Submersible electric pump unit for lifting seawater B. V. Khimach New Machines and Equipment Pages: 761 - 764
Units for production of cycle inner tube and casing stock A. G. PosternakN. A. EfremovaV. P. Opanasyuk New Machines and Equipment Pages: 765 - 768
Stress-deformation state of a three-layer elliptical bottom I. K. GlushkoV. I. VoroninF. I. Selitskii Construction and Design of Machines and Equipment Pages: 769 - 772
Stresses of the crankshafts of opposing compressors on an M10 base with cantilevered electric motors Yu. I. Smirnov Construction and Design of Machines and Equipment Pages: 772 - 776
Approximate method for calculating the shafts of mixers in multimixer apparatus I. N. KarasevV. A. ZaitsevA. N. Koldashov Construction and Design of Machines and Equipment Pages: 776 - 778
Start-up frictional forces in end packings B. M. KudryavtsevaG. E. Lazarev Construction and Design of Machines and Equipment Pages: 778 - 780
Pulsations in pressure drop in apparatus with a nonuniform fluidized bed N. A. ShakhovaO. G. Shapovalova Investigation and Calculation of Thermophysical Processes Pages: 781 - 782
Distribution of the velocities of the medium along the channels of a graphite-block heat-transfer apparatus V. G. OrlovG. S. Orlova Investigation and Calculation of Thermophysical Processes Pages: 783 - 786
Hydrodynamics of three-dimensional liquid films in a trans verse-cocurrent flow of gas N. I. SvitkaN. I. Gel'perinA. A. Chivyaga Investigation and Calculation of Thermophysical Processes Pages: 786 - 789
Procedure for calculating the cooling of cryogenic liquids under a regime of boiling and surface evaporation A. M. DomashenkoV. P. KachuraS. N. Zholus Investigation and Calculation of Thermophysical Processes Pages: 789 - 793
Corrosion damage of tanks transporting refined sulfuric acid G. P. GerasimenkoO. I. SteklovA. D. Konyukov New Materials and Corrosion Control Pages: 794 - 796
Local failure of 12Kh18N10T steel in nitric acid containing various chlorides G. A. Shul'gatV. S. PakhomovI. Ya. Klinov New Materials and Corrosion Control Pages: 797 - 799
New materials for arc welding of nickel and results of their introduction in the chemical-engineering industry G. S. Kuz'minT. F. MochalovaL. N. Bitinskaya Equipment-Manufacturing Technology Pages: 800 - 801
Experimental design in investigating the technology of rolling thick-walled elliptical heads K. N. BogoyavlenskiiI. V. Berezin Equipment-Manufacturing Technology Pages: 802 - 807
Machining the blanks for high-strength iron rotors of screw compressors B. N. KononenkoN. P. Kudryavskii Equipment-Manufacturing Technology Pages: 807 - 808
The effect of rapid heating on the properties of ShKh15 steel in assembling rolling bearing units G. Ya. AndreevV. I. KushakovI. E. Chernikova Equipment-Manufacturing Technology Pages: 809 - 812
Development and introduction of internal plant price lists for tools Yu. G. GlazovV. Ya. NekhaichikI. G. Nastasyuk Organization and Economics of Production Pages: 813 - 814
Improvements in the installation of stationary compressors V. A. ChepelovL. M. GidonD. S. Kosorukov Organization and Economics of Production Pages: 814 - 816
Theoretical and experimental study of the lifetime of direct-flow valve membranes of opposite compressors L. A. SosnovskiiI. P. Chigrina Quality, Reliability, and Lifetime Pages: 817 - 823
Efficiency of the flat seal of exhaust valves A. Z. VolynchikK. A. KozlovS. A. Khmelev Quality, Reliability, and Lifetime Pages: 823 - 824
Isothermal hardening of cyclinders with the use of blowing with argon V. V. Dolzhnikov Exchange of Experience Pages: 825 - 826
Single-point tools for machining ceramic materials K. P. Belous Exchange of Experience Pages: 826 - 827
Disk vacuum filter with a thickening device O. L. BrukV. L. RadushkevichM. G. Bogomol'nyi Information Pages: 832 - 835
A unit for heat treating cylindrical parts with high-frequency currents B. L. LedyaevN. I. ShumovskiiV. N. Strotskii Information Pages: 836 - 838
The use of polystyrene impressions for investigating the microstructures of metals V. D. MolchanovaA. P. TuritsinaS. A. Koval'chuk Information Pages: 838 - 839
Metal-ceramic electric heaters for heating polymer equipment B. L. Ositinskii Information Pages: 839 - 841