Advertisement

Barrel Finishing Technology

  • Shengqiang YangEmail author
  • Wenhui Li
Chapter
  • 687 Downloads

Abstract

In the process of the free abrasive tool finishing, the abrasive tool (also known as media) is in a free state, which is based on relative motions and action forces caused by the direct contact with parts to complete the finishing of part surface and to increase the surface qualities of parts.

References

  1. 1.
    S.C. Yang, M.Z. Wang, Y.X. Zhang, Surface Quality and Finishing (Machinery Industry Press, Beijing, 2000)Google Scholar
  2. 2.
    W.H. Li, Surface Barrel Finishing Technology Theory and Practical Study (Taiyuan University of Technology, Taiyuan, 2009)Google Scholar
  3. 3.
    W.H. Li, S.C. Yang, S.Q. Yang. Experimental research of affecting main performance of the engine by surface finishing technology[G]. Proceedings of the International Conference on Surface Finishing Technology and Surface Engineering, Frontiers of Design and Manufacturing, 2006Google Scholar
  4. 4.
    S.Q. Yang, W.H. Li, S.C. Yang, Experimental research on improving performance of the engine by surface finishing technology. Trans. Chin. Soc. Agric. Mach. 37(2), 17–20 (2006)Google Scholar
  5. 5.
    A.F. Kenton, Back to the basis of surface finishing. Met. Finish. 105(10), 84–85 (2007)CrossRefGoogle Scholar
  6. 6.
    L. Li, Barrel finishing technology and process. For. Mach. Woodwork. Equip. 32(2), 46–48 (2004)Google Scholar
  7. 7.
    S.C. Yang, H.F. Li, The application and development of our precision surface finishing and deburring technology. New Technol. New Process 3, 35–36 (1995)Google Scholar
  8. 8.
    S.C. Yang, M.Z. Wang, S.Q. Yang, Surface quality and barrel finishing technology. Shan Dong Intern. Combust. Engine 1, 14–16 (2001)Google Scholar
  9. 9.
    S.C. Yang, S.Q. Yang, The development direction of the free abrasive finishing technology. Machinist Met. Cutting 1, 11–12 (2002)Google Scholar
  10. 10.
    S.Q. Yang, S.C. Yang, G.L. Liu, Application examples of barrel finishing technology. Mach. Manufact. Eng. 11, 21–23 (1999)Google Scholar
  11. 11.
    W.H. Li, S.Q. Yang, S.C. Yang, Theoretic analysis and experimental research on barrel finishing uniformity of crank shafts with larger size. Key Eng. Mater. 359–360, 394–398 (2008)CrossRefGoogle Scholar
  12. 12.
    W.H. Li, S.Q. Yang, S.C. Yang, Theoretic analysis and simulation on horizontal spindle barrel finishing. Key Eng. Mater. 416, 332–336 (2009)CrossRefGoogle Scholar
  13. 13.
    W.H. Li, S.Q. Yang, S.C. Yang, Technique and theoretical analysis for the finishing of large discal parts. Comput. Appl. Technol. 29(2–4), 168–172 (2007)CrossRefGoogle Scholar
  14. 14.
    W.H. Li, S.Q. Yang, S.C. Yang, Technique project and theoretic research on surface finishing to the wheel hub. Key Eng. Mater. 375–376, 385–389 (2008)Google Scholar
  15. 15.
    研磨布紙加工技術研究会. 新しい研磨技術[M]. ォ一ム社, 1992Google Scholar
  16. 16.
    田中羲信, 津和秀夫, 井川直哉. 精密工作法[M]. 共立出版, 1995Google Scholar
  17. 17.
    木下直治, 高哲孝哉. 精度設計と部品仕上システム技術[M]. 日經技術圖書株式會社, 1990Google Scholar
  18. 18.
    A. Boschetto, A. Ruggiero, F. Veniali, Deburring of sheet metal by barrel finishing. Key Eng. Mater. 344, 193–200 (2007)CrossRefGoogle Scholar
  19. 19.
    C.X. Long, An acting force analysis on vibrating tumbling machine. Bearing 1, 27–32 (1989)Google Scholar
  20. 20.
    S. Wang, R.S. Timsit, J.K. Spelt, Experimental investigation of vibratory finishing of aluminum. Wear 243, 147–156 (2000)CrossRefGoogle Scholar
  21. 21.
    M.R. Baghbanan, A. Yabuki, R.S. Timsit et al., Tribological behavior of aluminum alloys in a vibratory finishing process. Wear 255(7–12), 1369–1379 (2003)CrossRefGoogle Scholar
  22. 22.
