Abstract
As described in the previous chapters, HRS have been developed to promote energy efficient design and to consequently reduce energy requirements in the buildings sector. However, zero energy buildings and passive design buildings, whose thermal performance should be evaluated in their free running operation mode, are not a target in current HRS. The main purpose of this book is to recommend the evaluation of the free running performance of buildings on the basis of thermal comfort instead of energy consumption. A major question is whether an energy efficient building is one that demonstrates efficient performance in the free running operation mode.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Notes
- 1.
- 2.
Small houses compared to large houses usually are penalized in the star rating scheme because of the basis of rating (MJ/m2), which was discussed in Sect. 2.4.3. AccuRate has addressed this concern by developing an area correction factor (Isaacs, 2005).
- 3.
For more accuracy in calculating thermal neutrality and the thermostat setting, the mean monthly temperature should be computed for hourly temperatures rather than max/min temperatures.
- 4.
This information is based on the AccuRate manual and the help option in the software (2005).
- 5.
(ABS) http://www.abs.gov.au/
- 6.
Australia Bureau Statistic (ABS) “Time Use Survey” Cat. No. 4153.
- 7.
Note: The three conditioned zones are the minimum zones in a house in which the occupied time and occupants’ activities differ. This is the condition considered in some HERS such as NatHERS.
- 8.
A comparison was made between the hourly temperature of the living zone and the suspended floor for one of the LW typical houses in the free running operation mode when R2 insulation was added under the suspended floor. The following figure shows the hourly zone temperature for a warm and cold day respectively, on the 15th of January and of July. Both figures illustrate that the temperature of the suspended floor zone is closer to thermal comfort temperature than the temperature of the living zone for more hours of the day. Floor insulation restricts heat transfer between these two zones and therefore in effect reduces the benefits of a suspended floor for a free running building in such ambient conditions.
Comparison between temperature of living zone and sub floor zone of a lightweight house for 15th July and January in the Sydney climate.
Comparison between temperature of living zone and sub floor zone of a lightweight house for 15th July and January in the Sydney climate.
- 9.
Standard mass refers to a house with brick veneer RFL in external walls, R2.5 in the ceiling and no floor insulation.
- 10.
AccuRate software counts the effect of air ventilation for prediction of cooling energy requirements (see se Sect. 4.1.2.2 for more clarification).
- 11.
There are several selection methods for specifying how independent variables are entered into an analysis. These methods are: enter, stepwise, remove, backward and forward. Enter is a procedure for variable selection in which all variables in a block are entered in a single step.
References
Akbari, H., Samano, D., Mertol, A., Bauman, F., Kammerud, R.: The effect of variations in convection coefficients on thermal energy storage in buildings part I – interior partition walls. Energy Build. 9(3), 195–211 (1986)
Al-Homoud, M.S.: Computer-aided building energy analysis techniques. Build. Environ. 36(4), 421–433 (2000)
ASHRAE: ASNI/ASHRAE Standard 55-2004, Thermal Environmental Conditions for Human Occupancy. American Society of Heating, Refrigeration and Air Conditioning Engineers, Inc, Atlanta, GA (2004)
Auliciems, A., Szokolay, S.V.: Thermal Comfort. PLEA in association with Department of Architecture, University of Queensland, Brisbane (1997)
Australian Bureau of Meteorology: (2006). Accessed 15 Sep 2007, from http://www.bom.gov.au/lam
Ballinger, J.A.: The nationwide house energy rating scheme for Australia (BDP environment design guide no. DES 22). The Royal Australian Institute of Architects, Canberra (1998a)
Ballinger, J.A., Cassell, D.: Solar efficient housing and NatHERS: an important marketing tool. Proceedings of the Annual Conference of the Australian and New Zealand Solar Energy Society, pp. 320–326. Sydney (1994).
