Abstract
Models for the convective heat transfer from the combustion gases to the walls inside a spark ignition engine are an important keystone in the simulation tools which are being developed to aid engine optimization. The existing models are, however, inaccurate for an alternative fuel like hydrogen. This could be caused by an inaccurate prediction of the effect of the gas properties. These have never been varied in a wide range before, because air and ‘classical’ fossil fuels have similar values, but they are significantly different in the case of hydrogen. We have investigated the effect of the gas properties on the heat flux in a spark ignition engine by injecting different inert gases under motored operation and by using different alternative fuels under fired operation. Design of Experiments has been applied to vary the engine factors in a systematic way over the entire parameter space and to determine the minimum required amount of combinations. This paper presents the validation of a heat transfer model based on the Reynolds analogy for the entire experimental dataset. The paper demonstrates that the heat flux can be accurately predicted during the compression stroke with a constant characteristic length and velocity, if appropriate polynomials for the gas properties are used. Furthermore, it shows that a two-zone combustion model needs to be used as a first step to capture the effect of the flame propagation. However, alternative characteristic lengths and velocities will need to be investigated to capture the intensified convective heat transfer caused by the propagating flame front and to accurately predict the heat flux during the expansion stroke.
F2012-A07-004
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Borman GL, Nishiwaki K (1987) Internal-combustion engine heat-transfer. Prog Energy Combust Sci 13(1):1–46
Demuynck J, De Paepe M, Sierens R, Vancoillie J, Verhelst S (2011) Literature review on the convective heat transfer measurements in spark ignition engines. In: 13th European automotive congress (EAEC 2011), paper EAEC2011_A46. Valencia, Spain
Annand WJD (1963) Heat transfer in the cylinders of reciprocating internal combustion engines. Proc Instn Mech Engrs 177(36):973–996
Morel T, Rackmil CI, Keribar R, Jennings MJ (1988) Model for heat transfer and combustion in spark ignited engines and its comparison with experiments. SAE paper 880198
Woschni G (1967) A universally applicable equation for the instantaneous heat transfer coefficient in the internal combustion engine. SAE paper 670931
Welty JR, Wicks CE, Wilson RE, Rorrer GL (2001) Fundamentals of momentum, heat and mass transfer, 4th edn. Wiley, New York
Demuynck J, De Paepe M, Huisseune H, Sierens R, Vancoillie J, Verhelst S (2011) On the applicability of empirical heat transfer models for hydrogen combustion engines. Int J Hydrogen Energy 36(1):975–984
Shudo T, Suzuki H (2002) Applicability of heat transfer equations to hydrogen combustion. JSAE Rev 23(3):303–308
Kleinschmidt W (1999) Instationäre Wärmeübertragung in Verbrennungsmotoren: Theorie, Berechnung und Vergleich mit Versuchsergebnissen. Fortschr.-Ber. VDI Reihe 12 nr. 383. Düsseldorf: VDI Verlag
Demuynck J, De Paepe M, Vancoillie J, Sileghem L, Verhelst S (2012) Applying design of experiments to determine the effect of gas properties on in-cylinder heat flux in a motored SI engine. SAE Int J Engines 5(3)
Berger PD (2002) Experimental design with applications in management, engineering, and the sciences. Duxbury, Belmont. ISBN 0-534-35822-5
GT-Power (2009) Engine performance application manual. Gamma Technologies
Rowley RL, Wilding WV, Oscarson JL, Yang Y, Zundel NA, Daubert TE, Danner RP (2003) DIPPR® data compilation of pure compound properties. Design Institute for Physical Properties, AIChE, New York
Reid RC, Prausnitz JM, Poling BE (1988) The properties of Gases and Liquids, 0–07-100284-7. McGraw-Hill Book Co, Singapore
Chang J, Guralp O, Filipi Z, Assanis D (2004) New heat transfer correlation for an HCCI engine derived from measurements of instantaneous surface heat flux. SAE paper 2004-01-2996
Acknowledgments
The authors of this paper like to acknowledge the technical assistance of Koen Chielens and Patrick De Pue. The research is carried out in the framework of a Ph.D. which is funded by a grant (SB-81139) of the Institute for the Promotion of Innovation through Science and Technology in Flanders (IWT-Vlaanderen). The experimental equipment is funded by a Research Grant (1.5.147.10 N) of the Research Foundation—Flanders (FWO). These financial supports are gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2013 Springer-Verlag Berlin Heidelberg
About this paper
Cite this paper
Demuynck, J., Chana, K., De Paepe, M., Sileghem, L., Vancoillie, J., Verhelst, S. (2013). Applying Design of Experiments to Develop a Fuel Independent Heat Transfer Model for Spark Ignition Engines. In: Proceedings of the FISITA 2012 World Automotive Congress. Lecture Notes in Electrical Engineering, vol 190. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-642-33750-5_27
Download citation
DOI: https://doi.org/10.1007/978-3-642-33750-5_27
Published:
Publisher Name: Springer, Berlin, Heidelberg
Print ISBN: 978-3-642-33749-9
Online ISBN: 978-3-642-33750-5
eBook Packages: EngineeringEngineering (R0)