Abstract
In this chapter we review the major types of atomization process configurations: free-fall gas atomization with an unconfined melt stream and close-coupled gas atomization with controlled melt introduction to an energetic gas flow. Studies will be reported of several types of devices, termed atomization nozzles, which are used to perform two-fluid atomization processes that involve the disintegration of a molten metal by interaction with a high velocity atomization gas. The resulting atomization process is a complex physical phenomena consisting of stages that start with melt stream pre-filming and distribution to the primary atomization zone, where melt sheets or ligaments form and initial droplet breakup (primary atomization) occurs by the interaction of a high density, hot melt with a high velocity (high kinetic energy, but low temperature) atomization gas, typically. Primary atomization is followed in the near-field region by secondary breakup, if a high enough gas velocity and sufficient mismatch velocity with the melt fragments are maintained to cause significant production of further droplets. Thus, the atomization processes described in this chapter essentially involve momentum and heat exchange between gas and melt, while other chapters will discuss the subsequent processes of droplet solidification, droplet-droplet or particle-droplet collisions and other spray phenomena that are important to spray deposition. Primarily, this chapter will deal with our state of understanding of melt breakup physics and the various types of gas atomization nozzles that can be used to generate an atomized molten metal spray.
This is a preview of subscription content, log in via an institution.
Buying options
Tax calculation will be finalised at checkout
Purchases are for personal use only
Learn about institutional subscriptionsReferences
Anderson, I., Terpstra, R., & Figliola, R. (2005). Visualization of enhanced primary atomization for powder size control. In Advances in powder metallurgy and particulate materials (pp. 1–17). Princeton, NJ: Metal Powder Industries Federation.
McHugh, K. M., Lin, Y., Zhou, Y., Johnson, S., Delplanque, J.-P., & Javernia, E. (2008). Microstructure evolution during spray rolling and heat treatment of 2124 Al. Materials Science and Engineering, 477, 26–34.
Fritsching, U. (2004). Spray simulation: Modeling and numerical simulation of sprayforming metals. Cambridge: Cambridge University Press.
Yule, A., & Dunkley, J. (1994). Atomization of melts. Oxford: Clarendon Press.
Fritsching, U., & Bauckhage, K. (1992). Investigations on the atomization of molten metals: The coaxial jet and the gas flow in the nozzle near field. PHOENICS Journal of Computational Fluid Dynamics, 1, 5.
Markus, S., Fritsching, U., & Bauckhage, K. (2002). Jet break up of liquid metals in twin fluid atomization. Materials Science and Engineering: A, 326, 122–133.
Heck, U. (1998). Zur Zerstäubung in Freifalldüsen. Düsseldorf: VDI Verlag.
Lohner, H., Czisch, C., & Fritsching, U. (2003). Impact of gas nozzle arrangement on the flow field of a twin fluid atomizer with external mixing. In International conference on liquid atomization and spray systems. Sorrento, Italy.
Uhlenwinkel, V., Fritsching, U., Bauckhage, K., Urlau U. (1990). Strömungsuntersuchungen im Düsennahbereich einer Zweistoffdüse - Modelluntersuchungen für die Zerstäubung von Metallschmelzen, Chemie Ingenieur Technik – CIT Volume 62, Issue 3, S. 228-229
Czisch, C., Lohner, H., & Fritsching, U. (2004). Einfluss der Gasdüsenanordnung auf den Desintegationsvorgang und das Zerstäubungsergebnis bei der Zweistoff-Zerstäubung. Chemie-Ingenieur-Technik, 76, 754–757.
Heck, U., Fritsching, U., & Bauckhage, K. (2000). Gas-flow effects on twin-fluid atomization of liquid metals. Atomization and Sprays, 10, 25–46.
Wille, R., & Fernholz, H. (1965). Report on the first European mechanics colloquium on the coanda effect. Journal of Fluid Mechanics, 23, 801–819.
Czisch, C., & Fritsching, U. (2008). Atomizer design for viscous-melt atomization. Materials Science and Engineering, 477(1–2), 21–25.
Schwenck, D., Ellendt, N., & Uhlenwinkel, V. (2014). Gas recirculation affects powder quality. In World confress on powder metallurgy and particulate materials (PM2014). Orlando, Florida.