Bansal, N.K., Garg, S.N., Kothari, S.: Effect of exterior surface colour on the thermal performance of buildings. Build. Environ. 27(1), 31–37 (1992)
Beirlant, J., Goegebeur, Y., Teugels, J., Segers, J.: Multivariate extreme value theory. In: Statistics of Extremes: Theory and Applications. Wiley, Chichester (2005)
Ben-Nakhi, A.E., Mahmoud, M.A.: Cooling load prediction for buildings using general regression neural networks. Energy Convers. Manage. 45(13–14), 2127–2141 (2004)
Bordass, B., Leaman, A.: Occupancy- post-occupancy evaluation. In: Preiser, W.F.E., Vischer, J.C. (eds.) Assessing Building Performance, Elsevier, Sydney (2005)
Cammarata, G., Fichera, A., Marletta, L.: Sensitivity analysis for room thermal response. Int. J. Energy Res. 17, 709–718 (1993)
Clarke, J.A.: Energy Simulation in Building Design, 2nd ed. Adam Hilger, Oxford and Boston, MA (2001)
Clarke, D.: The Importance of Being Accurate (The Role and Importance of Thermal Modelling in Reducing Energy Consumption in Australian Buildings (No 1)). Association of Building Sustainability Assessors, Surry Hills (2006)
Delsante, A.: Computer User Manual for Program CHEETAH. CSIRO Division of Building Research, Melbourne (1987)
Delsante, A.: A Comparison of CHENATH, the Nationwide House Energy Rating Scheme Simulation Engine, with Measured Test Cell Data, Renewable Energy: The Future in Now, pp. 441–446. Australia and New Zealand Solar Energy Society, Hobart (1995a)
Delsante, A.: Using the Building Energy Simulation Test (Best Test) to Evaluate CHENATH, the Nationwide House Energy Rating Scheme Simulation Engine, Renewable Energy: The Future in Now, pp. 447–453. Australia and New Zealand Solar Energy Society, Hobart (1995b)
Delsante, A.: A Validation of the “AccuRate” Simulation Engine Using BESTEST (no. CMIT(C)-2004-152). CSIRO, Canberra (2004)
Delsante, A.: Is the New Generation of Building Energy Rating Software up to the Task? – A Review of AccuRate, ABCB Conference, Building Australia’s Future 2005. CSIRO Manufacturing and Infrastructure Technology, Surfers Paradise (2005)
Drysdale, J.W.: Designing Houses for Australian Climates, 3rd ed. Australian Government Publishing Service, Canberra (1975)
Energy Efficient Strategies: Comparative Cost Benefit Study of Energy Efficiency Measures of Class 1 Buildings and High Rise Apartments in Victoria (Final report for the Sustainable Energy Authority of Victoria). Melbourne (2002)
Fisette, P. (2003). Windows: Understanding Energy Efficient Performance. Accessed 6 June 2008 from http://www.umass.edu/bmatwt/publications/articles/windows_understanding_energy_efficient_performance.html
Foster, R.: Setting Occupancy Factors for Thermal Performance Modelling of Australian Households. Energy Efficient Strategies, Victoria (2006)
Givoni, B.: Man, Climate and Architecture. Applied Science Publishers Ltd, London (1976)
Gunst, R.F., Mason, R.L.: Regression Analysis and Its Application: A Data Oriented Approach. Marcel Dekker, New York, NY (1980)
Hanby, V.I.: Error estimation in bin method energy calculations. Appl. Energy. 52(1), 35–45 (1995)
Hong, T., Chou, S.K., Bong, T.Y.: Building simulation: an overview of developments and information sources. Build. Environ. 35(4), 347–361 (2000)
Hyde, R.: Climatic design: a study of housing in the hot humid tropics. The Proceedings of the Australian and New Zealand Energy Society, Darwin (1996)
Hyde, R.: Climate Responsive Design: A Study of Buildings in Moderate and Hot Humid Climates. E & FN Spon, New York, NY (2000)
Isaacs, T.: Revision of the Energy Efficiency Provisions for Housing to Better Allow for the Impact of Ventilation. ABCB, Canberra (2004)
Isaacs, T.: AccuRate: 2nd Generation Nationwide House Energy Rating software. The Royal Australian Institute of Architects, Canberra (2005)
Klainsek, J.C.: Glazing and its influence on building energy behaviour. Renewable Energy. 1(3–4), 441–448 (1991)
Klein, S.A.: Computer in the design of passive solar systems. Passive Solar J. 2(1), 57–74 (1983)
Kordjamshidi, M., Khodakarami, J., Nasrollahi, N.: Occupancy scenarios and the evaluation of thermal performances of buildings. Proceeding of ANZSES conference, Townsville, Australia (2009)
Kordjamshidi, M., King, S.: Overcoming problems in house energy ratings in temperate climates: a proposed new rating framework. Energy Build. J. 41(1), 125–132 (2009)
Kordjamshidi, M., King, S., Prasad, D.: An alternative basis for a home energy rating scheme (HERS). Proceedings of PLEA, Environmental Sustainability: The Challenge of Awareness in Developing Societies, pp. 909–914. Lebanon (2005a)
Kordjamshidi, M., King, S., Prasad, D.: Towards the development of a home rating scheme for free running buildings. Proceedings of ANZSES, Renewable Energy for a Sustainable Future – A Challenge for A Post Carbon World. Dunedin University, New Zealand (2005b)
