Mechanical Properties of White Etching Areas in Carburized Bearing Steel Using Spherical Nanoindentation Jonathan F. W. LeungVikram BedekarRichard W. Neu Communication 23 August 2019 Pages: 4949 - 4954
In Situ Observation of Martensite Lath Growth Behaviors in the Coarse Grained Heat-Affected Zone of 1.25Cr-0.5Mo Heat-Resistant Steel During Simulated Welding Yang ShenCong Wang Communication 22 August 2019 Pages: 4955 - 4960
Dependency of Natural Aging on the Ferritfoe Grain Size in Dual-Phase Steel Mehran ZamaniHamed MirzadehHamid M. Ghasemi Communication 22 August 2019 Pages: 4961 - 4964
Observation of a[100] Dislocations in the γ′ Phase in a [011]-Oriented Nickel-Base Single Crystal Superalloy During High Temperature Creep Yifei LiLi WangLanghong Lou Communication 26 August 2019 Pages: 4965 - 4969
A General Strategy for Enhancing 3D Printability of High Laser Reflectivity Pure Aluminum Powder Kang GengYafeng YangQingshan Zhu Communication 30 August 2019 Pages: 4970 - 4976
In Situ Observation of Bainite Transformation and Simultaneous Carbon Enrichment in Austenite in Low-Alloyed TRIP Steel Using Time-of-Flight Neutron Diffraction Techniques Yusuke OnukiTakashi HiranoToshiro Tomida OriginalPaper 22 August 2019 Pages: 4977 - 4986
Significance of Partial Substitution of Carbon by Nitrogen on Strengthening and Toughening Mechanisms of High Nitrogen Fe-15Cr-1Mo-C-N Martensitic Stainless Steels Hao FengHua-Bing LiZhi-Gang Chen OriginalPaper 19 August 2019 Pages: 4987 - 4999
Confirmation of Dynamically Recrystallized Grains in Hexagonal Zirconium through Local Internal Friction Measurements K. S. ThoolK. V. Mani KrishnaI. Samajdar OriginalPaper 22 August 2019 Pages: 5000 - 5014
Effect of Precipitation Control on Strength and Impact Toughness in Advanced Pressure Vessel Steel Hyun Je SungSung-Joon Kim OriginalPaper 22 August 2019 Pages: 5015 - 5022
Quantitative Analysis of Load–Displacement Curves in Erichsen Cupping Test for Low Carbon Steel Sheet Naoya KamikawaHaruka Morino OriginalPaper 22 August 2019 Pages: 5023 - 5037
Microstructural Origin of Residual Stress Relief in Aluminum Arijit LodhTawqeer Nasir TakIndradev Samajdar OriginalPaper 26 August 2019 Pages: 5038 - 5055
The Effects of Grain Size and Strain Amplitude on Persistent Slip Band Formation and Fatigue Crack Initiation Chun-Yu OuC. Richard Liu OriginalPaper 22 August 2019 Pages: 5056 - 5065
The Anisotropy of Serrated Flow Behavior of Al-Cu-Li (AA2198) Alloy Niraj NayanS. V. S. Narayana MurtyI. Samajdar OriginalPaper 09 September 2019 Pages: 5066 - 5078
Evolution of Substructure of a Non-equiatomic FeMnCrCo High Entropy Alloy Deformed at Ambient Temperature A. K. ChandanS. TripathyS. G. Chowdhury OriginalPaper 29 August 2019 Pages: 5079 - 5090
Hydrogen Desorption Spectra from Excess Vacancy-Type Defects Enhanced by Hydrogen in Tempered Martensitic Steel Showing Quasi-cleavage Fracture Kei SaitoTetsuya HiradeKenichi Takai OriginalPaper 11 September 2019 Pages: 5091 - 5102
Estimation of the Temperature in the Stirred Zone and Cooling Rate of Friction Stir Welding of EH46 Steel from TiN Precipitates Montadhar Al-moussawiAlan J. SmithStephen Cater OriginalPaper 30 August 2019 Pages: 5103 - 5116
Microstructural Evolution and Mechanical Properties of Nickel-Base Superalloy Brazed Joints Using a MPCA Filler Minrui GaoBenjamin SchneidermanZhenzhen Yu OriginalPaper 22 August 2019 Pages: 5117 - 5127
