Abstract
Micro- and nanoscale welding or joining processes are needed in miniaturisation or microsystem fabrication such as microelectromechanical systems (MEMS) and carbon nanotubes (CNTs). The constant strive for miniaturisation that necessitates that products are manufactured smaller and more lighter comes with the challenge of having smaller parts that require to be joined or assembled at a micro- or nanoscale level. The ability to weld at micro- and nanoscale levels is key to the efficient and effective fabrication of miniaturised components and products. This need has necessitated the development of welding processes that have the capability to join these delicate and fragile parts. The conventional joining process could cause heat damage to the welded part because of the large input from such processes. Also, the tools of these conventional welding processes may even be larger than the miniaturised parts that makes them unsuitable in fabrication of parts at micro- and nanoscale levels. Micro- and nanowelding are performed under powerful microscope. In this chapter, non-contact micro- and nanowelding processes are discussed. Two types of these advanced welding processes discussed are the advanced non-contact fusion welding and solid-state welding processes. Laser micro/nanowelding and electron beam micro/nanowelding are the two fusion-state micro/nanowelding processes that are presented in this chapter. For the solid-state micro/nanowelding processes, ultrasonic micro/nanowelding and resistant micro/nanowelding are presented. In micro- and nanowelding processes, the main challenge is the tight operational tolerance that needs to be met and the processing parameters are found to play an important role in achieving the desired results. The focus of this chapter is on the research developments in this field. The working principles, advantages, limitations and areas of application of these welding processes are explained in Chaps. 7 and 8.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
H. El Kadiri, Y. Bienvenu, K. Solanki, M.F. Horstemeyer, P.T. Wang, Creep and tensile behaviors of Fe–Cr–Al foils and laser microwelds at high temperature. Mater. Sci. Eng. A 421, 168–181 (2006)
X. Chen, D. Brox, B. Assadsangabi, M. Sultan Mohamed Ali, K. Takahata, A stainless-steel-based implantable pressure sensor chip and its integration by microwelding. Sens. Actuators A 257, 134–144 (2017)
A. Ascari, A. Fortunato, G. Guerrini, E. Liverani, A. Lutey, Long pulse laser micro welding of commercially pure titanium thin sheets. Procedia Eng. 184, 274–283 (2017)
B.-C. Kim, T.-H. Kim, J.-S. Kim, K.-B. Kim, H.-Y. Lee, Investigation on the effect of laser pulse shape during Nd:YAG laser microwelding of thin al sheet by numerical simulation. Metall. Mater. Trans. A 33a, 1449 (2002)
G.S. Zou, Y.D. Huang, A. Pequegnat, X.G. Li, M.I. Khan, Y. Zhou, Crossed-wire laser microwelding of Pt-10 Pct Ir to 316 low-carbon vacuum melted stainless steel: part I. Mechanism of joint formation. Metall. Mater. Trans. A 43a, 1223 (2012)
Y.D. Huang, A. Pequegnat, G.S. Zou, J.C. Feng, M.I. Khan, Y. Zhou, Crossed-wire laser microwelding of Pt-10 Pct Ir to 316 Lvm stainless steel: part Ii. Effect of orientation on joining mechanism. Metall. Mater. Trans. A 43a, 1234 (2012)
W.-S. Chang, S.-J. Na, A study on heat source equations for the prediction of weld shape and thermal deformation in laser microwelding. Metall. Mater. Trans. B. 33a, 757 (2002)
W. Shi, J. Huang, Y. Xie, Y. Li, F. An, Laser micro-welding technology for Cu–Al dissimilar metals and mechanisms of weld defect formation. Int. J. Adv. Manuf. Technol. 93, 4197–4201 (2017)
H.-T. Liao, Z.-W. Chen, A study on fiber laser micro-spot welding of thin stainless steel using response surface methodology and simulated annealing approach. Int. J. Adv. Manuf. Technol. 67, 1015–1025 (2013)
M. Rohde, C. Markert, W. Pfleging, Laser micro-welding of aluminium alloys: experimental studies and numerical modelling. Int. J. Adv. Manuf. Technol. 50, 207–215 (2010)
Y. Yuan, J. Chen, Nano-welding of multi-walled carbon nanotubes on silicon and silica surface by laser irradiation. Nanomaterials 6, 36 (2016). https://doi.org/10.3390/nano6030036
B. Mehlmann, E. Gehlen, A. Olowinsky, A. Gillner, Laser micro welding for ribbon bonding. Phys. Procedia 56, 776–781 (2014)
