Abstract
The Chapter “Low-Pressure Cold Spray” presents a description of basics of LPCS technology, bonding mechanisms, temperature effects and LPCS localization processes. To illustrate the main aspects of LPCS system parameters determination, the numerical simulation and experimental data are presented. The emphasis is placed on the proper development of the cold-sprayed metal matrix composite coatings and their structure and properties, which are of paramount importance to the success of LPCS. Processes such as bonding, hardening and softening of the coating materials during cold spraying and coating structure formation at following heat treatment (sintering) are dealt with from the theoretical as well as practical aspect.
Applications of LPCS technology occur for the cases where conventional thermal spraying technologies cannot be successfully used. The analysis of various components repair is presented in which the methodology and accompanying technical data for the transition of cold spray technology into the industry, and several case studies are presented. The case studies show the tremendous impact that LPCS has made for a few select applications, representing steels, magnesium, aluminium and composite materials, while attempting to include as much technical data substantiating the advantages and benefits gained by transition of the process.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Ahmad Z (2006) Principles of corrosion engineering and corrosion control. Butterworth-Heinemann, p 187
Alkhimov AP, Gudilov AI, Kosarev VF, Nesterovich NI (2000) Specific features of microparticle deformation upon impact on a rigid barrier. J Appl Mech Tech Phys 41(1):188–192
ASM Handbook (2003) Corrosion: fundamentals, testing, and protection, vol 13A. ASM International, New York, pp 1779–1793
Assadi H, Gartner F, Stoltenhoff T, Kreye H (2003) Bonding mechanism in cold spraying. Acta Mater 51:4379–4394
Assadi H, Kreye H, Gartner F, Klassen T (2016) Cold spraying – a materials perspective. Acta Mater 116:382–407
Baker MA, Gissler W, Klose S, Trampert M, Weber F (2000) Morphologies and corrosion properties of PVD Zn-Al coatings. Surf Coat Technol 125:207
Balaji D, Maridurai T (2016) Experimental investigation on engine performance and emission in diesel engine by aluminum-titanium thermal barrier coating. Int J Chem Sci 14(1):152–160
Boag A, Taylor RJ, Muster TH, Goodman N, Hughes AE (2010) Stable pit formation on AA2024-T3 in a NaCl environment. Corros Sci 52(1):90–103
Boag A, Hughes AE, Glenn AM, Muster TN (2011) Corrosion of AA2024-T3 part I. Localized corrosion of isolated IM particles. Corros Sci 53(1):17–26
Bobzin K, Öte M, Königstein T (2017) Investigation of amorphous/nanocrystalline iron-based thermal barrier coatings. J Therm Spray Tech. https://doi.org/10.1007/s11666-016-0520-7
Barbezat G (2006) Application of thermal spraying in the automobile industry. Surf Coat Technol 201:2028–2031
Champagne VK (2007) The cold spray materials deposition process: fundamentals and applications. Woodhead Publishing Limited, Cambridge, pp 230–312
Champagne V, Helfritch D (2015) Critical assessment 11: structural repairs by cold spray. Mater Sci Technol 31(6):627–634
Chang BY, Park SM (2010) Electrochemical impedance spectroscopy. Annu Rev Anal Chem 3:207–229
Covac C, Alaux TJ, Marrow E, Covekar A, Legat M (2010) Correlations of electrochemical noise, acoustic emission and complementary monitoring techniques during intergranular stress-corrosion cracking of austenitic stainless steel. Corros Sci 52(6):2015–2025
