Abstract
At the low flow rate the recirculation occurred at the impeller outlet always induces the low frequency pressure fluctuation, which has severe influence on the safety of pumps. In order to investigate the influence of oblique trimmed impeller on the pressure fluctuation, two impellers with different exit geometry parameters were tested in the same volute. SST k-ω model was applied to the numerical simulation and the simulation results showed good agreement with the experimental results. Besides, some monitor points were arranged near the trailing edge of the impellers to record the pressure fluctuation. The internal flow field and pressure fluctuation characteristics under different flow rate conditions were also obtained. The simulation results showed that the recirculation zone near the original impeller outlet first occurred near the shroud, then moved to the hub and finally moved back to the shroud as the flow rate decrease. While the recirculation zone near the oblique trimmed impeller outlet always occurred near the hub at the low flow rate. The oblique trimmed impeller could decrease the pressure fluctuation level at the low flow rate and pressure fluctuation around the exit of the impeller at the low frequency is closely related to the recirculation phenomenon.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Solis M, Bakir F, Khelladi S. Pressure Fluctuations Reduction in Centrifugal Pumps: Influence of Impeller Geometry and Radial Gap. ASME Fluids Eng Div Summer Meet. 2009;2009:253–65.
Qin W, Tsukamoto H. Theoretical Study of Pressure Fluctuations Downstream of a Diffuser Pump Impeller—Part 2: Effects of Volute, Flow Rate and Radial Gap. J Fluids Eng. 1997; 119(3).
Alqutub A, Khalifa A, Khulief Y. Experimental investigation of the effect of radial gap and impeller blade exit on flow-induced vibration at the blade-passing frequency in a centrifugal pump. Int J Rotating Mach. 2009; 2009(1023-621X):9.
Berten S, Farhat M, Avellan F, et al. Experimental investigation of pressure fluctuations in a high-energy centrifugal pump stage at off-design conditions. Fluid Mach Congr. 2014;6–7(2014):57–66.
Pan Z, Ni Y, Ho J, et al. Flow Structures and Pressure Fluctuations in a Centrifugal Pump at Design and Off-Design Conditions. ASME Fluids Eng Div Summer Meet. 2009;2009:137–45.
Dong R, Chu S, Katz J. Effect of modification to tongue and impeller geometry on unsteady flow, pressure fluctuations, and noise in a centrifugal pump. J Turbomach. 1997; 119(3):V001T01A005.
Solis M, Bakir F, Khelladi S. Pressure Fluctuations Reduction in Centrifugal Pumps: Influence of Impeller Geometry and Radial Gap. 2009.
Alqutub A, Khalifa A, Khulief Y. Experimental investigation of the effect of radial gap and impeller blade exit on flow-induced vibration at the blade-passing frequency in a centrifugal pump. Int J Rotating Mach. 2009; 2009(1023-621X):9.
Zhang N, Yang M, Gao B, et al. Experimental Investigation on Unsteady Pressure Pulsation in a Centrifugal Pump With Special Slope Volute. J. Fluids Eng. 2015; 137(6).
Zhang N, Yang M, Gao B, et al. Unsteady pressure pulsation and rotating stall characteristics in a centrifugal pump with slope volute. Adv Mech Eng. 2014;2014(5):710791.
Liu MQ, Li QW, Bai YH, et al. Efficiency and pressure pulsation analysis of a double suction centrifugal pump with different arrangement impellers. Adv Mater Res. 2012;433–440:709–15.
Yuan J, Fu Y, Yang L, et al. Analysis on pressure fluctuation within volute of centrifugal pump based on large eddy simulation. J Drainage Irrig Mach Eng. 2010.
Zhu R S, Hu Z Q. Numerical simulation of pressure fluctuation in double-blade pump. Trans Chin Soc Agric Eng. 2010; 26(6):129–134(6).
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Cao, R., Si, Q., Sheng, G., Lin, G. (2018). Influence of the Oblique Trimmed Impeller on Pressure Fluctuations in Centrifugal Pump at Low Flow Rate. In: Tan, J., Gao, F., Xiang, C. (eds) Advances in Mechanical Design. ICMD 2017. Mechanisms and Machine Science, vol 55. Springer, Singapore. https://doi.org/10.1007/978-981-10-6553-8_16
Download citation
DOI: https://doi.org/10.1007/978-981-10-6553-8_16
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-10-6552-1
Online ISBN: 978-981-10-6553-8
eBook Packages: EngineeringEngineering (R0)