T. Ussing, L.V. Petersen, C.B. Nielsen, B. Helbo, L. Højslet, Micro laser welding of polymer microstructures using low power laser diodes. Int. J. Adv. Manuf. Technol. 33, 198–205 (2007)
A. Patschger, J. Bliedtner, J.P. Bergmann, Approaches to increase process efficiency in laser micro welding. Phys. Procedia 41, 592–602 (2013)
P. Dong, H. Li, W. Wang, J. Zhou, Microstructural characterization of laser micro-welded Nitinol wires. Mater. Charact. 135, 40–45 (2018)
H. Mostaan, M. Shamanian, S. Hasani, M. Safari, J.A. Szpunar, Nd:Yag laser micro-welding of ultra-thin Feco−V magnetic alloy: Optimization of weld strength. Trans. Nonferrous Met. Soc. China 27, 1735–1746 (2017)
A. Hozoorbakhsh, M.I.S. Ismail, N.B.A. Aziz, A computational analysis of heat transfer and fluid flow in high-speed scanning of laser micro-welding. Int. Commun. Heat Mass Transfer 68, 178–187 (2015)
M. Baruah, S. Bag, Influence of pulsation in thermo-mechanical analysis on laser microwelding of Ti6Al4V alloy. Opt. Laser Technol. 90, 40–51 (2017)
C. Yuhua, M. Yuqing, L. Weiwei, H. Peng, Investigation of welding crack in micro laser welded NiTiNb shape memory alloy and Ti6Al4V alloy dissimilar metals joints. Opt. Laser Technol. 91, 197–202 (2017)
U. Reisgen, T. Dorfmuller, Developments in micro-electron beam welding. Microsyst. Technol. 14, 1871–1877 (2008)
U. Dilthey, T. Dorfmuller, Micro electron beam welding. Microsyst. Technol. 12, 626–631 (2006)
Q. Yang, S. Bai, G. Wang, J. Bai, Local reconstruction and controllable nanospot welding of multiwalled carbon nanotubes under mild electron beam irradiation. Mater. Lett. 60, 2433–2437 (2006)
G. Smolka, A. Gillner, L. Bosse, R. Lützeler, Micro electron beam welding and laser machining—Potentials of beam welding methods in the micro-system technology. Microsyst. Technol. 10, 187–192 (2004)
W.X. Chan, S.H. Ng, K.H.H. Li, W.-T. Park, Y.-J. Yoon, Micro-ultrasonic welding using thermoplastic-elastomeric compositefilm. J. Mater. Process. Technol. 236, 183–188 (2016)
X. Sánchez-Sánchez, M. Hernández-Avila, L.E. Elizalde, O. MartÃnez, I. Ferrer, A. ElÃas-Zuñiga, Micro injection molding processing of UHMWPE using ultrasonic vibration energy. Mater. Design 132, 1–12 (2017)
B. Zhao, Y. Wang, Y. Zhan, Decrease of contact resistance at the interface of carbon nanotube/electrode by nanowelding. Electron. Mater. Lett. 13(2), 168–173 (2017)
K. Mistewicz, M. Nowak, R. Wrzalik, J. Śleziona, J. Wieczorek, A. Guiseppi-Elie, Ultrasonic processing of SbSI nanowires for their application to gas sensors. Ultrasonics 69, 67–73 (2016)
B. Zhao, Y. Wang, C. Liu, L. Zhang, X. Liu, Y. Zhang, Ultrasonic nano welding of SiC microparticles on Al surface. Appl. Surf. Sci. 258, 5786–5789 (2012)
B. Zhao, C. Chen, B. Yadian, P. Liu, Z. Li, X. Dong, Y. Zhang, Effects of welding head on the carbon nanotube field emission in ultrasonic nano welding. Thin Solid Films 517, 2012–2015 (2009)
B. Zhao, G. Jiang, H. Qi, Joining aluminum sheets with conductive ceramic films by ultrasonic nano welding. Ceram. Int. 42, 8098–8101 (2016)
Z. Chen, Joint formation mechanism and strength in resistance microwelding of 316L stainless steel to Pt wire. J. Mater. Sci. 42, 5756–5765 (2007)
S. Fukumoto, Y. Zhou, Mechanism of resistance microwelding of crossed fine nickel wires. Metall. Mater. Trans. A 35, 3165 (2004)
S. Fukumoto, Z. Chen, Y. Zhou, Interfacial phenomena and joint strength in resistance microwelding of crossed Au-plated Ni wires. Metall. Mater. Trans. A 36, 2717 (2005)
M.I. Khan, J.M. Kim, M.L. Kuntz, Y. Zhou, Bonding mechanisms in resistance microwelding of 316 low-carbon vacuum melted stainless steel wires. Metall. Mater. Trans. A 40A, 910–919 (2009)
B. Tam, A. Pequegnat, M.I. Khan, Y. Zhou, Resistance microwelding of Ti-55.8 wt pct Ni Nitinol wires and the effects of pseudoelasticity. Metall. Mater. Trans. A 43, 2969–2978 (2012)
R.M. Mahamood, E.T. Akinlabi, in Chapter 21 - Laser-assisted additive fabrication of micro-sized coatings. Woodhead Publishing Series in Welding and Other Joining Technologies, Advances in Laser Materials Processing, ed by J. Lawrence, Second Edition (Woodhead Publishing, Cambridge, 2018), pp. 635–664
G. Zhao, Z. Wei, J. Du, W. Liu, X. Wang, Y. Yao, Additive manufacturing of Sn63Pb37 component by micro-coating. Procedia Eng. 157, 193–199 (2016)
