Abstract
As the load demands on highway bridges increases, it is essential that the load rating procedures reliably assess the condition of existing structures. In addition, conventional design office load rating techniques cannot be used for bridges without structural plans, which indicates the need for a more advanced load rating procedure. This paper presents a methodology to compute the live load-carrying capacity of reinforced concrete T-beam bridges, which can be applied for bridges with structural plans or with missing or limited design information. The method involves modal identification of bridge using ambient vibrations and finite element model updating using vibration characteristics for capacity estimation. A simply supported T-beam bridge located in Virginia is selected for field-testing to verify the proposed method. The bridge is composed of five spans of the same length, 12.95 m for each, with a total length of 65.4 m and a width of 8.864 m. A total of nine accelerometers are installed to bridge to collect acceleration data for 15 min at a sampling rate of 500 Hz. The modal properties of the bridge are determined using enhanced frequency domain decomposition technique. The initial finite element model of the bridge is updated such that the modal properties of the bridge match the field measured parameters. The load effects and capacity of the bridge are determined and used to calculate the load rating factor. The rating factors obtained from the proposed method and traditional design office load rating procedures are compared. The results indicate that the proposed method can reveal the reserve capacity of bridges.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Brownjohn, J.M., Moyo, P., Omenzetter, P., Lu, Y.: Assessment of highway bridge upgrading by dynamic testing and finite-element model updating. J. Bridg. Eng. 8(3), 162–172 (2003)
Wang, L., Chan, T.H.: Review of vibration-based damage detection and condition assessment of bridge structures using structural health monitoring. In: QUT Conference Proceedings (2009)
Lee, J.J., Yun, C.B.: Damage diagnosis of steel girder bridges using ambient vibration data. Eng. Struct. 28(6), 912–925 (2006)
Gheitasi, A., Ozbulut, O.E., Usmani, S., Alipour, M., Harris, D.K.: Experimental and analytical vibration serviceability assessment of an in-service pedestrian bridge. Case Stud. Nondestruct. Test. Eval. 6, 79–88 (2016)
Gul, M., Catbas, F.N.: Damage assessment with ambient vibration data using a novel time series analysis methodology. J. Struct. Eng. 137(12), 1518–1526 (2010)
AASHTO: The Manual for Bridge Evaluation. American Association of State Highway and Transportation Officials, Washington, DC (2011)
Alipour, M., Harris, D.K., Ozbulut, O.E.: Vibration testing for bridge load rating. In: Dynamics of Civil Structures, vol. 2, pp. 175–184. Springer International Publishing, New York (2016)
Brincker, R., Ventura, C., Andersen, P.: Damping estimation by frequency domain decomposition. In: 19th International Modal Analysis Conference (2001)
Shafiei Dizaji, M., Alipour, M., Harris, D.: Leveraging vision for structural identification – a digital image correlation based approach. In: International Digital Image Correlation Society Conference (iDICs), SEM Fall Conference, Philadelphia, PA, USA (8–11 Nov 2016)
Shafiei Dizaji, M., Harris, D., Alipour, M., Ozbulut, O.: En“vision”ing a novel approach for structural health monitoring – a model for full-field structural identification using 3D–digital image correlation. In: The 8th International Conference on Structural Health Monitoring of Intelligent Infrastructure, Bridbane, Australia (5–8 Dec 2017)
Acknowledgements
This material is based upon the work supported by the Virginia Department of Transportation. The authors would like to thank Dr. Bernard L. Kassner of Virginia Transportation Research Council for his helps in conducting the vibration testing of the bridge.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 The Society for Experimental Mechanics, Inc.
About this paper
Cite this paper
Ndong, A.K., Dizaji, M.S., Alipour, M., Ozbulut, O.E., Harris, D.K. (2019). Load Rating of a Reinforced Concrete T-Beam Bridge Through Ambient Vibration Testing and Finite Element Model Updating. In: Pakzad, S. (eds) Dynamics of Civil Structures, Volume 2. Conference Proceedings of the Society for Experimental Mechanics Series. Springer, Cham. https://doi.org/10.1007/978-3-319-74421-6_45
Download citation
DOI: https://doi.org/10.1007/978-3-319-74421-6_45
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-74420-9
Online ISBN: 978-3-319-74421-6
eBook Packages: EngineeringEngineering (R0)