Abstract
Analysis of die failure plays an important role in the prediction and prevention of die failure, and subsequently in improving economics of any metal-forming process. Industrial experience has shown that fracture is the most common mode of failure in the case of hot aluminum extrusion dies. The purpose of the present work is to implement fatigue damage models in a Finite Element code for identification of critical process parameters and die design features in the case of fatigue being the dominating failure mode. For the maximum number of billets extruded by the die before fatigue crack initiation (fatigue life cycles in extrusion), Morrow’s stress- and strain-life damage models are implemented for axisymmetric flat extrusion die. With the help of finite element software ABAQUS, extrusion process is simulated and dynamic stress and strain values were obtained by first identifying the potential fatigue location in the die. The evaluation of applicability of the damage models is done for specific hot extrusion die made of H13 steels with Al-6063 as billet material. By considering temperature and strain rate as process parameters and bearing length and fillet radius of the die as geometric features, different simulation runs are performed to investigate the effect of process and design features on the useful die life. Morrow’s stress life model shows a good correspondence between computed and actual failure of dies. By establishing correlations of die life with process and design parameters under different conditions, it was shown that the present investigation is a useful guideline at die design and extrusion process stages.
Similar content being viewed by others
References
Fu, M.W., Yong, M.S., Tong, K.K., Muramatsua, T.: Methodology for evaluation of metal forming system design and performance via CAE simulation. Int. J. Prod. Res. 44(6), 1075–1092 (2006)
Arif, A.F.M., Sheikh, A.K., Qamar, S.Z.: A study of die failure mechanisms in aluminum extrusion. J. Mater. Process. Technol. 134, 318–328 (2003)
Arif, A.F.M., Akhtar, S.S., Sheikh, A.K.: Critical die failure types for hot aluminum extrusion. In: Proceedings of 4th International Conference and Exhibition on Design and Production of Machines and Dies/Molds, Cesme, Turkey, pp. 74–76 (2007)
Tong, K.K., Yong, M.S., Fu, M.W., Muramatsu, T., Goh, C.S., Zhang, S.X.: CAE enabled methodology for die fatigue life analysis and improvement. Int. J. Prod. Res. 43(1), 131–146 (2005)
Falk, B., Engel, U., Geiger, M.: Estimation of tool life in bulk metal forming based on different failure concepts. J. Mater. Process. Technol. 80–81, 602–607 (1998)
Falk, B., Engel, U., Geiger, M.: Fundamental aspects for the evaluation of the fatigue behavior of cold forging tools. J. Mater. Process. Technol. 119(1–3), 158–164 (2001)
Saroosh, M.A., Lee, H.-C., Im, T.-T., Choi, S.-W., Lee, D.-L.: High cycle fatigue prediction of cold forging tools based on workpiece material property. J. Mater. Process. Technol. 191, 178–181 (2007)
Dowling, N.E.: Mechanical Behavior of Materials: Engineering Methods for Deformation, Fracture, and Fatigue, 2nd edn. Prentice-Hall, NJ (1999)
Wallace, J.F., Schwam, D.: Improved life of die casting dies of H13 steel by attaining improved mechanical properties and distortion control during heat treatment. Work done by Ohio State University and Case Western Reserve University for US Department of Energy, Washington DC (1995)
Lee, G.-A., Im, Y.-T.: Finite-element investigation of the wear and elastic deformation of dies in metal forming. J. Mater. Process. Technol. 89–90(119), 123–126 (1999)
Kuhn, H.A.: Atlas of Formability: Cast Aluminum 6063. National Center for Excellence in Metalworking Technology (NCEMT), PA (1991)
Engineeringtoolbox. http://www.engineeringtoolbox/docs (2007)
Wang, B.: The prediction of low cycle fatigue for die casting with FEM. Department of Mechanical and Aerospace Engineering Ottawa, Carleton Institute for Mechanical and Aerospace Engineering Carleton University, Ottawa, Canada (2000)
Saha, P.K.: Aluminum Extrusion Technology. ASM International, Materials Park (2000)
Acknowledgment
The authors acknowledge the support of King Fahd University of Petroleum and Minerals, Dhahran, Saudi Arabia, for this work through project # SB080002.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Akhtar, S.S., Arif, A.F.M. Fatigue Failure of Extrusion Dies: Effect of Process Parameters and Design Features on Die Life. J Fail. Anal. and Preven. 10, 38–49 (2010). https://doi.org/10.1007/s11668-009-9304-4
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11668-009-9304-4