Lam, J.C., Hui, S.C.M.: Sensitivity analysis of energy performance of office buildings. Build. Environ. 31(1), 27–39 (1996)
Lee, T., Snow, M.: The Australian climate data bank project. Proceedings of the IBPSA Australia 2006 Conference: Investigating the Roles and Challenges of Building Performance Simulation in Achieving a Sustainable Built Environment, The University of Adelaide, Adelaide (2006)
Littler, J.G.F.: Overview of some available models for passive solar design. Comput. Aided Des. 14(1), 15–19 (1982)
Lomas, K.J., Eppel, H.: Sensitivity analysis techniques for building thermal simulation programs. Energy Build. 19(1), 21–44 (1992)
Markus, T.A., Morris, E.N.: Building Climate and Energy. Pitman, London (1980)
Montgomery, D.C., Runger, G.C.: Applied Statistics and Probability for Engineers, 3rd edn. Wiley, New York, NY (2002)
Nielsen, T.R., Duer, K., Svendsen, S.: Energy performance of glazings and windows. Solar Energy. 69(Supplement 6), 137–143 (2001)
Offiong, A., Ukpoho, A.U.: External window shading treatment effects on internal environmental temperature of buildings. Renewable Energy. 29(14), 2153–2165 (2004)
Olgyay, V.: Design With Climate: Bioclimatic Approach to Architectural Regionalism. Princeton University Press, Princeton, NJ (1963)
Omar, E.A., Al-Ragom, F.: On the effect of glazing and code compliance. Appl. Energy. 71(2), 75–86 (2002)
Persson, M.-L., Roos, A., Wall, M.: Influence of window size on the energy balance of low energy houses. Energy Build. 38(3), 181–188 (2006)
Planning: (2006). New 5 Star Requirements: Making Your Home More Energy Efficient. Government of South Australia. Accessed 7 Oct 2006, from http://www.planning.sa.gov.au
Preiser, W.F.E.: Building performance assessment – from POE to BPE, a personal perspective. Archit. Sci. Rev. 48(3), 201–204 (2005)
Preiser, W.F.E., Vischer, J.C.: The evolution of building performance evaluation: an introduction. In: Preiser, W.F.E., Visscher, J.C. (eds.) Assessing Building Performance, pp. 3–13. Elsevier, Oxford, UK (2005)
SOLARCH: Project Homes: House Energy Rating, New South Wales Industry Impact Study (A report prepared for the Sustainable Energy Development Authority): University New South Wales (2000)
Shariah, A., Shalabi, B., Rousan, A., Tashtoush, B.: Effects of absorptance of external surfaces on heating and cooling loads of residential buildings in jordan. Energy Convers. Manage. 39(3–4), 273–284 (1998)
Sowell, E.F., Hittle, D.C.: Evolution of building energy simulation methodology. ASHRAE Trans. 101(P.1), 850–855 (1995)
Sutherland, J.W.: The solution of psychometric problems using a digital computer. Air. Cond. Heating. 25(4), 43–49 (1971)
Szokolay, S.V.: Handbook of Architectural Technology. Van Nostrand Reinhold, New York, NY (1991)
Szokolay, S.V.: Introduction to Architectural Science: The Basis of Sustainable Design. Architectural Press, Oxford (2004)
Tarantola, S., Saltelli, A.: SAMO 2001: methodological advances and innovative applications of sensitivity analysis. Reliab. Eng. Syst. Saf. 79(2), 121–122 (2003)
Tavares, P.F.A.F., Martins, A.M.O.G.: Energy efficient building design using sensitivity analysis – a case study. Energy Build. 39(1), 23–31 (2007)
Thornton, S.B., Nair, S.S., Mistry, S.I.: Sensitivity analysis for building thermal loads. ASHRE Trans. 103, 165–175 (1997)
Tuhus- Dubrow, D., Krarti, M.: Genetic-algorithm based approach to optimize building envelope design for residential buildings. Build Environ. 45(7), 1574–1581 (2010)
Walsh, P.J., Gurr, T.A.: A Comparison of the Thermal Performance of Heavyweight and Lightweight Construction in Australian Dwellings (no. TP44). CSIRO Division of Building Research, Australia (1982)
Williamson, T., Riordan, P.: Thermostat strategies for discretionary heating and cooling of dwellings in temperate climates. Proceeding of 5th IBPSA Building simulation Conference, pp. 1–8. International Building Performance Simulation Association, Prague (1997)
Willrath, H.: Thermal sensitivity of Australian houses to variations in building parameters, 35th Annual Conference of the Australian and New Zealand Solar Energy Society, Canberra (1997)
Zhai, Z.J., Chen, Q.Y.: Sensitivity analysis and application guides for integrated building energy and CFD simulation. Energy Build. 38(9), 1060–1068 (2006)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2011 Springer-Verlag Berlin Heidelberg
About this chapter
Cite this chapter
Kordjamshidi, M. (2011). Modelling Efficient Building Design: Efficiency for Low Energy or No Energy?. In: House Rating Schemes. Green Energy and Technology. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-642-15790-5_4
Download citation
DOI: https://doi.org/10.1007/978-3-642-15790-5_4
Published:
Publisher Name: Springer, Berlin, Heidelberg
Print ISBN: 978-3-642-15789-9
Online ISBN: 978-3-642-15790-5
eBook Packages: EngineeringEngineering (R0)