1. Unabashed attention to industrial hygiene

   • M. M. Zin'kovskii

   BriefCommunication Pages: 613 - 615

2. Effect of the coarseness of fuel on the quality of sinter from finely crushed concentrate

   • G. M. Efimenko
   • V. G. Vlasov
   • G. V. Tsukanov

   Pig Iron Pages: 616 - 618

3. Monitoring of the charge surface profile along the blast furnace top radius

   • V. A. Smolyak
   • V. I. Vasilenko
   • N. T. Evseeva

   Pig Iron Pages: 619 - 622

4. Elastically suspended drum mixers and granulators

   • L. R. Migutskii
   • A. L. Matov

   Pig Iron Pages: 623 - 626

5. Mechanized delivery of samples in a sintering plant

   • L. M. Arist
   • A. N. Gorodetskii
   • A. M. Robustov

   Pig Iron Pages: 627 - 629

6. Burnt iron ore pellets in open-hearth furnaces

   • G. S. Kolganov
   • F. I. Bashlii
   • V. F. Bazarnyi

   Steel Pages: 630 - 633

7. Continuous casting of pipe steel with the use of exothermal mixtures

   • O. V. Martynov
   • S. M. Gorlov
   • A. I. Mazun

   Steel Pages: 634 - 637

8. Economic effect of continuous casting (submerged) of shipbuilding steels

   • V. S. Rutes
   • V. I. Askol'dov
   • N. A. Oskolkov

   Steel Pages: 638 - 639

9. Casting of tube steel in continuous steel pouring units

   • N. G. Gladyshev
   • V. P. Druzhinin
   • S. M. Gorlov

   Steel Pages: 640 - 643

10. Increasing the power of arc furnace transformers

    • D. K. Kuznetsov
    • N. A. Tulin
    • I. Yu. Zinurov

    Steel Pages: 644 - 645

11. Lack of uniformity in the metal across the width of the bath in an open-hearth furnace

    • G. A. Rudakov

    Steel Pages: 646 - 647

12. Rolling flat steel on the 250 light-section mill

    • A. A. Kugushin
    • A. I. Prokop'ev
    • V. S. Tseluikov

    Rolled Products Pages: 648 - 649

13. Powder-compacted wire used for hardfacing blooming mill rolls

    • S. A. Lyadov
    • Yu. P. Dolgoker
    • I. N. Aksenov

    Rolled Products Pages: 650 - 652

14. High-chromium iron section rolls

    • V. T. Zhadan
    • Yu. E. Kular
    • U. S. Govor

    Rolled Products Pages: 653 - 656

15. Redesign of the reeling mill for the 400 tube rolling line

    • A. F. Krisanov

    Rolled Products Pages: 657 - 659

16. Modernization of the attachment of the rolling tool of piercing and reeling mills

    • A. F. Krisanov
    • V. Kh. Kurilenko

    Rolled Products Pages: 660 - 661

17. Operation of a sectional furnace for high-speed heating of tubes before sizing and reducing

    • P. E. Osipenko
    • A. S. Rozen
    • A. K. Zinchenko

    In the Rolling Mills of the Country Pages: 662 - 663

18. Improvement of the attachment of the mandrel for drawing tubes

    • A. B. Lamin
    • V. V. Donets
    • B. S. Mailis

    In the Rolling Mills of the Country Pages: 664 - 665

19. List planning in mechanical repair shops (for purposes of discussion)

    • A. I. Gaidarenko
    • G. M. Borodulin

    In the Rolling Mills of the Country Pages: 666 - 669

20. Important untapped reserves for increasing the productivity of labor

    • V. Karlov

    In the Rolling Mills of the Country Pages: 670 - 672

21. Grum-Grzhimailo in the Urals

    • N. A. Mezenin

    In the Rolling Mills of the Country Pages: 673 - 676

22. The control board and desk of a converter

    • A. I. Luk'yanchikov
    • V. K. Borovikov
    • F. P. Levchenko

    In the Rolling Mills of the Country Pages: 677 - 678