Advertisement

Additive Manufacturing and Characterization of Architectured Cement-Based Materials via X-ray Micro-computed Tomography

  • Mohamadreza MoiniEmail author
  • Jan Olek
  • Bryan Magee
  • Pablo Zavattieri
  • Jeffrey Youngblood
Conference paper
Part of the RILEM Bookseries book series (RILEM, volume 19)

Abstract

There is an increasing interest in the fabrication of cement-based materials via additive manufacturing (AM) techniques. However, the processing-induced heterogeneities and interfaces represent a major challenge. The role of processing in creating interfaces and their characteristics requires understanding of the microstructure of 3D-printed hardened cement paste (hcp). This work investigates the microstructural features of architectured cement-based materials, including processing-induced heterogeneous patterns, interfacial regions (IRs), and pore network distributions with respect to the architectural patterns. A 3D printer was modified and merged with an extrusion system and specimens were 3D-printed using a layer-wise direct ink writing (DIW) process capable of fabrication of ‘lamellar’ architectures of materials. A lab-based X-ray microscope (XRM) was used to perform X-ray micro-computed tomography (micro-CT) evaluations to explore the microstructural characteristics of 3-day old intact (i.e. not tested) 3D printed and cast specimens at two levels of magnification: 0.4X and 4X. CT scans of printed specimen revealed a patterned pore network and several microstructural features, including: (a) macropores (visible during printing), (b) micropores at interfacial regions (IRs), (c) accumulation of anhydrous cement particles near macropores, and (d) rearrangement of filaments away from their designed toolpath. In comparison, microstructural investigation of cast specimen at 4X scan revealed randomly distributed pores with no connectivity throughout the specimen. The aptitude of micro-CT as a non-destructive technique for microstructural characterization of architectured cement-based materials is discussed. The role of processing to induce and to pattern heterogeneities such as IRs in materials is demonstrated and the role of architecture in controlling such heterogeneities and their directionality through the interface is discussed.

Keywords

3D-printing Cement paste Micro-CT Interfacial Region (IR) 

Notes

Acknowledgements

The authors gratefully acknowledge generous support of this research by the National Science Foundation (CMMI Grant 1562927).

