Advertisement

Multi-objective Optimization of Wire-Electric Discharge Machining Process Using Multi-objective Artificial Bee Colony Algorithm

  • P. J. PawarEmail author
  • M. Y. Khalkar
Conference paper
Part of the Advances in Intelligent Systems and Computing book series (AISC, volume 949)

Abstract

The selection of optimum process parameters in wire-electric discharge machining process such as peak current, wire tension, water pressure and duty factor plays a significant role for optimizing the process performance measure. In this paper, multi-objective optimization of wire-electric discharge machining (wire-EDM) is done using recently developed evolutionary optimization algorithm. The advanced algorithm developed for the purpose of optimization is known to be multi-objective artificial bee colony (MOABC) algorithm. The objectives considered in this work are material removal rate and wear ratio and subjected to the constraint of surface roughness.

Keywords

Wire-electric discharge machining Multi-objective artificial bee colony Material removal rate Surface roughness Wear ratio 

References

  1. 1.
    Scott, D., Boyina, S., Rajurkar, K.P.: Analysis and optimization of parameter combination in wire electrical discharge machining. Int. J. Prod. Res. 29, 2189–2207 (1991)CrossRefGoogle Scholar
  2. 2.
    Liao, Y.S., Huang, J.T., Su, H.C.: A study on the machining parameters optimization of wire electrical discharge machining. J. Mater. Process. Technol. 71, 487–493 (1997)CrossRefGoogle Scholar
  3. 3.
    Anand, K.N.: Development of process technology in wire-cut operation for improving machining quality. Total Qual. Manag. 7, 11–28 (1996)CrossRefGoogle Scholar
  4. 4.
    Hewidy, M.S., El-Taweel, T.A., El-Safty, M.F.: Modelling the machining parameters of wire electrical discharge machining of Inconel 601 using RSM. J. Mater. Process. Technol. 169, 328–336 (2005)CrossRefGoogle Scholar
  5. 5.
    Huang, J.T., Liao, Y.S.: Optimization of machining parameters of wire-EDM based on grey relational and statistical analyses. Int. J. Prod. Res. 41, 1707–1720 (2003)CrossRefGoogle Scholar
  6. 6.
    Kuriakose, S., Shunmugam, M.S.: Multi-objective optimization of wire-electro discharge machining process by Non-Dominated Sorting Genetic Algorithm. J. Mater. Process. Technol. 170, 133–141 (2005)CrossRefGoogle Scholar
  7. 7.
    Tosun, N., Cogun, C., Tosun, G.: A study on kerf and material removal rate in wire electrical discharge machining based on Taguchi method. J. Mater. Process. Technol. 152, 316–322 (2004)CrossRefGoogle Scholar
  8. 8.
    Tarng, Y.S., Ma, S.C., Chung, L.K.: Determination of optimal cutting parameters in wire electrical discharge machining. Int. J. Mach. Tools Manuf. 35, 1693–1701 (1995)CrossRefGoogle Scholar
  9. 9.
    Rao, R.V., Pawar, P.J.: Modeling and optimization of process parameters of wire electric discharge machining. J. Eng. Manuf. 223, 1431–1440 (2009)CrossRefGoogle Scholar
  10. 10.
    Pawar, P.J., Vidhate, U.S., Khalkar, M.Y.: Improving the quality characteristics of abrasive water jet machining of marble material using multi-objective artificial bee colony algorithm. J. Comput. Des. Eng. 5, 319–328 (2018)CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2020

Authors and Affiliations

  1. 1.K. K. Wagh Institute of Engineering Education and ResearchNashikIndia
  2. 2.Savitribai Phule Pune UniversityPuneIndia

Personalised recommendations