R.M. Mahamood, E.T. Akinlabi, M. Shukla, S. Pityana, Revolutionary additive manufacturing: An overview. Laser Eng. 27, 161–178 (2014)
R.M. Mahamood, E.T. Akinlabi, M. Shukla, S. Pityana, Material efficiency of laser metal deposited Ti6Al4V: Effect of laser power. Eng. Lett. 21(1), EL_21_1_03 (2013.) http://www.engineeringletters.com/issues_v21/issue_1/EL_21_1_03.pdf
R.M. Mahamood, E.T. Akinlabi, Process parameters optimization for material deposition efficiency in laser metal deposited titanium alloy. Lasers Manuf. Mater. Process. 3(1), 9–21 (2016). https://doi.org/10.1007/s40516-015-0020-5
R.M. Mahamood, E.T. Akinlabi, S.A. Akinlabi, Laser power and scanning speed influence on the mechanical property of laser metal deposited titanium-alloy. Lasers Manuf. Mater. Process. 2(1), 43–55 (2015)
S. Pityana, R.M. Mahamood, E.T. Akinlabi, M. Shukla, Effect of gas flow rate and powder flow rate on properties of laser metal deposited Ti6Al4V. 2013 International Multi-conference of Engineering and Computer Science (IMECS 2013), 2013, pp. 848–851
R.M. Mahamood, E.T. Akinlabi, Effect of processing parameters on wear resistance property of laser material deposited titanium-alloy composite. J. Optoelectron. Adv. Mater. 17(9–10), 1348–1360 (2015)
R.M. Mahamood, E.T. Akinlabi, Effect of laser power on surface finish during laser metal deposition process. WCECS 2, 965–969 (2014)
M. Shukla, R.M. Mahamood, E.T. Akinlabi, S. Pityana, Effect of laser power and powder flow rate on properties of laser metal deposited Ti6Al4V. World Acad. Sci. Technol. 6, 44–48 (2012)
R.M. Mahamood, E.T. Akinlabi, M.G. Gbadebo, Laser metal deposition process for product remanufacturing, In Advanced Manufacturing Technologies Modern Machining, Advanced Joining, Sustainable Manufacturing, ed. by G. Kapil (Springer, Cham, 2017). pp. 267–291
R.M. Mahamood, E.T. Akinlabi, M. Shukla, S. Pityana, Scanning velocity influence on microstructure, microhardness and wear resistance performance on laser deposited Ti6Al4V/TiC composite. Mater. Des. 50, 656–666 (2013)
M.R. Mahamood, Laser Metal Deposition Process of Metals, Alloys, and Composite Materials (Springer, Cham, 2017)
M.R. Mahamood, E.T. Akinlabi, Functionally Graded Materials (Springer Science Publisher, Cham, 2017)
R.M. Mahamood, E.T. Akinlabi, Achieving mass customization through additive manufacturing, in Advances in Ergonomics of Manufacturing: Managing the Enterprise of the Future, ed. by C. Schlick, S. Trzcieliński, (Springer International Publishing, Cham, 2016), pp. 385–390
M. Vaezi, H. Seitz, S. Yang, A review on 3D micro-additive manufacturing technologies. Int. J. Adv. Manuf. Technol. 67, 1721–1754 (2013)
M. Attaran, The rise of 3-D printing: The advantages of additive manufacturing over traditional manufacturing. Business Horizons 60(5), 677–688 (2017)
S. Singh, S. Ramakrishna, Biomedical applications of additive manufacturing: Present and future. Curr. Opin. Biomed. Eng. 2, 105–115 (2017)
S. Bose, D. Ke, H. Sahasrabudhe, A. Bandyopadhyay, Additive manufacturing of biomaterials. Prog. Mater. Sci. 93, 45–111 (2018)
E. T. Akinlabi, M. R. Mahamood, S. A. Akinlabi (eds.), Advanced Manufacturing Using Laser Material Processing (IGI Global, Hershey, PA, 2016)
R.M. Mahamood, E.T. Akinlabi, Laser additive manufacturing, in Advanced Manufacturing Using Laser Material Processing, ed. by E. T. Akinlabi, M. R. Mahamood, S. A. Akinlabi, (IGI Global, Hershey, PA, 2016), pp. 1–23
R.M. Mahamood, Laser metal deposition process, in Advanced Manufacturing Using Laser Material Processing, ed. by E. T. Akinlabi, M. R. Mahamood, S. A. Akinlabi, (IGI Global, Hershey, PA, 2016), pp. 46–59
Acknowledgments
This work was supported by the University of Johannesburg research council (URC) fund and University of Ilorin.
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer International Publishing AG
About this chapter
Cite this chapter
Mahamood, R.M., Akinlabi, E.T. (2018). Non-contact Micro- and Nanowelding. In: Advanced Noncontact Cutting and Joining Technologies. Mechanical Engineering Series. Springer, Cham. https://doi.org/10.1007/978-3-319-75118-4_9
Download citation
DOI: https://doi.org/10.1007/978-3-319-75118-4_9
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-75117-7
Online ISBN: 978-3-319-75118-4
eBook Packages: EngineeringEngineering (R0)