    J. Domblesky, R. Evans, V. Cariapa, Material removal model for vibratory finishing. Int. J. Prod. Res. 42(5), 1029–1041 (2004)CrossRefGoogle Scholar
  23. 23.
    D. Ciampini, M. Papini, J.K. Spelt, Impact velocity measurement of media in a vibratory finisher. J. Mater. Process. Technol. 183, 347–357 (2007)CrossRefGoogle Scholar
  24. 24.
    David A. Davidson, Mass finishing processes. Met. Finish. 105(10), 72–83 (2007)CrossRefGoogle Scholar
  25. 25.
    A. Yabuki, M.R. Baghbanan, J.K. Spelt, Contact forces and mechanisms in a vibratory finisher. Wear 252, 635–643 (2002)CrossRefGoogle Scholar
  26. 26.
    Y.Y. Guo, Y.X. Zhang, Principle analysis of gyro-finishing. Instrum. Tech. Sens. 1996(5): 17–19, 21Google Scholar
  27. 27.
    S.L. Shi, M.Z. Wang, Y.X. Zhang, Discussion cyclone barrel polishing polished crankshaft. Intern. Combust. Engines 6, 14–17 (1994)Google Scholar
  28. 28.
    S.L. Shi, Y.X. Zhang, S.C. Yang, Experimental research of whirling barrel finishing. Instrum. Tech. Sens. 4, 14–16 (1994)Google Scholar
  29. 29.
    S.Q. Yang, H.F. Li, D.G. Hou. Whirling barrel finishing technology and application[J].New Technology & New Process, 1995(6): 19–20Google Scholar
  30. 30.
    M.Z. Wang, Y.W. Wang, J.J. Wang, in Analysis of Centrifugal Barrel Finishing Principle. International Conference Proceedings of Second-precision Surface Finishing and Deburring Technology (Machinery Industry Press, Dalian, 1992)Google Scholar
  31. 31.
    H.C. Wang, Q.M. Cai, The rotary power analysis of planetary roller polishing machine. Tianjin Text. Inst. Technol. 16(5), 35–39 (1997)Google Scholar
  32. 32.
    H.C. Wang, T.W. Chen, D.L. Zhang, et al., in Experimental and Theoretical Study on the Factor of Productivity in the Centrifugal Polishing Process. Proceedings of the International Conference on Surface Finishing Technology and Surface Engineering, Frontiers of Design and Manufacturing (2006)Google Scholar
  33. 33.
    M.Z. Wang, Barrel finishing process. New Technol. New Process, 1995(5): 18–19Google Scholar
  34. 34.
    P.K. Zhang, H.L. Wang, New technology of complex shaft outer surface finishing. Machinery 39(446), 13–14 (2001)Google Scholar
  35. 35.
    H.C. Wang, H.T. Zhang, Q. Wang et al., Experiment study on the dynamic characteristics of the abrasive flow in centrifugal grinding. Key Eng. Mater. 304–305, 369–373 (2006)CrossRefGoogle Scholar
  36. 36.
    T.W. Chen, Theoretical and Experimental Research of Abrasive Flow Regime Characterized by Centrifugal Grinding Process. Tianjin Polytechnic University, Tianjin (2007)Google Scholar
  37. 37.
    D.L. Zhang, X. Fang, Motion characteristics of abrasive blocks in the barrel with FLUENT software. CFD China.com, 2004(3): 10–47Google Scholar
  38. 38.
    Z. Li, The Optimization and Application of DEM Simulation in Centrifugal Barrel Finishing Process. Taiyuan University of Technology, Taiyuan (2016)Google Scholar
  39. 39.
    W.H. Li, L. Zhang, X.H. Li, S.Q. Yang, Discrete element simulation of particle behavior in mass finishing process: a parametric study. J. Balkan Tribol. Assoc. 22(3), 2731–2750 (2016)Google Scholar
  40. 40.
    A. Sofronas, S. Taraman, Model development and optimization of vibratory finishing process. Int. J. Prod. Res. 17, 23–31 (1979)CrossRefGoogle Scholar
  41. 41.
    David A. Davidson, Precision finishing processes in centrifugal barrel equipment. Met. Finish. 104(7–8), 65–67 (2006)CrossRefGoogle Scholar
  42. 42.
    K. Kitajima, A. Yamamoto, M. Sasai, Finishing characteristics and residual stress on workpiece surface in dry barrel finishing. Key Eng. Mater. 257–258, 189–194 (2004)CrossRefGoogle Scholar
  43. 43.
    S.L. Shi, M.Z. Wang, Y.X. Zhang, Centrifugal barrel finishing principle and examples. Acta Armamentarii 17(3), 230–233 (1996)Google Scholar
  44. 44.
