Abstract
Cutting fluids are widely used in most machining processes to produce superior surface finish and suppress tool wear. Due to the increasing cost associated with the procurement and disposal, and environmental issues of traditional cutting fluids, researches have been carried out to search for biodegradable lubricants and alternative lubrication methods to reduce the dependency on traditional cutting fluids. The growing demand for biodegradable lubricants has opened an avenue for using vegetable oils as alternative lubricants for machining. This chapter discusses the effectiveness of various types of biodegradable oils as lubricants and additives, and alternative lubrication methods such as minimum quantity lubrication (MQL), mist lubrication and solid lubrication in machining processes.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Abou-El-Hossien KA, Yahya Z (2005) High-speed end-milling of AISI 304 stainless steels using new geometrically developed carbide inserts. J Mater Process Technol 162–163:596–602
Alves SM, Barros BS, Trajano MF, Ribeiro KSB, Moura E (2013) Tribological behaviour of vegetable oil-based lubricants with nanoparticles of oxides in boundary lubrication conditions. Tribol Int 65:28–36
Arndt M, Kacsich T (2003) Performance of new AlTiN coatings in dry and high speed cutting. Surf Coating Technol 163–164:674–680
Attanasio A, Gelfi M, Giardini C, Remino C (2006) Minimal quantity lubrication in turning: effect on tool wear. Wear 260:333–338
Belluco W, Chiffre LD (2004) Performance evaluation of vegetable-based oils in drilling austenitic stainless steel. J Mater Process Technol 148:171–176
Bhatia SM, Pandey PC, Shan HS (1978) Thermal cracking of carbide tools during intermittent cutting. Wear 51:201–211
Bhatia SM, Pandey PC, Shan HS (1980) The thermal condition of the tool cutting edge in intermittent cutting. Wear 61:21–30
Broniszewski K, Wozniak J, Czechowski K, Jaworska L, Olszyna A (2013) Al2O3-Mo cutting tools for machining hardened stainless steel. Wear 303:87–91
Chakraborty P, Asfour S, Cho A, Onar A, Lynn M (2008) Modelling tool wear progression by using mixed effects modelling technique when end milling AISI 4340 steel. J Mater Process Technol 205:190–202
Chou YK, Evans CJ (1997) Tool wear mechanism in continuous cutting of hardened tool steels. Wear 212:59–65
Costa ES, da Silva MB, Machado AR (2009) Burr produced on the drilling process as a function of tool wear and lubricant-coolant conditions. J Braz Soc Mech Sci Eng 31:57–63
Deng J, Song W, Zhang H, Yan P, Liu A (2011) Friction and wear behaviors of the carbide tools embedded with solid lubricants in sliding wear tests and in dry cutting processes. Wear 270:666–674
Deng J, Wu Z, Lian Y, Qi T, Cheng J (2012) Performance of carbide tools with textured rake-face filled with solid lubricants in dry cutting processes. Int J Refract Metal Hard Mater 30:164–172
Ding X, Liew WYH, Ngoi BKA, Gan JGK, Yeo SH (2002) Wear of CBN tools in ultra-precision machining of STAVAX. Tribol Lett 12:3–12
Dolinsek S, Sustarsic B, Kopac J (2001) Wear mechanism of cutting tool in high-speed cutting processes. Wear 250:349–356
Elkhabeery MM, Bailey JA (1984) Surface integrity in machining solution-treated and aged 2024-aluminium alloy, using natural and controlled contact length tools. part 1-unlubricated conditions. J Eng Mater Technol Trans ASME 106:152–160
Endrino JL, Fox-Rabinovich GS, Grey C (2006) Hard AlTiN, AlCrN PVD coatings for machining of austenite stainless steel. Surf Coat Technol 200:6840–6845
Erdemir A (2005) Review of engineered tribological interfaces for improved boundary lubrication. Tribol Int 38:249–256
Ezugwu EO, Bonney J (2005) Finish machining of nickel-base Inconel 718 alloy with coated carbide tool under conventional and high-pressure coolant supplies. Tribol Trans 48:76–81
Ezugwu EO, Olajire KA (2002) Evaluation of machining performance of martensitic stainless steel (JETHETE). Tribol Lett 12:183–187
Ghani JA, Choudhury IA, Masjuki HH (2004) Wear mechanism of TiN coated carbide and uncoated cermets tools at high cutting speed applications. J Mater Process Technol 153–154:1067–1073
Grill A (1993) Review of the tribology of diamond-like carbon. Wear 168:143–153
