Present state and prospects for improvement in high-pressure apparatus and pipelines V. G. Usenko OriginalPaper Pages: 654 - 656
Production of roulonated (rolled) high-pressure equipment at the 50th-Anniversary-of-the-USSR Uralkhimmash plant and attempts of further increasing its quality and efficiency V. M. Makarov Announcement Pages: 656 - 658
Trends in the development of the production of high-pressure vessels in rolled design E. R. KhismatulinM. M. Shel'V. I. Livshits OriginalPaper Pages: 658 - 659
Experience from the construction and start-up of the production of large high-pressure apparatus for production process lines for the synthesis of ammonia with a capacity of 1360 tons/day V. V. IvantsovB. I. Bondarenko OriginalPaper Pages: 660 - 662
Construction of spiral-rolled high-pressure vessels V. M. MakarovM. M. Shel' OriginalPaper Pages: 662 - 667
Investigation of the stress-strain condition of a multilayer rolled wall L. A. Il'inN. A. LobkovaN. P. Starikov OriginalPaper Pages: 668 - 671
Study of the causes for the failure of a high-pressure vessel O. M. Kop'evaV. N. Grigor'evD. G. Malova OriginalPaper Pages: 672 - 674
Stress state of tubular grids of high-pressure vessels V. G. TatarinovA. G. Berman OriginalPaper Pages: 674 - 678
Load-bearing ability of thick-walled pipelines under the joint action of pressure and a bending moment B. P. SergievB. M. Gusev OriginalPaper Pages: 678 - 681
Investigation and development of norms for the construction of seals for high-pressure vessels V. I. LivshitsV. K. Pogodin OriginalPaper Pages: 681 - 682
Calculation of the tightening regimes of fastening pegs with hydraulic jacks V. D. ProdanV. P. Viryukin OriginalPaper Pages: 683 - 684
Determination of the average tightness of layers in the manufacture of multilayer vessels P. G. PimshteinE. G. Borsuk OriginalPaper Pages: 684 - 686
Sealing properties of electrolytic coatings A. I. PromptovO. P. LivshitsG. D. Gridin OriginalPaper Pages: 686 - 688
Comprehensive flaw detection in high-pressure vessels V. I. ÉtingovM. M. Shel'S. M. Zholobov OriginalPaper Pages: 688 - 691
A method for reducing the residual stresses in peripheral welded joints in high-pressure vessels V. I. NovikovM. A. NetrebskiiV. A. Nekhotyashchii OriginalPaper Pages: 691 - 693
Mechanical properties of rolled steels with an ultimate strength of 60–70 kgf/mm2 and their welded joints E. R. KhismatulinV. D. MolchanovaA. G. Kolmakov OriginalPaper Pages: 693 - 695
NDTs-25 continuous centrifugal blender S. A. RevenkoZ. A. SorokinaI. I. Bagrintsev New Machinery and Equipment Pages: 701 - 702
Development and introduction of three-cutter drilling bits for medium-hardness rocks P. I. SopinA. S. YudinV. I. Pozdnyakov New Machinery and Equipment Pages: 702 - 704
Determination of the movement time of the sealing element in dry membrane valves for acetylene at medium pressures V. V. NasonovA. Yu. Potapov Design and Construction of Machinery and Equipment Pages: 707 - 711
Selecting the geometric parameters of rupture disks in safety devices N. N. Malakhov Design and Construction of Machinery and Equipment Pages: 711 - 713
Scheme for the automatic control of the regeneration of granular filters by pulsed reverse blowing N. A. SidorenkoV. Ya. BashkardinK. A. Vaitanik Design and Construction of Machinery and Equipment Pages: 714 - 714
New construction materials for manufacturing screens of sorting equipment R. M. MasalimovYu. G. PlyusninA. O. Toporkov New Materials and Corrosion Control Pages: 715 - 718
Stability of metallic coatings in thermal cycling E. I. StorchaiM. V. Kuznetsova New Materials and Corrosion Control Pages: 718 - 720
High production efficiency is the basis of scientific organization of labor and improvement of its effectiveness V. F. LitvitskiiV. P. Prokhorov Organization and Economics of Production Pages: 721 - 724
Abstracts of articles deposited at the Central Scientific-Research Institute for Scientific and Technical Information for Chemical and Petroleum Machinery Construction Information Pages: 727 - 728