1. Influence of contact stress on the life of connected elements

   • G. G. Zaveryukha

   OriginalPaper 17 February 2010 Pages: 1 - 6

2. Contact-strength estimates of the reliability of conical gears with limited statistical information

   • V. S. Utkin

   OriginalPaper 17 February 2010 Pages: 7 - 10

3. Simulating the dynamic reaction of manipulator supports

   • A. A. Dobrachev
   • L. T. Raevskaya
   • A. V. Shvets

   OriginalPaper 17 February 2010 Pages: 11 - 16

4. Contact stress of connected axisymmetric cylindrical shells of different length in contact-pressure discontinuity zones

   • A. M. Rubin

   OriginalPaper 17 February 2010 Pages: 17 - 19

5. Edge contact in conical transmissions with round gear teeth

   • V. N. Rubtsov

   OriginalPaper 17 February 2010 Pages: 20 - 22

6. Fatigue strength of materials in a complex stress state

   • A. E. Tsybul’ko
   • E. A. Romanenko

   OriginalPaper 17 February 2010 Pages: 23 - 25

7. Frictional properties of aluminum bronze facings

   • V. V. Karzhavin
   • L. T. Plaksina
   • B. A. Potekhin

   OriginalPaper 17 February 2010 Pages: 26 - 30

8. Automatic discontinuous 2 transmission lines with sections of different productivity (q ₁ < q ₂)

   • V. S. Gorchev

   OriginalPaper 17 February 2010 Pages: 31 - 37

9. Open optimization in two-dimensional lathe control systems

   • V. P. Legaev
   • L. K. Generalov

   OriginalPaper 17 February 2010 Pages: 38 - 40

10. Pass-through lathe cutter with independent cutting systems

    • V. P. Cherkashin

    OriginalPaper 17 February 2010 Pages: 41 - 44

11. Theory of constrained cutting: chip formation with a developed plastic-deformation zone

    • S. I. Petrushin
    • A. V. Proskokov

    OriginalPaper 17 February 2010 Pages: 45 - 50

12. Precision basing of blanks with holes on cylindrical and truncated pins

    • F. N. Abramov

    OriginalPaper 17 February 2010 Pages: 51 - 60

13. Temperature in contact zone during shot hardening

    • I. G. Shin

    OriginalPaper 17 February 2010 Pages: 61 - 63

14. Development of a new theory of thermal cutting processes 1. basic principles

    • A. L. Vorontsov
    • N. M. Sultan-Zade
    • A. I. Savkin

    OriginalPaper 17 February 2010 Pages: 64 - 66

15. More efficient use of CAE systems in machine tool design

    • A. N. Polyakov
    • S. V. Kamenev

    OriginalPaper 17 February 2010 Pages: 67 - 71

16. Finite-element calculation of the dynamic characteristics of the supporting system of a special wheel-boring machine

    • Yu. V. Kirilin
    • N. V. Eremin

    OriginalPaper 17 February 2010 Pages: 72 - 76

17. Improving the dynamic precision of the tool position in a machining center

    • V. E. Lysov
    • Ya. I. Peshev

    OriginalPaper 17 February 2010 Pages: 77 - 80

18. Efficiency of numerically controlled metal-cutting machines

    • Ya. L. Liberman

    OriginalPaper 17 February 2010 Pages: 81 - 83

19. Influence of the composition of three-element nitride coatings on the state and wear of a cutting tool

    • V. P. Tabakov
    • A. V. Chikhranov

    OriginalPaper 17 February 2010 Pages: 84 - 89

20. Influence of the number of segments and their dimensional errors on the primary imbalance vector of a grinding wheel

    • V. G. Gusev
    • R. V. Zhigalov

    OriginalPaper 17 February 2010 Pages: 90 - 93

21. Tool management systems

    • N. A. Chemborisov
    • R. M. Khisamutdinov
    • D. R. Akhmetzyanov

    OriginalPaper 17 February 2010 Pages: 94 - 96

22. Basing precision of disk and bush blanks in multipoint machining

    • F. N. Abramov

    OriginalPaper 17 February 2010 Pages: 97 - 98

23. Machining of housing components in attachments with aerostatic bearings

    • A. V. Lut’yanov

    OriginalPaper 17 February 2010 Pages: 99 - 101

24. Precision of duplicate-milling machine with a spherical head

    • Yu. A. Novoselov

    OriginalPaper 17 February 2010 Pages: 102 - 103