Abstract
Cutting processes are employed to generate functional components. Finally, the surface and subsurface properties of the components are decisive for the functioning and durability. It is not always possible to draw a sharp line between surface and subsurface as shown by the definition of the terms. In a general sense, the surface describes the outer limitation of a body. In mathematics, the surface determines the mass of all the boundary points of a body. In science, the surface is the limit between two media. In production technology, a further specification of the term becomes necessary.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Bauer, M. H.: Messen der Oberflächengüte [Measuring of surface quality]. Maschinenbau—Der Betrieb 13(3–4), 81–83 (1934)
Brammertz, P.-H.: Die Entstehung der Oberflächenrauheit beim Feindrehen [The generation of surface roughness in finishing]. Industrie Anzeiger 83(2), 25–32 (1961)
Breidenstein, B.: Oberflächen und Randzonen hoch belasteter Bauteile [Surfaces and subsurface zones of highly loaded components]. Habilitationsschrift Leibniz Universität Hannover (2011)
Brinksmeier, E.: Prozess- und Werkstückqualität in der Feinbearbeitung [Process- and workpiece-quality in finishing]. Habilitationsschrift Universität Hannover (1991)
Bunge, H. J.: Mathematische Methoden der Texturanalyse [Mathematical methods of the texture analysis]. Akademie-Verlag, Berlin (1969)
Gestaltabweichungen; Begriffe, Ordnungssystem/Form deviations; concepts; classification system (1982)
Oberflächen an Teilen für Maschinenbau und Feinwerktechnik/Surfaces of components used in mechanical engineering and light engineering; terminology according to stress conditions (1982)
Ermittlung der Rauheitskenngrößen Ra, Rz, Rmax mit elektrischen Tastschnittgeräten; Begriffe, Messbedingungen/Determination of values of surface roughness parameters Ra, Rz, Rmax using electrical contact (stylus) instruments; concepts and measuring conditions (1990)
Kreissig, U.: Rissprüfung—in einer Sekunde zum Ergebnis [Crack test—in one second to the result]. Report MTU Aero Engines, Sommer/Herbst, S. 24–25 (2005)
Mathar, J.: Ermittlung von Eigenspannungen durch Messung von Bohrloch-Verformungen [Determination of residual stresses by measuring of borehole deformations]. Archiv für Eisenhüttenwesen 6, 277–281 (1933)
Nedeß, C.: Breitschlichtdrehen. Dr.-Ing. Diss. Univ. Hannover [Broad tool finish turning], München: Technischer Verlag Resch (1975)
Paucksch, E.; Holsten, S.; Linß, M.; Tikal, F.: Zerspantechnik—Prozesse, Werkzeuge, Technologien [Cutting technology—processes, tools, techniques]. 12. Auflage, Vieweg und Teubner Verlag, GWV Fachverlage Wiesbaden (2008)
Plöger, J. M.: Randzonenbeeinflussung beim Hochgeschwindigkeitsdrehen [Subsurface influencing in high speed turning]. Dr.-Ing. Diss. Universität Hannover (2002)
Roos, E.; Maile, K.: Werkstoffkunde für Ingenieure [Material science for engineers]. 2. Auflage, Springer Verlag, Berlin, Heidelberg (2005)
Schlengermann, U.: Ultraschall-Werkstoffprüfung—Das Krautkrämer Taschenbuch [Ultrasonic material testing—the Krautkraemer handbook]. Vulkan-Verlag, Essen (1992)
Schwarz, T.: Beitrag zur Eigenspannungsermittlung an isotropen, anisotropen sowie inhomogenen, schichtweise aufgebauten Werkstoffen mittels Bohrlochmethode und Ringkernverfahren [Contribution to the determination of residual stresses at isotropic, anisotropic and inhomogenious layerwise constructed materials by the borehole method and ring core method]. Dr.-Ing. Diss. Universität Stuttgart (1996)
Tönshoff, H. K.: Eigenspannungen und plastische Verformungen im Werkstück durch spanende Bearbeitung [Residual stresses and plastic deformations at the workpiece through cutting and abrasive processes]. Dr.-Ing. Diss. Univ. Hannover (1965)
Tönshoff, H. K.; Brinksmeier, E.: Determination of mechanical and thermal influences on machined surfaces by microhardness and Residual Stress Analysis. Ann. CIRP 29(2), 519–530 (1980)
Tönshoff, H. K.; Brinksmeier, E.; Hetz, F.: Detection of microcracks. Ann CIRP 36 2, 545–552 (1987)
Tönshoff, H. K.; Wobker, H.-G.; Kroos, F.: Improving surface integrity of finished surfaces of case hardened steel by water peening. International Symposium for Electromachining, I SEM-XI, 17–20 Apr 1995, CH-Lausanne
Tönshoff, H. K., Denkena, B.; Ben Amor, R.; Ostendorf, A.; Stein, J.; Hollmann, C.; Kuhlmann, A.: Spanbildung und Temperaturen beim Spanen mit hohen Geschwindigkeiten [Chip formation and temperatures in cutting with high speeds]. In: Tönshoff, H. K.; Hollmann, F. (Hrsg.): Hochgeschwindigkeitsspanen metallischer Werkstoffe. Wiley-VCH Verlag (2005)
Volk, R.: Rauheitsmessung—Theorie und Praxis [Measurement of roughness—theory and practice]. Beuth Verlag, Berlin (2005)
Vrana, J.: Grundlagen und Anwendungen der aktiven Thermographie mit elektromagnetischer Anregung [Basics and applications of the active thermography by electromagnetic excitation]. Dr.-Ing. Diss. Universität Saarbrücken (2008)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2013 Springer-Verlag Berlin Heidelberg
About this chapter
Cite this chapter
Tönshoff, H.K., Denkena, B. (2013). Surface and Subsurface Properties. In: Basics of Cutting and Abrasive Processes. Lecture Notes in Production Engineering. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-642-33257-9_16
Download citation
DOI: https://doi.org/10.1007/978-3-642-33257-9_16
Published:
Publisher Name: Springer, Berlin, Heidelberg
Print ISBN: 978-3-642-33256-2
Online ISBN: 978-3-642-33257-9
eBook Packages: EngineeringEngineering (R0)