Davis JR (ed) (2004) Handbook of thermal spray technology. ASM International, Ohio, pp 220–225
DeForce B, Eden T, Potter J, Champagne V, Leyman P, Helfritch D (2007) Application of aluminum coatings for the corrosion protection of magnesium by cold spray. Proceedings of TRI service corrosion conference, Denver, USA
Dzhurinskiy D, Maeva E, Ev L, Maev RG (2012) Corrosion protection of light alloys using low pressure cold spray. J Therm Spray Tech 2(12):304–313
Eakins DE Thadhani NN (2006) Instrumented Taylor anvil-on-rod impact tests for validating applicability of standard strength models to transient deformation states, J Appl Phys 100:073503: doi: https://doi.org/10.1063/1.2354326
Estrin Y, Toth LS, Molinari A, Brechet Y (1998) A dislocation based model for all hardenibg stages in large strain deformation. Acta Mater 46(15):5509–5522
Fenker M, Balzer M, Kappl H (2014) Corrosion protection with hard coatings on steel: past approaches and current research efforts. Surf Coat Technol 257:182–205
Gray JE, Luan B (2002) Protective coatings on magnesium and its alloys — a critical review. J Alloys Compd 336(1–2):88–113
Grujicic M, Zhao CL, DeRosset WS, Helfritch D (2004) Adiabatic shear instability based mechanism for particles/substrate bonding in the cold-gas dynamic-spray process. Mater Des 25:681–688
Guillaumin V, Mankowski G (1999) Corrosion protection with aluminum coatings on steel. Corros Sci 41:421–438
Gust WH (1982) High impact deformation of metal cylinders at elevated temperatures. J Appl Phys 53(5):3566–3575
Guzman MA, Gissler W, Klose S, De Rossi S (2000) Vapour deposited Zn-Cr alloy coatings for enhanced manufacturing and corrosion resistance of steel sheets. Surf Coat Technol 125:218–227
Harach DJ, Vecchio KS (2001) Microstructure evolution in metal-intermetallic laminate (MIL) composites synthesized by reactive foil sintering in air. Metall Mater Trans A 32A:1493–1505
Heinz A, Haszler A, Keidel C, Bendictus R, Mille WS (2000) Recent development in aluminium alloys for aerospace applications. Mater Sci Eng 280(1):102–107
Holmberg K, Matthews A. (2009) Coatings tribology: properties, mechanisms, techniques and applications in surface engineering. Elsevier tribology and interface engineering series no. 56.2nd ed. Amsterdam, The Netherlands: Elsevier
Holmberg K, Laukkanen A, Ghabchi A, Rombouts M, Turunen E, Waudby R, Suhonen T, Valtonen K, Sarlin E (2014) Computational modelling based wear resistance analysis of thick composite coatings. Tribol Int 72:13–30
Hong T, Nagumo M (1997) Effect of surface roughness on early stages of pitting corrosion of type 301 stainless steel. Corros Sci 39:665
Hu N, Molinari JF (2004) Shear bands in dense metallic granular materials. J Mech Phys Solids 52:499–531
Hughes AE, Boag A, Glenn AM, Muster TN, Ryan C, Luo C, Thompson GE (2011) Corrosion of AA2024-T3 part II co-operative corrosion. Corros Sci 53(1):27–39
Hussain T, McCartney DG, Shipway PH, Zhang D (2009) Bonding mechanisms in cold spraying: the contributions of metallurgical and mechanical components. J Therm Spray Technol 18(3):364–379
Hwang IJ, Hwang DY, Kim YM, Yoo B, Shin DH (2010) Formation of uniform passive oxide layers on high Si content Al alloy by plasma electrolytic oxidation. Alloys J Compd 504:527–530
Jalilvand V, Omidvar H, Shakeri HR, Rahimipour MR (2013) Microstructural evolution during transient liquid phase bonding of Inconel 738LC using AMS 4777 filler alloy. Mater Charact 75:20–28
