. D. Batako

    OriginalPaper 17 June 2012 Pages: 473 - 477

13. Damping-system design on the basis of electrochemical modules

    • Yu. A. Pozhidaev
    • V. I. Kadoshnikov

    OriginalPaper 17 June 2012 Pages: 478 - 481

14. Structural precision of metal-cutting machines

    • A. P. Kuznetsov
    • M. G. Kosov

    OriginalPaper 17 June 2012 Pages: 482 - 490

15. Simulation of hydraulic machine-tool drives

    • Ya. A. Darsht
    • A. M. Filippov

    OriginalPaper 17 June 2012 Pages: 491 - 495

16. Vibrational tests of lathes

    • V. V. Yurkevich

    OriginalPaper 17 June 2012 Pages: 496 - 497

17. High-speed honing tool for deep holes

    • V. A. Bakhvalov

    OriginalPaper 17 June 2012 Pages: 498 - 500

18. Thermomagnetic effect in the chemicothermal surface hardening of ceramic cutting plates

    • V. N. Puchkin
    • V. G. Solonenko
    • L. A. Solonenko

    OriginalPaper 17 June 2012 Pages: 501 - 503

19. Hybrid machining in the creation of specified residual stress in the surface layer

    • E. S. Kiselev
    • E. N. Leksin
    • O. V. Blagovskii

    OriginalPaper 17 June 2012 Pages: 504 - 507

20. Combined finishing and hardening in the surface plastic deformation of a plunger by diamond smoothing

    • A. S. Kilov

    OriginalPaper 17 June 2012 Pages: 508 - 510

21. High-speed grinding of ZhS6-K high-temperature nickel alloy

    • A. Yu. Popov
    • D. S. Rechenko
    • V. A. Sergeev

    OriginalPaper 17 June 2012 Pages: 511 - 512

22. Dimensional analysis of plate heating

    • V. G. Miroshnichenko
    • V. N. Syrovatka

    OriginalPaper 17 June 2012 Pages: 513 - 514

23. Calculation of errors in hole machining by ansys software

    • S. V. Sergeev
    • D. V. Proshunin
    • Yu. S. Sergeev

    OriginalPaper 17 June 2012 Pages: 515 - 518