Effects of Process Parameters on the Weld Quality During Double-Pulsed Gas Metal Arc Welding of 2205 Duplex Stainless Steel

Conference paper
Part of the Transactions on Intelligent Welding Manufacturing book series (TRINWM)

Abstract

In this paper, double-pulsed melting inert-gas welding (MIG) was conducted on 2205 duplex stainless steel and the effects of the number of strong pulses, the number of weak pulses and the welding speed were studied. The electrical parameters in the welding process were collected through the wavelet analyzer. The waveform charts of the current and voltage, the U-I diagram, the energy input, the dynamic resistance and other real-time signals were analyzed. In addition, mechanical tensile and metallographic tests were conducted. The results demonstrated that the welding speed had the highest impact on the welding quality among all the three factors, followed by the number of weak pulses and the number of strong pulses. The welded seam obtained by various numbers of strong and weak pulses was relatively uniform, indicating that the effect of the number of strong and weak pulses on the welded seam was relatively low. The tensile fracture occurred in the base material part of the duplex stainless steel, indicating that the welded seam region had a higher tensile strength than the base material. The tensile strengths of various specimens were similar. When the welding speed was reduced, the heat input increased during the welding of the welded seam, the cooling rate of the welded seam slowed down, whereas the ferrite transition duration increased, which led to the formation of higher amount of austenite and a relatively coarse structure.

Keywords

Duplex stainless steel Double pulse MIG Welding quality 

Notes

Acknowledgements

The research was sponsored by the High-level Leading Talent Introduction Program of GDAS (2016GDASRC-0106), the Natural Science Foundation of Guangdong (2016A030313117), the Industry-university-research of Guangdong province and Ministry of Education (2013B090600098).

References

  1. 1.
    Wang Z, Xu H, Wu W et al (2011) Joint performance of duplex stainless 2205 by laser MIG hybrid welding. Trans China Weld Inst 32(2):105–108Google Scholar
  2. 2.
    Wang Z, Han J, Song H et al (2011) Comparative analysis for joint performance of duplex stainless steel by different arc welding methods. Trans China Weld Inst 32(4):37–40Google Scholar
  3. 3.
    Yao P, Jiaxiang Xue, Qiang Zhu et al (2014) Quantitative evaluation of double wire pulsed welding stability based on probability density distribution. Trans China Weld Inst 35(7):51–54Google Scholar
  4. 4.
    Yao P, Xue J, Zhong L et al (2012) Intelligent process expert database of double pulse MIG welding of Al-Si alloy. Trans China Weld Inst 21(1):59–63Google Scholar
  5. 5.
    Xie H, Wang L, Sha X et al (2015) Analysis of strong and weak pulse ratio on weld quality of AA6061 aluminum alloy double pulsed gas metal arc welding. Trans China Weld Inst 36(12):77–80Google Scholar
  6. 6.
    Yoganandh J, Kannan T, Kumaresh Babu SP et al (2013) Optimization of GMAW process parameters in austenitic stainless-steel cladding using genetic algorithm based computational models. Exp Tech 37(5):48–58CrossRefGoogle Scholar
  7. 7.
    Chen H, Xue J, Heng G (2016) Improvement of double wire mig welding by using sine wave pulse modulation control method. In: IHMSC-2016 eighth international conference on intelligent human-machine systems and cybernetics, pp 451–455Google Scholar
  8. 8.
    Zhu Q, Xue J, Xu M (2015) A probe into backward median current waveform welding of aluminum alloys. J S China Univ Technol (Natural Science Edition) 43(3):15–20Google Scholar
  9. 9.
    Zhu Q, Xue J, Xu M (2016) Gaussian pulsed MIG welding of aluminum alloy sheet. Trans China Weld Inst 37(8):71–74Google Scholar
  10. 10.
    Niu Y, Xue H, Li H (2012) Effect of peak pulse voltage on metal transfer and formation of weld in double-wire pulsed MIG welding. Trans China Weld Inst 31(1):50–54Google Scholar
  11. 11.
    Aktepe A, Ersöz S, Lüy M (2014) Welding process optimization with artificial neural network applications. Neutral Netw World 24(6):655–670CrossRefGoogle Scholar
  12. 12.
    Wang LL, Wei HL, Xue JX et al (2017) A pathway to microstructural refinement through double pulsed gas metal arc welding. Scripta Mater 134:61–65CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2018

Authors and Affiliations

  1. 1.School of Mechanical and Automotive EngineeringSouth China University of TechnologyGuangzhouChina

Personalised recommendations