Gu J, Barber G, Tung S, Gu RJ (1999) Tool life and wear mechanism of uncoated and coated milling tool. Wear 225:273–284
Haque T, Morina A, Neville A (2010) Influence of friction modifier and antiwear additives on the tribological performance of a non-hydrogenated DLC coating. Surf Coat Technol 204:4001–4011
Itoigawa F, Childs THC, Nakamura T, Belluco W (2006) Effects and mechanisms in minimal quantity lubrication machining of an aluminum alloy. Wear 260:339–344
Kaminski J, Alvelid B (2000) Temperature reduction in the cutting zone in water-jet assisted turning. J Mater Process Technol 106:68–73
Kang MC, Kim KH, Shin SH, Jang SH, Park J, Kim C (2008) Effect of the minimum quantity lubrication in high-speed end-milling of AISI D2 cold-worked die Steel (62 HRC) by coated carbide tools. Surf Coat Technol 202:5621–5624
Kelly JF, Cotterell MG (2002) Minimal lubrication machining of aluminium alloys. J Mater Process Technol 120:327–334
Khan MMA, Mithu MAH, Dhar NR (2009) Effects of minimum quantity lubrication on turning ALSL 9310 alloy steel using vegetable oil-based cutting fluid. J Mater Process Technol 209:5573–5583
Kim SW, Lee DW, Kang MC, Kim JS (2001) Evaluation of machinability by cutting environments in high-speed milling of difficult-to-cut materials. J Mater Process Technol 111:256–260
Klocke F, Maßmann T, Gerschwiler K (2005) Combination of PVD tool coatings and biodegradable lubricants in metal forming and machining. Wear 259:1197–1206
Ko TJ, Kim HS, Chung BG (1999) Air-oil cooling method for turning of hardened material. Int J Adv Manuf Technol 15:470–477
Korkut I, Donertas MA (2007) The influence of feed rate and cutting speed on the cutting forces, surface roughness and tool-chip contact length during face milling. Mater Des 28:308–312
Krishna PV, Srikant RR, Rao DN (2010) Experimental investigation on the performance of nanoboric acid suspensions in SAE-40 and coconut oil during turning of AISI 1040 steel. Int J Mach Tools Manuf 50:911–916
Kubo T, Fujiwara S, Nanao H, Minami I, Mori S (2008) Boundary film formation from overbased calcium sulfonate additives during running in process of steel-DLC contact. Wear 265:461–467
Kumar AS, Durai AR, Sornakumar T (2006) The effect of tool wear on tool life of alumina-based ceramic cutting tools while machining hardened martensitic stainless steel. J Mater Process Technol 173:151–156
Liao YS, Lin HM (2007) Mechanism of minimum quantity lubrication in high-speed milling of hardened steel. Int J Mach Tools Manuf 47:1660–1666
Liao YS, Lin HM, Chen YC (2007) Feasibility study of the minimum quantity lubrication in high-speed end milling of NAK80 hardened steel by coated carbide tool. Int J Mach Tools Manuf 47:1667–1676
Liew WYH (2010) Low-speed milling of stainless steel with TiAlN single-layer and TiAlN/AlCrN nano-multilayer coated carbide tools under different lubrication conditions. Wear 269:617–631
Liew WYH, Ding X (2008) Wear progression of carbide tool in low-speed end milling of stainless steel. Wear 265:155–166
Liew WYH, Ngoi BKA, Lu YG (2003) Wear characteristics of PCBN tools in ultra-precision machining of stainless steel at low cutting speeds. Wear 254:265–277
Liew WYH, Lu YG, Ding X, Ngoi BKA, Yuan S (2004a) Performance of uncoated and coated carbide tools in the ultra-precision machining of stainless steel. Tribol Lett 17:851–857
Liew WYH, Yuan S, Ngoi BKA (2004b) Evaluation of machining performance of STAVAX with PCBN tools. Int J Adv Manuf Technol 23:11–19
Liew WYH, Dayou S, Dayou J, Siambun NJ, Ismail MAB (2014) The effectiveness of palm oil methyl ester as lubricant additive in milling and four-ball tests. Int J Surf Sci Eng 8:153–172
Lim CYH, Lim SC, Lee KS (1999) Wear of TiC-Carbide tools in dry turning. Wear 225–229:354–367
Liu N, Han C, Yang H, Xu Y, Shi M, Chao S, Xie F (2005) The milling performance of TiC-based cermet tools with TiN nanopowder addition against normalized medium carbon steel AISI 1045. Wear 258:1688–1695
Marinov V (1996) Experimental study on the abrasive wear in metal cutting. Wear 197:242–247
Minfray C, Fromentin G, Bierla A, Martin JM, Mogne TL (2014) The effect of an organic pentasulfide EP additive in turning and milling operations. Wear 317:129–140
Mistry KK, Morina A, Neville A (2011) A tribochemical evaluation of a WC-DLC coating in EP lubrication conditions. Wear 271:1739–1744
