Finite element simulation of deformation behavior in friction welding of Al-Cu-Mg alloy Li QinghuaLi FuguoWan Qiong OriginalPaper 01 December 2006 Pages: 627 - 631
Modification of a thermomechanical model to predict constitutive behavior of Al-Mg-Si alloys J. van de LangkruisW. H. KoolS. van der Zwaag OriginalPaper 01 December 2006 Pages: 632 - 639
Modeling the viscosity versus temperature and pressure of light hydrocarbon solvents Adango MiadonyeLoree D’Orsay OriginalPaper 01 December 2006 Pages: 640 - 645
Recrystallization texture characteristic and drawability of a warm rolled and cold rolled interstitial-free steel Zhaodong WangYanhui GuoPeng Zhang OriginalPaper 01 December 2006 Pages: 646 - 650
Determinations of the non-recrystallization temperature for X52 steel produced by compact slab process combined with direct hot rolling Ahmed Ismail Zaky OriginalPaper 01 December 2006 Pages: 651 - 655
Dry sliding wear behavior of metal matrix composites: A statistical approach S. BasavarajappaG. Chandramohan OriginalPaper 01 December 2006 Pages: 656 - 660
Evaluating the berkovitz method to predict fatigue loads in mechanical failure investigations C. O. F. T. RuckertJ. R. TarpaniD. Spinelli OriginalPaper 01 December 2006 Pages: 661 - 667
Dry sliding wear behavior of Al 2219/SiCp-Gr hybrid metal matrix composites S. BasavarajappaG. ChandramohanM. Prabu OriginalPaper 01 December 2006 Pages: 668 - 674
Hole expansion in a variety of sheet steels R. J. ComstockD. K. ScherrerR. D. Adamczyk OriginalPaper 01 December 2006 Pages: 675 - 683
Analysis and influence of acetylene and propane gas during oxyfuel gas cutting of 1045 carbon steel Patricia Muñoz-EscalonaMaria Carolina PayaresRonald Diaz OriginalPaper 01 December 2006 Pages: 684 - 692
Microstructure of a nitrided steel previously decarburized I. CalliariM. DabalàE. Gianotti OriginalPaper 01 December 2006 Pages: 693 - 698
Comparative characteristic and erosion behavior of NiCr coatings deposited by various high-velocity oxyfuel spray processes Hazoor Singh SidhuButa Singh SidhuS. Prakash OriginalPaper 01 December 2006 Pages: 699 - 704
Forming of magnesium alloys at 100 °C by hydrostatic extrusion J. SwiostekJ. GökenK. U. Kainer OriginalPaper 01 December 2006 Pages: 705 - 711
Flexural strength distribution of 3D SiC/SiC composite Shoujun WuLaifei ChengYongdong Xu OriginalPaper 01 December 2006 Pages: 712 - 716
Correlation between molten vanadium salts and the structural degradation of HK-type steel superheater tubes Frederico de Carvalho NunesLuiz Henrique de AlmeidaAndré Freitas Ribeiro OriginalPaper 01 December 2006 Pages: 717 - 721
Effect of bonding temperature on transient liquid phase bonding behavior of a Ni-based oxide dispersion-strengthened superalloy R. K. SahaT. I. Khan OriginalPaper 01 December 2006 Pages: 722 - 728
Cyclic oxidation behavior of some plasma-sprayed coatings in Na2SO4-60%V2O5 environment Harpreet SinghSatya PrakashD. M. Phase OriginalPaper 01 December 2006 Pages: 729 - 741
Effect of corrosion on mass loss, and high and low cycle fatigue of reinforcing steel Ch. Alk ApostolopoulosD. Michalopoulos OriginalPaper 01 December 2006 Pages: 742 - 749
Postmortem raman spectroscopy explaining friction and wear behavior of sintered polyimide at high temperature P. SamynP. De BaetsF. Verpoort OriginalPaper 01 December 2006 Pages: 750 - 757
Microstructure and corrosion behavior of shielded metal arc-welded dissimilar joints comprising duplex stainless steel and low alloy steel P. Bala SrinivasanV. MuthupandiW. Dietzel OriginalPaper 01 December 2006 Pages: 758 - 764