Abstract
Pneumatic servo control originated around World War II and has been widely used in astronavigation, aerocraft, and general industry. This chapter introduces the background, types, and characteristics of pneumatic servo system and describes the classification of pneumatic control valves and the flow characteristics of typical orifices.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Bibliography
Yin Y, Yu C, Lu T et al (2006) Study on characteristics of hydraulic accumulator and cylinder in aircraft under extreme temperature environment. Fluid Transm Control 5:10–13
Yin Y (2012) Electro-hydraulic servo control theory and application technology in extreme environment. Shanghai Science and Technology Press, Shanghai
Yin Y, Yu C, Lu T et al (2006) Study on air chamber pressure characteristics of aircraft hydraulic control system. Autopilot Infrared Technol 2:8–12
Yin Y (2001) Research on characteristics of electro-hydraulic servo valve of aircraft under extreme environment. National Natural Science Foundation funded project completion report (50775161), 20 Jan 2001
Yin Y (2008) Key basic theory research of aircraft steering gear system. Shanghai Pujiang Talent Plan (Class A) Summary Report (06PJ14092), 30 Sept 2008
Yin Y (2009) Theoretical research on integrated design of fuel cell vehicle super high pressure relief valve group. Shanghai Baiyulan Science and Technology Talent Fund Summary Report (2008B110), 28 May 2009
Yin Y (2010) Hydrogen booster above 45Â MPa pressure control and regulation technology research. National High Technology Research and Development Program (863 Program) project acceptance report (2007AA05Z119), 30 June 2010
Yin Y (2013) R&D and industrialization of key equipment for underground continuous wall and complex ground pile foundation construction. National Science and Technology Support Plan 2012 Annual Report
Yin Y (2013) Pneumatic asymmetry mechanism and high-speed pneumatic control of air-resistance gas volume. National Natural Science Foundation of China, 2012 Annual Report
Yin Y, Li S, Fu J et al (2009) Study on outlet temperature characteristics of vehicle pneumatic pressure reducing valve for hydrogen energy vehicles. Chin J Constr Mach
Yin Y, Shu Y, Wu J et al (2007) Study on pressure characteristics of asymmetric pneumatic servo valve with asymmetric load-bearing capacity. China Mech Eng 18(18):2167–2173
Yin Y, Li C, Yan M (2010) Characteristics of pneumatic servovalve with symmetrical unequal load and weight. J Shanghai Jiaotong Univ 44(4):500–505
Araki K, Yin Y, Ishino Y, Chen J (1997) Characteristics of asymmetric electropneumatic servo valve for pneumatic force control. In: Proceedings of hydraulics and pneumatics Society in Autumn, pp 72–74
Yin Y, Araki K, Ishino Y (1997) Characteristics of pneumatic force control system using a single acting cylinder. In: Proceedings of 15th symposium on fluid measurement and fluid dynamics and 12th symposium on fluid control, 45/48
Qu Y (1986) Pneumatic servo system. Shanghai Jiaotong University Press, Shanghai
Araki K, Yin Y (1998) High speed pneumatic force control using asymmetric servo valve and single acting cylinder for resistance spot welding amchine (1st report). J Jpn Hydraul Pneumatic Soc 29(1):9–15
Yin Y, Araki K (1999) High speed pneumatic force control using asymmetric servo valve and single acting cylinder for resistance spot welding amchine (2st report, experimental of asymmetric electropneumatic servo valve and hardware compensation of closed loop pressure control system). J Jpn Hydraul Pneumatic Soc 30(2):35–41
Araki K, Yin Y (1998) Research on pneumatic force control system for resistance spot welding machine. Mech Des Daily Ind Newspaper 42(2):72–77
Araki K (1971) Characteristics compensation of a force feedback pneumatic servo valve. J Autom Control Soc 7(4):72–81
Araki K (1979) Frequency characteristics of pneumatic spool valves and cylinders with uneven underlaps (1st to 4th report). Hydraul Pneumatics, 1979, 10(1):57–63, 10(6):361–367. 1981, 12(4):262–268, 269–276
Araki K (1989) An indirect measurement method of equivalent negative underlaps of spool valve. Hydraul Pneumatics 20(1):71–76
