Calculating the wear resistance of metals in frictional pairs 3. Calculating the wear rate of steel in roller pairs with rolling friction and slip A. M. Ryakhovskii OriginalPaper 29 August 2008 Pages: 733 - 740
Influence of wear of a roller drive chain on transmission fitness S. A. Metil’kovV. V. Yunin OriginalPaper 29 August 2008 Pages: 741 - 745
Turbine vibration with a pulsed kinematic perturbation V. F. Shatokhin OriginalPaper 29 August 2008 Pages: 746 - 753
Influence of coiling on the carrying capacity of vertical tanks A. V. DidkovskiiYa. M. KlebanovA. N. Davydov OriginalPaper 29 August 2008 Pages: 754 - 758
Dynamic operational stability of measuring and control systems based on vibrocontact measurements G. M. TrompetA. Ya. Krasil’nikov OriginalPaper 29 August 2008 Pages: 759 - 761
Semiperiodic screening of a rotating plane wing S. A. Gerasimov OriginalPaper 29 August 2008 Pages: 762 - 763
Contact friction in the deformation zone during ultrasonic surface plastic deformation T. M. Gavrilova OriginalPaper 29 August 2008 Pages: 764 - 768
Ensuring the reliability of liquid-friction bearings for rolling mills A. A. ZyuzinB. N. Kaz’min OriginalPaper 29 August 2008 Pages: 769 - 774
Cutting of corrosion-resistant steel using a tool with a short front surface A. I. Sedel’nikov OriginalPaper 29 August 2008 Pages: 775 - 778
Milling complex surfaces on a numerically controlled machine tool N. V. KolesovS. Yu. Yurin OriginalPaper 29 August 2008 Pages: 779 - 781
Brittle tensosensitive coatings for determining the stress-strain state of parts and structures A. N. SalinA. I. Dolinnyi OriginalPaper 29 August 2008 Pages: 782 - 785
Development of a new theory of cutting 8. Chip-breaker design A. L. VorontsovN. M. Sultan-ZadeA. Yu. Albagachiev OriginalPaper 29 August 2008 Pages: 786 - 792
Bauschinger effect in complex machining methods A. V. ShchedrinV. V. Ul’yanovA. A. Bekaev OriginalPaper 29 August 2008 Pages: 797 - 799
Minimizing the space occupied by multicoordinate gear-cutting machine tools for the manufacture of conical and hypoid transmissions L. I. SheikoS. Ya. Prikazchikov OriginalPaper 29 August 2008 Pages: 801 - 803
Self-adjusting guide pieces based on a rigid center V. B. Il’itskiiV. V. Moiseev OriginalPaper 29 August 2008 Pages: 804 - 808
End machining of teeth by a single-turn worm mill N. A. ChemborisovA. G. Kondrashov OriginalPaper 29 August 2008 Pages: 809 - 811
Selecting rational geometric parameters of a disk mill in machining high-temperature nickel powder alloys A. V. Kovalevskii OriginalPaper 29 August 2008 Pages: 812 - 813
Margin in sharpening helical channels of tool A. D. BalandinB. D. Danilenko OriginalPaper 29 August 2008 Pages: 814 - 815
X-ray microspectral analysis of ceramic binder and its contact zones with silicon-carbide grains I. V. NadeevaN. V. Nosenko OriginalPaper 29 August 2008 Pages: 816 - 820
Automating the design of technological processes S. A. Volkov OriginalPaper 29 August 2008 Pages: 821 - 824
Functional-technological approach to selection criteria for equipment A. V. MukhinV. V. Petrov OriginalPaper 29 August 2008 Pages: 825 - 828
Forces and contact temperature in plane end grinding by composite wheels S. M. Mikhailin OriginalPaper 29 August 2008 Pages: 829 - 832
Ensuring surface-layer quality in plane grinding of high-temperature nickel alloys V. F. Bez”yazychnyiB. M. DrapkinM. A. Prokof’ev OriginalPaper 29 August 2008 Pages: 833 - 835
More efficient deep grinding O. G. BykadorovaV. M. Shumyacher OriginalPaper 29 August 2008 Pages: 836 - 837
Improving the structure of an abrasive tool without binder Yu. N. PolyanchikovM. Yu. PolyanchikovaA. L. Plotnikov OriginalPaper 29 August 2008 Pages: 838 - 838
