1. A most important project of the third, decisive year the country's most powerful 3600 mill of the Azovstal' Plant has produced the first sheet

   • Ya Brodskii

   OriginalPaper Pages: 537 - 545

2. Reducing roll up of fuel in pelletizing prior to sintering

   • G. V. Korshikov
   • M. A. Khaikov
   • E. V. Nevmerzhitskii

   Cast Iron Pages: 546 - 549

3. Blast-furnace smelting of iron-ore pellets

   • L. Ya Gavrilyuk

   Cast Iron Pages: 550 - 553

4. Life of blast-furnace charging equipment when smelting pellets

   • V. P. Bratchenko
   • N. M. Kryukov
   • V. I. Vier

   Cast Iron Pages: 554 - 556

5. Life of hot blast valves

   • L. B. Zil'berman

   Cast Iron Pages: 557 - 559

6. Casting killed steel under a perlite-graphite mixture

   • A. F. Dolgopolov
   • A. A. Tkachenko
   • V. F. Baiduzh

   Cast Iron Pages: 560 - 562

7. Abrasive cutting of consumable electrodes

   • I. Ya Zhabin
   • L. K. Kosyrev
   • B. T. Gorshkov

   Cast Iron Pages: 563 - 567

8. Behavior of the slag pockets of open-hearth furnaces during oxygen blowing of the bath

   • A. G. Notych

   Cast Iron Pages: 568 - 571

9. The complex treatment of open-hearth slags

   • A. E. Frolov
   • M. I. Panfilov
   • A. I. Krasil'nikov

   Cast Iron Pages: 572 - 574

10. Device for cutting runners

    • V. K. Ovcharenko
    • V. P. Chebotarev

    Cast Iron Pages: 575 - 575

11. Experience of operating a modern slabbing mill

    • A. E. Pratusevich
    • M. M. Maizholov

    Rolled Products Pages: 576 - 578

12. Improvement of the rolling of special sections on the 550 mill

    • P. I. Polukhin
    • V. T. Zhadan
    • Yu. I. Ivankin

    Rolled Products Pages: 579 - 582

13. Increase of the service life of individual components of the equipment of the pilger rolling mill

    • Yu. V. Poyurovskii
    • I. G. getiya
    • V. V. Ermakov

    Rolled Products Pages: 583 - 584

14. Computer for measuring the consumption of electrical energy

    • G. N. Kharchenko
    • O. U. Fleishman
    • V. P. Fedorov

    Rolled Products Pages: 585 - 586

15. Increase of the reliability of circular saws

    • I. F. Chirkov
    • V. P. Lukin

    Rolled Products Pages: 587 - 588

16. Rolling of the lock rings for automobile wheels

    • B. M. Ilyukovich
    • S. E. Merkur'ev

    Rolled Products Pages: 589 - 589

17. Three-phase contactless power circuit breaker employing symmetric thyristors

    • O. G. Vilkul
    • V. I. Grandt
    • M. S. Yatsevich

    Rolled Products Pages: 590 - 591

18. Introduction of repeaters on the finishing stands of light-section mills

    • Yu. P. Kovtanyuk
    • A. V. Kuzminskii
    • Yu. I. Ivankin

    Rolled Products Pages: 592 - 592

19. The choice of operating parameters for Venturi tubes in design and operation of flue gas purifiers

    • É. M. Kunina
    • G. R. Ostanovskii
    • M. M. Cherepinskii

    Industrial Safety Pages: 593 - 594

20. New books on the rolling industry

    Industrial Safety Pages: 595 - 595

21. At optimal speeds with minimum deviations (from the working experience of the brigade of blooming mill millmen)

    • A. Pelenov
    • P. Goncharov
    • V. Dombrovskii

    Air to Schools of Communist Labor Pages: 596 - 597

22. Roads of friendship

    • I. Chirkov

    Air to Schools of Communist Labor Pages: 598 - 599

23. The plant's most valuable possession

    • M. M. Zaslavskii

    Air to Schools of Communist Labor Pages: 600 - 601

24. Peter Gerasimovich Glazkov, engineer

    • M. Kamenskii

    Air to Schools of Communist Labor Pages: 602 - 604

25. A milionaire three times over

    • O. Semko

    Air to Schools of Communist Labor Pages: 605 - 606

26. Cesium

    • S. I. Venetskii

    Air to Schools of Communist Labor Pages: 607 - 609