Liquid Metal Embrittlement Cracking During Resistance Spot Welding of Galvanized Q&P980 Steel Zhanxiang LingTing ChenMing Lei OriginalPaper 30 August 2019 Pages: 5128 - 5142
Interfacial Segregation of Alloying Elements During Dissimilar Ultrasonic Welding of AA6111 Aluminum and Ti6Al4V Titanium Chaoqun ZhangJoseph D. RobsonPhilip B. Prangnell OriginalPaper Open access 03 September 2019 Pages: 5143 - 5152
Multi-Length Scale Characterization of Microstructure Evolution and Its Consequence on Mechanical Properties in Dissimilar Friction Stir Welding of Titanium to Aluminum Amlan KarSatyam SuwasSatish V. Kailas OriginalPaper 26 August 2019 Pages: 5153 - 5173
Analytical Description of the Influence of the Welding Parameters on the Hot Cracking Susceptibility of Laser Beam Welds in Aluminum Alloys Christian HagenlocherDaniel WellerThomas Graf OriginalPaper 28 August 2019 Pages: 5174 - 5180
Microstructure and Mechanical Properties of Vacuum Brazed NbSS/Nb5Si3 Composite Joints Using Ni-Based Filler Alloys X. Y. RenH. P. XiongY. Y. Cheng OriginalPaper 28 August 2019 Pages: 5181 - 5190
Influence of In Situ Thermal Processing Strategies on the Weldability of Martensitic Stainless Steel Resistance Spot Welds: Effect of Second Pulse Current on the Weld Microstructure and Mechanical Properties Hamidreza AghajaniMajid Pouranvari OriginalPaper 13 September 2019 Pages: 5191 - 5209
Marangoni-Convection-Driven Bubble Behavior and Microstructural Evolution of Sn-3.5Ag/Sn-17Bi-0.5Cu (Wt Pct) Alloy Solidified on Cu Substrate Under Space Microgravity Condition Zhangfu YuanRongyue WangXiangtao Yu OriginalPaper 22 August 2019 Pages: 5210 - 5220
On the Growth Dynamics of Nearly-Locked Grain in the Three-Phase In-Bi-Sn Eutectic System Samira MohagheghiMelis Şerefoğlu OriginalPaper 28 August 2019 Pages: 5221 - 5233
On the Deformation of Dendrites During Directional Solidification of a Nickel-Based Superalloy J. W. AvesonG. ReinhartH. J. Stone OriginalPaper Open access 26 August 2019 Pages: 5234 - 5241
The Role of Grain Refiner in the Nucleation of AlFeSi Intermetallic Phases During Solidification of a 6xxx Aluminum Alloy A. LuiP. S. GrantK. A. Q. O’Reilly OriginalPaper Open access 16 September 2019 Pages: 5242 - 5252
The Role of Ultrasonically Induced Acoustic Streaming in Developing Fine Equiaxed Grains During the Solidification of an Al-2 Pct Cu Alloy Gui WangQiang WangDavid H. StJohn OriginalPaper 11 September 2019 Pages: 5253 - 5263
Enhancing Thermal Stability of Binary Al-Mg Alloys by Tailoring Grain Orientations Using a High Solute Mg Content Min ZhaXiang-Tao MengQi-Chuan Jiang OriginalPaper 28 August 2019 Pages: 5264 - 5270
A Simplified Hot-Tearing Criterion for Shape Castings Based on Temperature-Field Simulation Ke WangPenghuai FuWenjiang Ding OriginalPaper 22 August 2019 Pages: 5271 - 5280
An Investigation of Tertiary γ′ Precipitation in a Powder-Metallurgy, γ-γ′ Nickel-Base Superalloy S. L. SemiatinN. C. LevkulichJ. S. Tiley OriginalPaper 19 August 2019 Pages: 5281 - 5296
Effects of Strain Rate and Annealing Temperature on the Evolution of Microstructure and Texture in Pure Niobium T. W. XuS. S. ZhangY. Wan OriginalPaper 22 August 2019 Pages: 5297 - 5313
The Investigation on Flow Behavior of Powder Metallurgy Ti-10V-2Fe-3Al Alloy Using the Prasad Stability Criterion Krystian ZygułaMarek WojtaszekUlrich Prahl OriginalPaper Open access 09 September 2019 Pages: 5314 - 5323