Naves VTG, Da Silva MB, Da Silva FJ (2013) Evaluation of the effect of application of cutting fluid at high pressure on tool wear during turning operation of AISI 316 austenitic stainless steel. Wear 302:1201–1208
Nordin M, Sundström R, Selinder TI, Hogmark S (2000) Wear and failure mechanisms of multilayered PVD TiN/TaN Tools when milling austenite stainless steel. Surf Coat Technol 133–134:240–256
Nouari M, Ginting A (2006) Wear characteristics and performance of multi-layer CVD-coated alloyed carbide tool in dry end milling of titanium alloy. Surf Coat Technol 200:5663–5676
Nouari M, Molinari A (2005) Experimental verification of a diffusion tool wear model using a 42CrMo4 steel with an uncoated cemented tungsten carbide at various cutting speeds. Wear 259:1151–1159
Ozcelik B, Kuram E, Demirbas E, Sik E (2011a) Optimization of surface roughness in drilling using vegetable-based cutting oils developed from sunflower oil. Ind Lubr Tribol 63:271–276
Ozcelik B, Kuram E, Cetin MH, Demirbas E (2011b) Experimental investigations of vegetable based cutting fluids with extreme pressure during cutting of AISI 304L. Tribol Int 44:1864–1871
Rahim EA, Sasahara H (2011) A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys. Tribol Int 44:309–317
Rahman M, Kumar AS, Choudhury MR (2000) Identification of effective zones for high pressure coolant in milling. CIRP Annals-Manufact Technol 49:47–52
Rahman M, Kumar AS, Salam MU (2002) Experimental evaluation on the effect of minimal quantities of lubricant in milling. Int J Mach Tools Manuf 42:539–547
Reddy NSK, Rao PV (2006) Experimental investigation to study the effect of solid lubricants on cutting forces and surface quality in end milling. Int J Mach Tools Manuf 46:189–198
Rowe GW (1981) Lubrication in metal cutting and grinding. Phil Mag 43:567–585
Shaw MC (1984) Metal cutting Principles. Oxford University Press, Oxford
Sharif S, Yusof NM, Idris MH, Ahmad ZB, Sudin I, Ripin A and Mat Zin, MAH (2009) Feasibility study of using vegetable oil as a cutting lubricant through the use of minimum quantity lubrication during machining, Research VOT No. 78055, Department of Manufacturing and Industrial Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia. http://eprints.utm.my/9729/1/78055.pdf
Shokrani A, Dhokia V, Newman ST (2012) Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids. Int J Mach Tools Manuf 57:83–101
Soderberg S, Hogmark S (1986) Wear mechanism and tool life of high speed steels related to microstructure. Wear 110:315–329
Sokovic M, Kopac J, Dobrzanki LA, Adamiak M (2004) Wear of PVD-coated solid carbide end mills in dry high-speed cutting. J Mater Process Technol 157–158:422–426
Stanford M, Lister PM, Kibble KA (2007) Investigation into the effect of cutting environment on tool life during the milling of a BS970-080A15 (En32b) low carbon steel. Wear 262:1496–1503
Su Y, He N, Li L, Li XL (2006) An experimental investigation of effects of cooling/lubrication conditions on tool wear in high-speed end milling of Ti–6Al–4V. Wear 261:760–766
Sun F, Li Z, Jiang D, Chen B (1998) Adhering wear mechanism of cemented carbide cutter in the intervallic cutting of stainless steel. Wear 214:79–82
Viera JM, Machado AR, Ezugwu EO (2001) Performance of cutting fluids during face milling of steels. J Mater Process Technol 116:244–251
Vivancos J, Luis CJ, Ortiz JA, Gonzalez HA (2005) Analysis of factors affecting the high-speed side milling of hardened die steels. J Mater Process Technol 162–163:696–701
Yallese MA, Chaoui K, Zeghib N, Boulanouar L, Rigal J (2009) Hard machining of hardened bearing steel using cubic boron nitride tool. J Mater Process Technol 209:1092–1104
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2015 The Author(s)
About this chapter
Cite this chapter
Liew Yun Hsien, W. (2015). Utilisation of Vegetable Oil, Solid Lubricant, Mist Lubrication, Minimum Quantity Lubrication (MQL) in Machining. In: Towards Green Lubrication in Machining. SpringerBriefs in Molecular Science(). Springer, Singapore. https://doi.org/10.1007/978-981-287-266-1_3
Download citation
DOI: https://doi.org/10.1007/978-981-287-266-1_3
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-287-265-4
Online ISBN: 978-981-287-266-1
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)