References

  1. 1.
    Gallucci, E., Scrivener, K., Groso, A., Stampanoni, M., Margaritondo, G.: 3D experimental investigation of the microstructure of cement pastes using synchrotron X-ray microtomography (μCT). Cem. Concr. Res. 37(3), 360–368 (2007)CrossRefGoogle Scholar
  2. 2.
    de Wolski, S.C., Bolander, J.E., Landis, E.N.: An in-situ X-ray microtomography study of split cylinder fracture in cement-based materials. Exp. Mech. 54(7), 1227–1235 (2014)CrossRefGoogle Scholar
  3. 3.
    Scrivener, K.L.: Backscattered electron imaging of cementitious microstructures: understanding and quantification. Cem. Concr. Compos. 26(8), 935–945 (2004)CrossRefGoogle Scholar
  4. 4.
    Lu, S., Landis, E.N., Keane, D.T.: X-ray microtomographic studies of pore structure and permeability in Portland cement concrete. Mater. Struct. 39(6), 611–620 (2006)CrossRefGoogle Scholar
  5. 5.
    Diamond, S., Landis, E.: Microstructural features of a mortar as seen by computed microtomography. Mater. Struct. 40(9), 989–993 (2007)CrossRefGoogle Scholar
  6. 6.
    Landis, E.N., Nagy, E.N., Keane, D.T.: Microstructure and fracture in three-dimensions. Eng. Fract. Mech. 70(7–8), 911–925 (2003)CrossRefGoogle Scholar
  7. 7.
    Landis, E.N., Nagy, E.N., Keane, D.T., Nagy, G.: Technique to measure 3D work-of-fracture of concrete in compression. J. Eng. Mech. 125(6), 599–605 (1999)CrossRefGoogle Scholar
  8. 8.
    Landis, E.N., Keane, D.T.: X-ray microtomography for fracture studies in cement-based materials. In: Developments in X-Ray Tomography II, pp. 105–114. International Society for Optics and Photonics (1999)Google Scholar
  9. 9.
    Landis, E.N., Zhang, T., Nagy, E.N., Nagy, G., Franklin, W.R.: Cracking, damage and fracture in four dimensions. Mater. Struct. 40(4), 357–364 (2007)CrossRefGoogle Scholar
  10. 10.
    Sugiyama, T., Promentilla, M.A.B., Hitomi, T., Takeda, N.: Application of synchrotron microtomography for pore structure characterization of deteriorated cementitious materials due to leaching. Cem. Concr. Res. 40(8), 1265–1270 (2010)CrossRefGoogle Scholar
  11. 11.
    Gastaldi, D., Canonico, F., Capelli, L., Boccaleri, E., Milanesio, M., Palin, L., Croce, G., Marone, F., Mader, K.: In situ tomographic investigation on the early hydration behaviors of cementing systems. Constr. Build. Mater. 29, 284–290 (2012)CrossRefGoogle Scholar
  12. 12.
    Lewis, J.A.: Direct ink writing of 3D functional materials. Adv. Funct. Mater. 16(17), 2193–2204 (2006)CrossRefGoogle Scholar
  13. 13.
    Duoss, E.B., Weisgraber, T.H., Hearon, K., Zhu, C., Small, W., Metz, T.R., Vericella, J.J., Barth, H.D., Kuntz, J.D., Maxwell, R.S., Spadaccini, C.M.: Three-dimensional printing of elastomeric, cellular architectures with negative stiffness. Adv. Funct. Mater. 24(31), 4905–4913 (2014)CrossRefGoogle Scholar
  14. 14.
    Raney, J.R., Compton, B.G., Mueller, J., Ober, T.J., Shea, K., Lewis, J.A.: Rotational 3D printing of damage-tolerant composites with programmable mechanics. Proc. Natl. Acad. Sci. 115(6), 1198–1203 (2018)CrossRefGoogle Scholar
  15. 15.
    Aïtcin, P.C., Flatt, R.J. (eds.): Science and Technology of Concrete Admixtures. Woodhead Publishing, Sawston (2015)Google Scholar
  16. 16.
    Rueschhoff, L., Costakis, W., Michie, M., Youngblood, J., Trice, R.: Additive manufacturing of dense ceramic parts via direct ink writing of aqueous alumina suspensions. Int. J. Appl. Ceram. Technol. 13(5), 821–830 (2016)CrossRefGoogle Scholar
  17. 17.
    ASTM C150 – Standard Specification for Portland Cement (2017)Google Scholar
  18. 18.
    ASTM C494 – Standard Specification for Chemical Admixtures for Concrete (2016)Google Scholar
  19. 19.
    Moini M.: Master’s thesis, University of Wisconsin-Milwaukee (2015)Google Scholar
  20. 20.
    Landis, E.N., Keane, D.T.: X-ray microtomography. Mater. Charact. 61(12), 1305–1316 (2010)CrossRefGoogle Scholar
  21. 21.
    Le, T.T., Austin, S.A., Lim, S., Buswell, R.A., Law, R., Gibb, A.G., Thorpe, T.: Hardened properties of high-performance printing concrete. Cem. Concr. Res. 42(3), 558–566 (2012)CrossRefGoogle Scholar
  22. 22.
    Spangenberg, J., Roussel, N., Hattel, J.H., Stang, H., Skocek, J., Geiker, M.R.: Flow induced particle migration in fresh concrete: theoretical frame, numerical simulations and experimental results on model fluids. Cem. Concr. Res. 42(4), 633–641 (2012)CrossRefGoogle Scholar
  23. 23.
    Choi, M., Roussel, N., Kim, Y., Kim, J.: Lubrication layer properties during concrete pumping. Cem. Concr. Res. 45, 69–78 (2013)CrossRefGoogle Scholar
  24. 24.
    Moini, M., Olek, J., Youngblood, J.P., Magee, B., Zavattieri, P.D.: Additive manufacturing and performance of architectured cement-based materials. Adv. Mater. https://doi.org/10.1002/adma.201802123CrossRefGoogle Scholar

Copyright information

© RILEM 2019

Authors and Affiliations

  • Mohamadreza Moini
    • 1
    Email author
  • Jan Olek
    • 1
  • Bryan Magee
    • 2
  • Pablo Zavattieri
    • 1
  • Jeffrey Youngblood
    • 1
  1. 1.Purdue UniversityWest LafayetteUSA
  2. 2.Ulster UniversityNewtownabbeyUK

Personalised recommendations