Abstract
The subject of the paper is the concept of a measurement system of selected operating parameters of the overhead travelling crane bridge structure and the roadway crane girder beams for the purpose of identifying the operating conditions of the device in practice (under operation). The subject measurement system uses vibration sensors located at specific locations of the crane bridge structure and selected cross-sections of the device roadway. The obtained from measurements results will then be used in the process of monitoring the process of device operation. The paper focuses on the measurement system hardware architecture and software (called application). The essence of the measurement system is the possibility of wireless transmission of results obtained from measurements for the purposes of their analysis and presentation, and then decision processes for the needs of controls. In this sense, the paper is undertaken very important device exploitation parameters sensing issue which is a part of transport telematics problems. The practical aspect of operation of the discussed measuring system was tested with a positive results on a physical model of a laboratory bridge crane with a lifting capacity of 150 kg.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Szpytko, J.: Kształtowanie procesu eksploatacji środków transportu bliskiego, Instytut Technologii Eksploatacji, Kraków-Radom (2004)
Szpytko, J.: Zintegrowany system nadzorowania wybranych parametrów eksploatacyjnych wielkogabarytowych szynowych urządzeń transportowych na przykładzie zautomatyzowanej suwnicy pomostowej, nr 46, Uczelniane Wydawnictwa Naukowe Dydaktyczne AGH, Kraków (1996)
Kocerba, A., Szpytko, J.: Monitoring methods of operation surrounding of transport device. J. KONES: Powertain Transp. 15(4), 235–243 (2008)
Smoczek, J., Szpytko, J.: Particle swarm optimization-based multivariable generalized predictive control for an overhead crane. IEEE-ASME Trans. Mechatron. 24(3), 299–308 (2017)
Smoczek, J., Szpytko, J.: Comparision of model predictive, input shaping and feedback control for a lab-scaled overhead crane. In: 21st International Conference on Methods and Models in Automation and Robotics (MMAR), Międzyzdroje, Poland, 29 August–01 September, pp. 288–293 (2016)
Adamczyk, J., Bednarz, J., Targosz, J.: Monitorowanie wpływu drgań od pojazdów szynowych na konstrukcje inżynierskie, Autobusy. Technika, Eksploatacja, Systemy Transportowe, nr 3, tom 14, str. 1709–1716 (2013)
Bednarz, J., Targosz, J.: Analysis of civil engineering structures vibroisolation effectiveness. J. KONES Powertrain Transp. 19(4), 33–41 (2012)
Przysowa, R., Tuzik, A.: Data management techniques for blade vibration analysis. J. KONBiN 1(37), 95–132 (2016)
Żółtowski, B., Łukasiewicz, M.: Diagnostyka drganiowa maszyn, Bydgoszcz – Radom, Wydawnictwo Naukowe Instytutu Technologii Eksploatacji (2012)
Hyla, P., Szpytko, J.: Vision method for rope angle swing measurement for overhead travelling cranes – validation approach. In: Mikulski, J. (ed.) TST 2013. CCIS, vol. 395, pp. 370–377. Springer, Heidelberg (2013). https://doi.org/10.1007/978-3-642-41647-7_45
Hyla, P., Szpytko, J.: Crane payload position measurement vision-based system dedicated for anti-sway solutions. In: Mikulski, J. (ed.) TST 2014. CCIS, vol. 471, pp. 404–413. Springer, Heidelberg (2014). https://doi.org/10.1007/978-3-662-45317-9_43
Szpytko, J., et al.: Selected measurement and control techniques: experimental verification on a lab-scaled overhead crane. J. KONES 24(3), 299–308 (2017)
EN 13001–1:2009. Cranes. General Design. Part 1: General Principles and Requirements
EN 13001–2:2009. Cranes. General Design. Part 2: Load Actions
EN 13001–3.1: 2009. Cranes. General Design. Part 3-1: Limit States and Proof of Competence of Steel Structure
Chruściel, M.: LabVIEW w praktyce. Wydawnictwo BTC, Legionowo (2008)
Sorensen, K., et al.: A multi-operational-mode anti-sway and positioning control for an industrial bridge crane. In: Proceedings of the 17th World Congress of IFAC, Seoul, Korea, 6–11 July, pp. 881–888 (2008)
Chen Chih Peng, K., Singhose, W., Bhaumik, P.: Using machine vision and hand-motion control to improve crane operator performance. Trans. Syst. Man Cybern. Part A: Syst. Hum. 42(6), 1496–1503 (2012)
Nara, S., et al.: Visual feedback tracking of crane hook. In: Proceedings of the International Conference on Intelligent Robots and Systems, Beijing, China, pp. 2736–2742 (2006)
Acknowledgement
The work has been financially supported by the Polish Ministry of Science and Higher Education in the year 2018.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer Nature Switzerland AG
About this paper
Cite this paper
Hyla, P., Szpytko, J. (2018). Telematics for the Purpose of Identifying the Conditions of Use of a Bridge Crane. In: Mikulski, J. (eds) Management Perspective for Transport Telematics. TST 2018. Communications in Computer and Information Science, vol 897. Springer, Cham. https://doi.org/10.1007/978-3-319-97955-7_32
Download citation
DOI: https://doi.org/10.1007/978-3-319-97955-7_32
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-97954-0
Online ISBN: 978-3-319-97955-7
eBook Packages: Computer ScienceComputer Science (R0)