Jindal V, Srivastava VC, Das A, Ghosh RN (2006) Reactive diffusion in the roll bonded iron–aluminum system. Mater Lett 60:1758–1761
Klinkov SV, Kosarev VF, Rein M (2005) Cold spray deposition: significance of particle impact phenomena. Aerosp Sci Technol 9(7):582–591
Koivuluoto H, Lagerbom J, Kylmalahti M, Vuoristo P (2008) Microstructure and mechanical properties of low-pressure cold-sprayed (LPCS) coatings. J Therm Spray Technol 17(5–6):721–727
Lee H, Jung SH, Lee SY, Ho Y, Kyung Y, Ko H (2005) Fundamental study of cold gas dynamic spray process. Appl Surf Sci 252:1891–1898
Li W, Li DY (2006) Influence of surface morphology on corrosion and electronic behavior. Acta Mater 54:445–452
Li H, Li X, Sun M, Wang H, Huang G (2010) Corrosion resistance of cold-sprayed Zn-50Al coatings in seawater. J Chin Soc Corros Prot 30:62–66
Li Q, Lu H, Cui J, Kuma V, An M, Li DY (2017) Produce mirror-shining surface of electrogalvanized steel with significantly elevated scratch resistance through combined nanoelectrodeposition and passivation treatment. Wear 376-377:1707–1712
Ls-Dyna keyword user’s manual (2013) Vol I. LSTC
Luo J-G, Acoff VL (2004) Using cold roll bonding and annealing to process Ti/al multi-layered composites from elemental foils. Mater Sci Eng A Struct Mater 379(1–2):164–172
Maev RG, Leshchynsky V (2007) Introduction to low pressure gas dynamic spray. John Willey and Son – VCH, Manheim, p 207
Maev RG, Leshchynsky V (2015) Cold gas dynamic spray. CRC Press, Boca Raton, 334p
Maev R Gr, Leshchinsky E, Maeva E (2011) New cold spray based technique of FeAl intermetallic compound coating synthesis. In: Proceeding of ITSC 2011 Conference, Hamburg, Germany
Maev R Gr, Leshchynsky V, Strumban E., Ziganshin D., Belenkov R., Dzhurinskiy D. (2017) Apparatus and method for cold spray coating processing. US Patent Application, US2017/0121825
Maitra S, English GC (1981) Mechanism of localized corrosion of 7075 alloy plate. Metall Trans A 12:535
Massalski TB (1986) Binary alloy phase diagrams. ASM International, Metals Park, p 112
Molinari A (1997) Collective behaviour and spacing of adiabatic shear bands. J Mech Phys Solids 45(9):1551–1575
Motzet H, Pollmann H (1999) Synthesis and characterization of sulfite-containing AFM phases in the system CaO-Al2O3-SO2-H2O. Cem Concr Res 29:1005–1011
Nakai M, Rto T (2000) New aspect of development of high strength aluminum alloys for aerospace applications. Mater Sci Eng 285(1–2):62–68
Nie JF (2014) Physical metallurgy of light alloys. Elsevier, Physical Mettalurgy, pp 2009–2156
Orazem ME, Pebere N, Tribollet B (2006) Enhanced graphical representation of electrochemical impedance data. J Electrochem Soc 153(4):B129–B136
Papyrin A (2001) Cold spray technology. Adv Mater Process 159(9):49–51
Papyrin A, Kosarev V, Klinkov S, Alkhimov A (2006) Cold spray technology. Elsevier, London pp 125–210
Pawlowski L (2008) The science and engineering of thermal spray coatings. John Wiley & Sons, England, pp 220–590
Pourbaix M (1975) Atlas of electrochemical equilibria in aqueous solutions. NACE, Houston
Rojas PN, Rodil SE (2012) Corrosion behaviour of amorphous niobium oxide coatings. Int J Electrochem Sci 7:1443–1458
Sasaki GT, Burstein G (1996) The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential. Corros Sci 38:2111–2124
Schmidt T, Gartner F, Kreye H (2006) New developments in cold spray based on higher gas and particle temperatures. Therm Spray Technol 15:488–494
Schmitt G, Schütze M, Hays G (2009) Global needs for knowledge dissemination, research and development in materials deterioration and corrosion control. World Corrosion Organization (WCO), New York
