Abstract
In order to increase the efficiency of explosive comminution, the borehole pressure must be maximized and pressure losses minimized. The majority of these pressure losses occur from premature borehole venting and through weak layers intersecting the borehole. With the use of proper stemming material and amount of stemming these pressure losses can be minimized, increasing the efficiency of explosive comminution. This chapter discusses the key considerations in the choice of stemming materials and methods calculate proper stemming size for different borehole sizes. In addition, the pressure models and methods to calculate stemming depth are discussed for both ideal and nonideal stemming material. Following the stemming design section, the chapter presents methods to improve stemming efficiency and reduce total stemming height including airdecks and stemming plugs. The chapter then addresses the issue of minimal fragmentation in the stemming zone. Practical design guidelines are presented for the use of a stem charge, allowing for breakage in the stemming zone.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Konya C, Walter E (1990) Surface blast design. Englewood Cliffs, New Jersey
Konya C (2015) Rock blasting and overbreak control. Intercontinental Development Inc. Montville, Ohio
Snelling W, Hall C (1912) The effects of Stemming on the efficiency of explosives. Washington D.C
Matthews D (1978) Personnal Communication
Sharma S, Rai P (2015) Investigation of crushed aggregate as stemming material in bench blasting: a case study. Geotech Geo Eng 1449–1463
Kojovic T (2005) Influence of aggregate stemming in blasting on the sag mill performance. Miner Eng: 1398–1404
Cevizci H, Ozkahraman H (2012) The effect of blast hole stemming length to rockpile fragmentation at limestone quarries. Int J Rock Mech Min Sci
Konya C, Otounye F, Skidmore D (1982) Airblast reduction from effective blasthole stemming. In: Proceedings of eighth conference on explosives and blasting technique, pp 145–156
Konya C (1968) Spacing of explosive charges. Dissertation, University of Missouri, Rolla
Konya C, Davis J (1978) The effects of stemming consist on retention in blastholes. In: Proceedings of the fourth conference on explosives and blasting technique, pp 102–112
Davis G (1977) The effects of stemming consist on retention in blastholes. Dissertation, University of West Virginia
Cevizci H (2013) A new stemming application for Blasting. A case study. Mineracao Min 513–519
Eloranta J (1994) Stemming selection for large-diameter blastholes. In: Conference on explosives and blasting technique, pp 255–266
Cevizci H (2012) A newly developed plaster stemming method for blasting. J South Afr inst Min Metall 1071–1078
Otuonye F, Konya C, Skidmore D (1983) Effects of stemming size distribution on explosive charge confinement: a laboratory study. Min Eng 1205–1208
Dobrilovic M, Ester Z, Jankovic B (2005) Measurement in blast hole stem and influence of stemming materials on blasting quality. Rudarsko-geolosko-naftni Zbornik 47–53
Boshoff D, Webber-Youngman R (2011) Testing stemming performance, possible or not? J South Afr Inst Min Metall 871–874
Otuonye F (1981) Effective blasthole stemming. Dissertation, The Ohio State University
Qinan W (1912) High explosives. London, United Kingdom
Cooper P (1996) Explosive engineering. New York
Cook M (1947) An Equation of State for Gases at Extremely High Pressures and Temperatures from the Hydrodynamic Theory of Detonation. Journal of Chemical Physics: 518-524
Cook M (1974) The Science of Industrial Explosives. Albequerque, New Mexico
Johansson C, Persson P (1970) Detonics of High Explosives. New York, New York
Konya A, Konya C (2017) Precision presplitting—explosive load variations with spacing. In: Proceedings of the international society of explosive engineers, pp 553–562
Kutter H, Fairhust C (1971) On the fracture process in blasting. Int J Rock Mech Min Sci 181–202
Worsey P (1981) Geotechnical factors affecting the application of pre-split blasting to rock slopes. Dissertation, University of Newcastle upon Tyne
Johnsson G, Hofmeister W (1960) The influence of stemming on the efficiency of blasting using 36MM-shot-holes. In: International symposium on mining research, pp 91–102
Worsey P (1990) Experimental data indicating a direct link between the rate of stemming ejection and the degree of rock face movement in bench blasting. In: Proceedings of the conference on explosive and blasting procedure, pp 83–95
Perry R, Green D (2007) Perry’s chemical engineers’ handbook. China
Cook M (1971) The science of high explosives. Huntington
Furnas C (1929) Flow of gases through beds of broken solids. Washington D.C
Foldesi J (1974) Nyujtott Toltetekkel Torteno Kozetjovesztes Robbantastechnika Parametereinek Neghatarozasa Kulfejtesben. Doktori Ertekezes Miskolc
Outuonye F (1978) Modeling the behavior of blasthole stemming. Dissertation, University of West Virginia
Langfors U, Kihlstrom B (1973) The modern technique of rock blasting. New York, New York
Knopp J (2000) Stemming ejection and burden movements of small borehole blasts. In: Proceedings of the conference on explosives and blasting technique, pp 1–10
Sazid M, Saharan M, Singh T (2012) Effective explosive energy utilization for engineering blasting—initial results of an inventive stemming plug. Harmonising Rock Engineering and the Environment, pp 1265–1268
Jenkins S, Floyd J (2000) Stemming enhancement tests. In: Proceedings of the conference on explosive and blasting technique, pp 191–204
Worsey P (1990) Stemming ejection comparison of conventional stemming and stemming incorporating blast control plugs for increasing explosion energy use. Frablast 1990:361–367
Carr B (2000) New stem plug devices and applications. Stemtite LLC BAI workshop
Correa C, Navarrete M (2004) Assessment of stemming plug plastic elements to improve blasting gases confinement in escondida. Explo 2004:95–100
Choudhary B, Rai P (2013) Stemming plug and its effect on fragmentation and Muckpile shape parameters. Int J Min Mineral Eng 296–311
Varistem (2004) Vari-stem blasthole plugs improve blasting patterns. Min Eng 31
Jhanwar J, Jethwa J, Reddy A (2000) Influence of air-deck blasting on fragmentation in jointed rocks in an open-pit manganese mine. Eng Geol 13–29
Sazid M, Saharan M, Singh T (2016) Enhancement of the explosive energy utilization with the application of new stemming contrivance. Int J Innovative Sci Mod Eng 1–5
Wilkins M, Worsey P (1998) Stemming Technique for loading Angled Hoels charged with ANFO. In: Proceedings of the conference on explosive and blasting technique, pp 159–169
Konya A, Konya C (2016) Stemming charge. Acad Blasting Explos Technol
Konya C, Walter E (1988) Blasthole timing controls vibration, air blast, and flyrock. Coal Min
Konya C (1987) Accurate blasthole timing reduces blasting cost. Mine Quarry
Rodgers J, Lee R, Whitaker K (2003) The origins and effects of inter-deck pressure in decked blasts. In: Proceedings of the conference on explosive and blasting technique
Akhaven J (2011) The chemistry of explosives. Cambridge
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer International Publishing AG
About this chapter
Cite this chapter
Konya, C.J., Konya, A. (2018). Effect of Hole Stemming Practices on Energy Efficiency of Comminution. In: Awuah-Offei, K. (eds) Energy Efficiency in the Minerals Industry. Green Energy and Technology. Springer, Cham. https://doi.org/10.1007/978-3-319-54199-0_3
Download citation
DOI: https://doi.org/10.1007/978-3-319-54199-0_3
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-54198-3
Online ISBN: 978-3-319-54199-0
eBook Packages: EnergyEnergy (R0)