The Effect of Die Bearing Geometry on Surface Recrystallization During Extrusion of an Al-Mg-Si-Mn Alloy Y. MahmoodkhaniJ. ChenN. C. Parson OriginalPaper Open access 30 August 2019 Pages: 5324 - 5335
Wire Electric Discharge Machining of P91 Steel: Microstructure and Thermal Modeling Studies S. BhattacharyaA. MishraG. K. Dey OriginalPaper 16 September 2019 Pages: 5336 - 5355
Study of Dry Sliding Wear Behavior of Hot-Rolled and Mushy-State Rolled Al-4.5Cu-5TiB2 In-Situ Composite with Analysis of Work Hardening and Subsurface Microstructure-Microtexture Evolution Using EBSD Monalisa MandalRahul Mitra OriginalPaper 19 August 2019 Pages: 5356 - 5372
Effect of Tool Shoulder Diameter on the Surface Hardness of Aluminum-Molybdenum Surface Composites Developed by Single and Double Groove Friction Stir Processing V. P. MaheshAmit Arora OriginalPaper 22 August 2019 Pages: 5373 - 5383
Microstructure, Wetting, and Tensile Behaviors of Sn-Ag Alloy Reinforced with Copper-Coated Carbon Nanofibers Produced by the Melting and Casting Route Ashutosh SharmaAshok K. SrivastavaByungmin Ahn OriginalPaper 03 September 2019 Pages: 5384 - 5394
Wear Performance Analysis of Aluminum Matrix Composites and Optimization of Process Parameters Using Statistical Techniques Amir Hussain IdrisiAbdel-Hamid Ismail Mourad OriginalPaper 13 September 2019 Pages: 5395 - 5409
Influence of Cr Content on the Microstructure and Electrochemical Corrosion in Plasma Cladding Ni-Cr Coatings Wenya ZhangCanming WangChunzhi Zhang OriginalPaper 13 September 2019 Pages: 5410 - 5420
Using Variant Selection to Facilitate Accurate Fitting of γ″ Peaks in Neutron Diffraction R. Y. ZhangH. L. QinH. B. Dong OriginalPaper Open access 28 August 2019 Pages: 5421 - 5432
Microstructure and Texture Evolution During Thermomechanical Processing of Al0.25CoCrFeNi High-Entropy Alloy Leandro A. SantosSaransh SinghAnthony D. Rollett OriginalPaper 23 August 2019 Pages: 5433 - 5444
Oxidation Behavior Across Composition Space Relevant to Co-based γ/γ′ Alloys Colin A. StewartAkane SuzukiCarlos G. Levi OriginalPaper 22 August 2019 Pages: 5445 - 5458
Effect of Phosphorus on the Phase Stability of a High Refractory Content Powder-Processed Ni‐Base Superalloy Linhan LiGeorge KimSammy Tin OriginalPaper 22 August 2019 Pages: 5459 - 5475
Study on the Influence of Prior Cold Work on Precipitation Behavior of 304HCu Stainless Steel During Isothermal Aging R. ManojkumarS. MahadevanM. N. Singh OriginalPaper 09 September 2019 Pages: 5476 - 5482
Optical and Microstructural Origins of Thermomechanical Streaking Defects in Hot Extruded AA6060 S. BabaniarisA. G. BeerM. R. Barnett OriginalPaper 26 August 2019 Pages: 5483 - 5493
Compressive and Energy Absorption Behavior of Multilayered Foam Filled Tubes M. SalehiS. M. H. MirbagheriM. Arabkohi OriginalPaper 13 September 2019 Pages: 5494 - 5509
Pulse Plating of Ni-W-B Coating and Study of Its Corrosion and Wear Resistance Mir Ghasem HosseiniSomayeh AhmadiyehShahin Khameneh-asl OriginalPaper 13 September 2019 Pages: 5510 - 5524
The Positive Effect of Hydrogen Alloying on the Phase Tailoring and Mechanical Properties of Sintered Ti-13Nb SMAs Z. XuB. YuanY. Gao OriginalPaper 27 August 2019 Pages: 5525 - 5532
Physicomechanical, Phase Composition, and In Vitro Study of High-Temperature Sintered ZTA/HA Composites S. M. NagaM. SayedH. F. El-Maghraby OriginalPaper 23 August 2019 Pages: 5533 - 5541