    S.Q. Yang, Centrifugal barrel finishing technology and selection of practical process. Grinder and Grinding, 1997(3): 62–63Google Scholar
  45. 45.
    Y.X. Zhang, Y.Y. Guo, Analysis of principle and experiment of centrifugal barrel finishing. J. Shanxi Agric. Univ. 14(3), 320–322 (1994)Google Scholar
  46. 46.
    Mass Finishing Inc. Centrifugal barrel finishing machines. Met. Finish. 101(11), 49 (2003)Google Scholar
  47. 47.
    David A. Davidson, Surface finishing reaches new heights. Met. Finish. 103(3), 25–28 (2005)CrossRefGoogle Scholar
  48. 48.
    S.Q. Yang, S.C. Yang, M.Z. Wang, The technological plan and theory analysis of skew spindle high pressure finishing. China Mech. Eng. 10(4), 397–400 (1999)Google Scholar
  49. 49.
    S.Q. Yang, M.Z. Wang, Y.W. Wang, Experimental equipment and experimental research of skew spindle high pressure finishing. China Mech. Eng. 10(5), 502–505 (1999)Google Scholar
  50. 50.
    S.Q. Yang, Y.W. Wang, S.C. Yang, The comprehensive improvement of skew spindle high pressure finishing to parts surface integrity. China Mech. Eng. 10(6), 626–629 (1999)Google Scholar
  51. 51.
    W.H. Li, S.C. Yang, S.Q. Yang, Study of shaft planar barrel finishing. J. Taiyuan Univ. Technol. 33(1), 51–53 (2002)Google Scholar
  52. 52.
    W.H. Li, S.C. Yang, S.Q. Yang, Experiment of finishing crank parts with spindle planetary barrel finishing. J. Taiyuan Univ. Technol. 33(1), 166–168 (2002)Google Scholar
  53. 53.
    S.Q. Yang, M.Z. Wang, S.C. Yang, Crankshafts’ parts of barrel finishing technology development and research. China Mech. Eng. 12(3), 300–302 (2001)Google Scholar
  54. 54.
    W.H. Li, S.C. Yang, S.Q. Yang, Process characteristics research on horizontal spindle barrel finishing. Adv. Mater. Res. 53–54, 15–19 (2008)CrossRefGoogle Scholar
  55. 55.
    W.H. Li, H.L. Chen, S.Q. Yang, in Process Characteristics and Finishing Effects Research on Horizontal Spindle Barrel Finishing. The 4th IEEE Conference on Industrial Electronics and Applications (2009)Google Scholar
  56. 56.
    W.H. Li, S.Q. Yang, S.C. Yang, in Development and Experimental Research of Machining Medium in Barrel Finishing. Proceedings of the International Conference on Surface Finishing Technology and Surface Engineering, Frontiers of Design and Manufacturing (2006)Google Scholar
  57. 57.
    Y.W. Wang, S.Q. Yang, S.C. Yang et al., Effects of chip performance parameters on the effectiveness in barrel finishing. J. Taiyuan Univ. Technol. 26(4), 46–52 (1995)Google Scholar
  58. 58.
    G.L. Liu, T. Lv, Mechanism analysis and practice of surface barrel finishing. Mach. Manuf. Eng. 4, 13–15 (1999)Google Scholar
  59. 59.
    W.H. Li, H.L. Chen, S.Q. Yang, Surface integrity research on barrel finishing of Crankshafts’ Part. Key Eng. Mater. 392–394, 655–660 (2009)CrossRefGoogle Scholar
  60. 60.
    GB/T 10095-2008, Cylindrical Gears-System of Accuracy. China Standards Press, Beijing (2008.9.1)Google Scholar
  61. 61.
    M. Massarsky, D.A. Davidson, Turbo-abrasive machining and finishing. Met. Finish. 95(7), 29 (1997)CrossRefGoogle Scholar
  62. 62.
    Z. Yue, H.B. Jiang, J.Q. Yu et al., Experimental research of techniques for few-hour test run in medium-and small-power diesel engine. Intern. Combust. Engines 1, 25–29 (2002)Google Scholar
  63. 63.
    Z. Yue, H.B. Jiang, L.F. Min, Application finishing technology to improve diesel engine running test specification. Shandong Intern. Combust. Engine 1, 6–8 (2001)Google Scholar

Copyright information

© The Editor(s) (if applicable) and The Author(s) 2018 2018

Authors and Affiliations

  1. 1.College of Mechanical EngineeringTaiyuan University of TechnologyTaiyuanChina
  2. 2.College of Mechanical EngineeringTaiyuan University of TechnologyTaiyuanChina

Personalised recommendations