Abstract
Waste cooking oil is hard to dispose of and harmful to the environment. Recently, a considerable amount of research has been done to improve the properties of engine oil. In this study, engine oil was blended with waste cooking oil and an oil treatment solution. The blended oil was tested in a tribological wear tester. There are three parameters (rotational speed, loads and ratio of waste cooking oil) was consider in the experiments. Tribology wear and properties of the blended oil were investigated in FESEM. It was found that abrasive wear, adhesive wear, fatigue wear and corrosive wear were introduced during the course of the experiments. Normally, corrosive wear was found to be the main dominant in the tribology wear. It was discovered that 5% addition of waste oil to the engine oil treatment and base lubricant performed better than other oil blends.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Mobarak HM et al (2014) The prospects of biolubricants as alternatives in automotive applications. Renew Sustain Energy Rev 33:34–43
Arumugam S, Sriram G (2012) Effect of bio-lubricant and biodiesel-contaminated lubricant on tribological behavior of cylinder liner-piston ring combination. Tribol Trans 55(4):438–445
Sadaka S, Boateng AA (2009) Pyrolysis and bio-oil. Cooperative Extension Service, University of Arkansas, US Department of Agriculture and county governments cooperating
Ting C-C, Chen C-C (2011) Viscosity and working efficiency analysis of soybean oil based bio-lubricants. Measurement 44(8):1337–1341
Mofijur M et al (2012) Prospects of biodiesel from Jatropha in Malaysia. Renew Sustain Energy Rev 16(7):5007–5020
Shahabuddin M et al (2013) Comparative tribological investigation of bio-lubricant formulated from a non-edible oil source (Jatropha oil). Ind Crops Prod 47:323–330
Cheenkachorn K, Fungtammasan B (2010) Development of engine oil using palm oil as a base stock for four-stroke engines. Energy 35(6):2552–2556
Syahrullail S et al (2011) Experimental evaluation of palm oil as lubricant in cold forward extrusion process. Int J Mech Sci 53(7):549555
Jayed MH et al (2009) Environmental aspects and challenges of oilseed produced biodiesel in Southeast Asia. Renew Sustain Energy Rev 13(9):24522462
Maleque MA, Masjuki HH, Haseeb ASMA (2000) Effect of mechanical factors on tribological properties of palm oil methyl ester blended lubricant. Wear 239(1):117–125
Jayadas NH, Prabhakaran Nair K, Ajithkumar G (2007) Tribological evaluation of coconut oil as an environment-friendly lubricant. Tribol Int 40(2):350–354
Kalam MA, Masjuki HH (2002) Biodiesel from palmoil—an analysis of its properties and potential. Biomass Bioenerg 23(6):471–479
Zeman A et al (1995) Biodegradable lubricants—studies on thermo-oxidation of metalworking and hydraulic fluids by differential scanning calorimetry (DSC). Thermochim Acta 268:9–15
Çakir M, Akçay IH (2014) Frictional behavior between piston ring and cylinder liner in engine condition with application of reciprocating test. Int J Mater Eng Technol 11(1):57
Cesur İ et al (2014) The effects of different fuels on wear between piston ring and cylinder. Adv Mech Eng 2014:1–8
Stachowiak GW, Batchelor AW, Stachowiak GB (2004) 2—Simulation of wear and friction. In: Gwidon AWB, Stachowiak W, Grazyna BS (ed) Tribology series, Elsevier, pp 13–23
Mehta DS, Masood SH, Song WQ (2004) Investigation of wear properties of magnesium and aluminum alloys for automotive applications. J Mater Process Technol 155–156:1526–1531
Holt JM (Tim), T.E.C.Y.H. (1996) Structural alloys handbook. CINDAS/Purdue University, West Lafayette, IN
Boyer HE, Gall TL (1985) Metals handbook. American Society for Metals, Materials Park, OH
Zulkifli NWM et al (2013) Wear prevention characteristics of a palm oil-based TMP (trimethylolpropane) ester as an engine lubricant. Energy 54:167–173
Lee EJ et al (2010) Morphology and toughness of abrasive particles and their effects on the friction and wear of friction materials: a case study with zircon and quartz. Tribol Lett 37(3):637–644
Masjuki HH, Maleque MA (1996) The effect of palm oil diesel fuel contaminated lubricant on sliding wear of cast irons against mild steel. Wear 198(1–2):293299
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer International Publishing AG
About this chapter
Cite this chapter
Sakinah, M.H. et al. (2018). Optimization on Wear Performance of Anti Wear Additive Added Biolubricant. In: Öchsner, A., Altenbach, H. (eds) Improved Performance of Materials. Advanced Structured Materials, vol 72. Springer, Cham. https://doi.org/10.1007/978-3-319-59590-0_1
Download citation
DOI: https://doi.org/10.1007/978-3-319-59590-0_1
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-59589-4
Online ISBN: 978-3-319-59590-0
eBook Packages: EngineeringEngineering (R0)