Abstract
Based on the transfer-matrix method and taking into consideration the gyroscopic couple, the shear, the variable cross-section and other influential factors, a critical speed model was established for the multi-disk rotor of the rotor-bearing system of the grinder spindle. The critical speeds of first three orders, the modes of variation and other dynamic characteristic parameters of the grinder spindle were numerical investigated and calculated. The influences of the axial pre-tightening force of the bearing, the span of the fulcrum bearing as well as the changes in the front and rear overhangs on the critical speed of the rotor-bearing system on the grinder spindle and their pattern of changes were analyzed. The results showed that the working speed of the spindle system is much lower than the primary critical speed and can therefore stay away the resonance range effectively. Furthermore, the span of the fulcrum bearing and the overhang had significant influences on the critical speed within a certain range, and the study provided the basis and guidance for the structural design and performance optimization of the grinder spindle.
Keywords
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
References
Chen, J.-S., Chen, K.-W.: Bearing Load Analysis and Control of a Motorized High Speed Spindle. International Journal of Machine Tools & Manufacture 45, 1487–1493 (2005)
Lee, D.S., Choi, D.H.: Reduced weight design of a flexible rotor with ball bearing stiffness characteristics varying with rotational speed and load. Journal of Vibration and Acoustics-transactions of the ASME 122, 203–208 (2000)
Li, C.H., Hou, Y.L., Ding, Y.C., Cai, G.Q.: Feasibility investigations on compound process: a novel fabrication method for finishing with grinding wheel as restraint. International Journal of Computational Materials Science and Surface Engineering 4, 55–68 (2011)
Morgan, M.N., Jackson, A.R., Wu, H.: Optimisation of fluid application in grinding. CIRP Annals-Manufacturing Technology 57, 363–366 (2008)
Moulik, P.N., Yang, H.T.Y., Chandrasekar, S.: Simulation of thermal stresses due to grinding. International Journal of Mechanical Sciences 43, 831–851 (2001)
Stephenson, D.J., Jin, T., Corbett, J.: High efficiency deep grinding of a low alloy steel with plated CBN wheels. Annals of the CIRP 51, 241–244 (2002)
Li, C.H., Hou, Y.L., Liu, Z.R., Ding, Y.C.: Investigation into temperature field of nano-zirconia ceramics precision grinding. International Journal of Abrasive Technology 4(2), 77–89 (2011)
Li, C.H., Hou, Y.L., Fang, Z., Ding, Y.C.: Analytical and Experimental Investigation of Grinding Fluid Hydrodynamic Pressure at Wedge-shaped Zone. International Journal of Abrasive Technology 4(2), 163–179 (2011)
Author information
Authors and Affiliations
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2011 Springer-Verlag Berlin Heidelberg
About this paper
Cite this paper
Li, C.H., Han, Z.L., Du, C., Ding, Y.C. (2011). Numerical Study on Critical Speed Modeling of Ultra-High Speed Grinder Spindle. In: Tan, H., Zhou, M. (eds) Advances in Information Technology and Education. Communications in Computer and Information Science, vol 201. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-642-22418-8_29
Download citation
DOI: https://doi.org/10.1007/978-3-642-22418-8_29
Publisher Name: Springer, Berlin, Heidelberg
Print ISBN: 978-3-642-22417-1
Online ISBN: 978-3-642-22418-8
eBook Packages: Computer ScienceComputer Science (R0)