Araki K (1988) Frequency characteristics of pneumatic underlap valve controlled asymmetric cylinder. Hydraul Pneumatics 19(6):79–85
Araki K (1969) A study on high speed pneumatic servo mechanism. Institute of Industrial Science, The University of Tokyo
Araki K (1984) Frequency response of a pneumatic valve controlled cylinder with an uneven-underlap four-way valve part 2, part 4. J Fluid Control ASME 15(1):22–64
Japanese Society of Hydraulics and Pneumatics (1989) Handbook of hydraulics and pneumatics. Ohm Corporation, Tokyo
Shearer JL (1956) Study of pneumatic processes in the continuous control of motion with compressed air, Part 1 and Part 2. Trans. ASME 78:233–249
Shearer JL (1960) Resistance characteristics of control valve orifices. In: Proc Inst Mech Engrs London, Jan 1960
Blackburn JF, Reethof G, Shearer JL (1960) Fluid power control. Wiley & The Technology Press of M.I.T
Ezekiel FD, Shearer JL (1957) Pressure-flow characteristics of pneumatic valves. Trans ASME 79:1577–1590
Tuttle ER (1975) The cohesion term in van der Waals’s equation of state. Am J Phy 43(7):644–646
Cai M, Xiang C, Li C (2007) Evaluation system of energy consumption and energy loss analysis of pneumatic system J. Mech Eng 43(9):69–74
Yao X, Liang Z (2003) Study on the pressure characteristics of pneumatic jet tube valve servo. Tactical Missile Control Technol 3:39–43
Li B, Yang G (2003) Modeling and simulation of pneumatic artificial muscle system. Chin J Mech Eng 39(7):23–28
Jia G, Wang X, Chen Y et al (2003) Study on the energy control system of pneumatic vehicles. J Zhejiang Univ 37(6):715–718
Bai Y-H, Li X-N (2006) Study on double-loop control with friction torque compensation for swing cylinder position servo system. J Nanjing Univ Sci Technol 30(2):216–222
Tanaka H (1981) Control of servo cylinder position using proportional solenoid valve. Hydraul Pneumatics 12(4):57–61
Tanaka H (1987) Digital control and application on hydraulics and oneumatics. Modern Book Press, Tokyo
Kagawa T (1981) Consideration of heat transfer in dynamic characteristics of pneumatic resistance capacity system. Hydraul Pneumatics 12(3):209–212
Kagawa T, Ishii S (1992) Study on meter out control characteristics of pneumatic cylinder. Hydraul Pneumatics 23(1):93–100
Kagawa T (1990) Pneumatic thermal characteristics. Hydraul Pneumatics 28(7):15–18
Sanada K (1997) Modeling of transfer function of electrohydraulic servomechanism: consideration of error. In: Proceedings of hydraulics and pneumatics Society in Autumn, pp 102–104
Kawahashi M, Arakawa M (1995) Analysis of sound velocity distribution in Stokes layer in tube column vibration. J Jpn Soc Mech Eng (B) 61(5):158–165
Kohei A (1963) Investigation on basic operation characteristics of compressed air circuit of resistance welding machine. Japan Welding Society
Noritsugu T (1990) Force control of pneumatic servo system using adaptive control. J Autom Control Soc 26(2):196–203
Noritsugu T (1988) Improvement of positioning control by air cylinder. Power Des 26(3):26–31
Noritsugu T, Takaiwa M (1994) Impedance control of pneumatic servo system using disturbance observer. J Autom Control Soc 30(6):667–684
Noritsugu T, Tsutomu W (1990) Control characteristics and its evaluation of pneumatic servo system. Hydraul Pneumatics 21(4):417–424
Araki K, Chen J (1996) Development of position and force control cylinder for resistance spot welding machine. Hydraul Pneumatics 27(7):941–947
Oshima Y, Araki K (1965) Servo mechanism. Ohm Corporation, Tokyuo
Atsushi Y, Tanaka H (1986) Hydraulic and pneumatic engineering. Corona Corporation, Tokyo
Tokyo precision instruments Co., Ltd. (1997) Servo valve catalog
FESTO Co., Ltd. (1997) FESTO pneumatic catalog. MPYE-5–1/4(3/8)-010B
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2019 Springer Nature Singapore Pte Ltd. and Shanghai Scientific and Technical Publishers
About this chapter
Cite this chapter
Yin, Y. (2019). Introduction. In: High Speed Pneumatic Theory and Technology Volume I. Springer, Singapore. https://doi.org/10.1007/978-981-13-5986-6_1
Download citation
DOI: https://doi.org/10.1007/978-981-13-5986-6_1
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-13-5985-9
Online ISBN: 978-981-13-5986-6
eBook Packages: EngineeringEngineering (R0)