Abstract
This paper provides an overview of fabrication and design of CMOS-based microelectromechanical systems with emphasis on inertial sensor and data storage applications. High-aspect-ratio (4.4:1) microstructures can be fabricated using conventional CMOS processing followed by a sequence of maskless dry-etching steps. The CMOS dielectric and metallization layers, normally used for electrical interconnect, serve a dual function as a composite metal/dielectric structural material. Reactive-ion etching produces near vertical sidewalls, enabling micromechanical beam widths and gap spacings down to 1.2 µm. The process is tailored for design of lateral electrostatic actuators as well as capacitive position and motion sensors. Tight integration of the microstructures with CMOS provides an opportunity to make low-noise sensor interface circuitry, and to include the signal processing needed to manage arrayed sensor-and-actuator systems-on-a-chip. Novel actuator and sensor topologies can be designed by embedding multiple isolated conductors into the microstructures. An additional post-CMOS processing sequence produces platinum tips on the movable microstructures. These tips are being explored for use in probe-based data storage and tunneling sensor applications.
Keywords
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.
This is a preview of subscription content, log in via an institution.
Buying options
Tax calculation will be finalised at checkout
Purchases are for personal use only
Learn about institutional subscriptionsPreview
Unable to display preview. Download preview PDF.
Reference
Parameswaran, M., Baltes, H. P., Ristic, L., Dhaded, A. C., and Robinson, A. M. (1989) A new approach for the fabrication of micromechanical structures, Sensors and Actuators 19(3), 289–307.
Hoffman, E., Warneka, B., Kruglick, E., Weigold, J., and Pister, K. S. J. (1995) 3D structures with piezoresistive sensors in standard CMOS, in Proc. IEEE Micro Electro Mech. Sys. Workshop, Amsterdam, The Netherlands, 288–293.
Fedder, G. K., Santhanam, S., Reed, M. L., Eagle, S. C., Guillou, D. E, Lu, M. S.-C., and Carley, L. R. (1997) Laminated high-aspect-ratio structures in a conventional CMOS process, Sensors & Actuators A 57(2), 103–110.
Seidel, H., Fritsch, U., Gottinger, R., Schalk, J., Walter, J., and Ambaum, K. (1995) A piezoresistive silicon accelerometer with monolithically integrated CMOS-circuitry, in Tech. Digest of the 8th Int. Conf. on Solid-State Sensors and Actuators (Transducers ‘95), Stockholm, Sweden,1, 597–600.
Biebl, M., Scheiter, T., C. Hierold, Philipsborn, H. v., and Klose, H. (1995) Micromechanics compatible with an 0.8 tm CMOS process, Sensors and Actuators A 46–47, 593–597.
Lin, G., Pister, K. S. J., and Roos, K. P. (1996) Standard CMOS piezoresistive sensor to quantify heart cell contractile forces, in Proc. IEEE Micro Electro Mech. Sys. Workshop (MEMS ‘86), San Diego, CA, 150–155.
Mayer, F., Paul, O., and Baltes, H. (1995) Influence of design geometry and packaging on the response of thermal CMOS flow sensors, in Tech. Digest 8th Int. Conf. on Solid-State Sensors and Actuators (Transducers ‘85),Stockholm,Sweden, 1, 528–531.
Syrzycki, M. J., Carr, L., Chapman, G. H., and Parameswaran, M. (1993) A wafer scale visual to thermal converter, IEEE Trans. Compon. Hybrids Manuf. Technol., 16(7) 665–673.
Reay, R. J., Klassen, H., and Kovacs, G. T. A. (1994) Thermally and electrically isolated single crystal silicon structures in CMOS technology, IEEE Electron Device Letters, 15(10) 399–401.
Westburg, D., Paul, O., Andersson, G. I., and Baltes, H. (1997) A CMOS-compatible device for fluid density measurements, in Proc. IEEE Micro Electro Mech. Sys. Workshop (MEMS ‘87), Nagoya, Japan, 278–283.
MOSIS - VLSI Fabrication Service, USC/Information Sciences Institute, 4676 Admiralty Way, Marina del Rey, CA 90292–6695, http://www.isi.edu/mosis/.
Circuits Multi-Projets, CMP (1996) French MPC Activity Report, 46 Avenue Felix Viallet, 38031 Grenoble, France (http://tima-cmp.imag.fr).
Carley, L. R., Reed, M. L., Fedder, G. K., and Santhanam, S. (1996) Microelectromechanical structure and process of making same, U.S. patent pending.
Tang, W. C., Nguyen, T.-C. H., Judy, M. W., and Howe, R. T. (1990) Electrostatic-comb drive of lateral polysilicon resonators, Sensors andActuators A 21(1–3), 328–331.
Gianchandani, Y. B., and Najafi, K. (1996) Bent-beam strain sensors, J. of MicroElectroMech. Sys., 5(1), 52–58.
Kranz, M. S., and Fedder, G. K. (1997: in press) Micromechanical vibratory rate gyroscopes fabricated in conventional CMOS, in Proc. Symposium Gyro Technology, Stuttgart, Germany.
Author information
Authors and Affiliations
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 1998 Springer Science+Business Media Dordrecht
About this paper
Cite this paper
Fedder, G.K. (1998). Integrated MEMS in Conventional CMOS. In: Bhushan, B. (eds) Tribology Issues and Opportunities in MEMS. Springer, Dordrecht. https://doi.org/10.1007/978-94-011-5050-7_2
Download citation
DOI: https://doi.org/10.1007/978-94-011-5050-7_2
Publisher Name: Springer, Dordrecht
Print ISBN: 978-94-010-6121-6
Online ISBN: 978-94-011-5050-7
eBook Packages: Springer Book Archive