Shin D-II, Gitzhofer F, Moreau C (2007) Thermal property evolution of metal based thermal barrier coatings with heat treatments. J Mater Sci 42:5915–5923
Smulko JM, Darowicki K, Zieliñski A (2007) On electrochemical noise analysis for monitoring of uniform corrosion rate. IEEE Trans Instrum Meas 56(5):2018–2023
Spencer K, Fabijanic DM, Zhang M-X (2009) The use of al–Al2O3 cold spray coatings to improve the surface properties of magnesium alloys. Surf Coat Technol 204:336–344
Steinhauser S, Wielage B (1997) Composite coatings: manufacture, properties, and applications. Surf Eng 13(4):289–294
Straffelini G, Pellizzari M, Molinari A (2004) Influence of load and temperature on the dry sliding behaviour of Al-based metal-matrix-composites against friction material. Wear 256(7-8):754–763
Stoltenhoff T, Kreye H, Richter HJ (2002) An analysis of the cold spray process and its coatings. J Therm Spray Technol 11(4):542–550
Tian W, Wang Y, Zhang T, Yang Y (2009) Sliding wear and electrochemical corrosion behavior of plasma sprayed nanocomposite Al2O3-13%TiO2 coatings. Mater Chem Phys 118:37–45
Takahashi H, Sakairi M, Kikuchi T (2010) Three-dimensional microstructure fabrication with aluminum anodizing, laser irradiation, and electrodeposition. Mod Asp Electrochem 46:59–174
Tao Y, Xiong T, Sun C, Kong L, Cui X, Li T (2010) Microstructure and corrosion performance of a cold sprayed aluminium coating on AZ91D magnesium alloy. Corros Sci 52:3191–3197
Terada Y, Ohkubo K, Nakagawa K, Mohri T, Suzuki T (1995) Thermal conductivity of B-2 aluminides and titanides. Intermetallics 3:347–355
Van Steenkiste TH, Smith JR, Teets RE, Moleski JJ, Gorkiewicz DW, Tison RP, Marantz DR, Kowalsky KA, Riggs WL, Zajchowski PH, Pilsner B, McCune RC, Barnett KJ (1999) Kinetic spray coatings. Surf Coat Technol 111(1):62–71
Van Steenkiste TH, Smith JR, Teets RE, Moleski JJ, Gorkiewicz DW (2000) Kinetic spray coating method and apparatus. US Patent 6:139–913
Van Steenkiste TH, Smith JR, Teets RE (2002) Aluminum coatings via kinetic spray with relatively large powder particles. Surf Coat Technol 154(2-3):237–252
Van Steenkiste TH, Kowalsky K, Berghorn C (2015) Particle velocity and particle temperature parameter effects on coating formation. In: Maev R, Leshchynsky V (eds) Book cold gas dynamic spray. CRC Press, pp 220–235
Villafuerte J (2005) Cold spray: a new technology. Weld J 84(5):24–29
Walter JW (1992) Numerical experiments on adiabatic shear band formation in one dimension. Int J Plast 8:657–693
Winston R (ed) (2011) Uhlig’s corrosion handbook, 3rd edn. Wiley, Oxford, London, p 1296
Yandouzi M, Gaydos S, Guo D, Ghelichi R, Jodoin B (2014) Aircraft skin restoration and evaluation. J Therm Spray Tech 23(8):1281–1290
Yu M, Li W, Guo X, Liao H (2013) Impacting behavior of large oxidized copper particles in cold spraying. J Therm Spray Technol 22:433–440
Zhanpeng J (1981) A study of the range of stability of sigma phase in some ternary systems. Scand J Metall 10:279–287
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer International Publishing AG
About this chapter
Cite this chapter
Maev, R.G., Leshchynsky, V. (2018). Low-Pressure Cold Spray (LPCS). In: Cavaliere, P. (eds) Cold-Spray Coatings. Springer, Cham. https://doi.org/10.1007/978-3-319-67183-3_4
Download citation
DOI: https://doi.org/10.1007/978-3-319-67183-3_4
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-67182-6
Online ISBN: 978-3-319-67183-3
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)