Lawley, A. (1992). Atomization: The production of metal powders (pp. 102–107). Princeton, NJ: MPIF.
Ting, J., Peretti, M. W., & Eisen, W. B. (2000). Control of fine powder production and melt flow rate using gas daynamics. Advances in Powder Metallurgy and Particulate Materials, 2, 27–40.
Mates, S. P., Ridder, S. D., & Biancaniello, F. S. (2000). Comparison of supersonic length and dynamic pressure characteristics of discrete–jet and annular close–coupled nozzles used to produce fine metal powders. In Liquid metal atomization: Fundamentals and practice, TMS annual meeting and symposium (pp. 71–81).
Ting, J., & Anderson, I. E. (2004). A computational fluid dynamics (CFD) investigation of the wake closure phenomenon. Materials Science and Engineering, A379, 264–276.
Anderson, I. E., Terpstra, R. L., Cronin, J. A., & Figliola, R. S. (2006). Verification of melt property and closed wake effects on controlled close-coupled gas atomization processes. In Advances in powder metallurgy and particulate materials (pp. 1–16).
Unal, A. (1987). Effects of processing variables on particle size in gas atomization of rapidly solidified aluminium powders. Materials Science and Technology, 3, 1029–1039.
Brandes, E., & Brook, G. (1992). Smithells metals reference book (7th ed.). Oxford: Butterworth Heinemann.
Ingebo, R. D. (1980). Atomizing characteristics of swirl blast fuel injectors. NASA Technical Memorandum 79297. Cleveland, OH: Lewis Research Centre.
Rieken, J., Heidloff, A., & Anderson, I. (2013). Moving towards improved ultra-fine powder production for precursor ODS Fe-based alloys, compiled by D. Christopherson & R. M. Gasior, metal powder. Advances in Powder Metallurgy and Particulate Materials, 2, 11–22.
Anderson, I., Figliola, R., & Morton, H. (1991). Flow mechanisms in high pressure atomization. Materials Science and Engineering, 148, 101–114.
Mullis, A. M., Adkins, N. J., Aslam, Z., McCarthy, I., & Cochrane, R. F. (2008). Close-coupled gas atomization: High-frame rate analysis of spray-cone geometry. International Journal of Powder Metallurgy, 44, 55–64.
Mullis, A. M., McCarthy, I., Cochrane, R., & N. J. Adkins. (2016). Investigation of the pulsation phenomenon in close-coupled atomization, Advanced in powder metallurgy and particulate materials. Princeton, NJ: Metal Powder Industries Federation.
Lefebvre. (1989). Atomization and sprays. New York, NY: Hemisphere.
Anderson, I., Terpstra, L., & Rau, S. (2001). SFB-spray forming kolloquium. In Band 5 (pp. 1–16). Norderstedt: Books on Demand GmbH.
Bauckhage, K., & Fritsching, U. (2000). In K. Cooper, I. Anderson, S. Ridder, & F. Biancaniello (Eds.), Liquid metal atomization: Fundamentals and practice (pp. 23–36). Warrendale, PA: TMS.
Lawley, A. (2000). In I. Anderson & K. P. Cooper (Eds.), Liquid metal atomization: Fundamentals and practice. Warrendale, PA: TMS.
Dunkley, J., & Sheikhaliev, S. (1995). Single fluid atomization of liquid metals. In Proceedings of the international conference on powder metallurgy and particulate materials (Vol. 1, pp. 79–87). Seattle, USA.
Achelis, L. (2009). Kombinierte Drall-Druck-Gaszerstäubung von Metallschmelzen. Aachen: Shaker Verlag.
Uhlenwinkel, V. (2002). Patent Nr. 10237213
Lagutkin, S. (2003). Development of technology and equipment for metal powder production by centrifugal-gas atomization of melt. Ekaterinburg: Ural Department of Academy of Sciences.
Lagutkin, S., Achelis, L., Sheikhaliev, S., Uhlenwinkel, V., & Srivastava, V. (2004). Atomization process for metal powder. Materials Science and Engineering: A, 383, 1–6.
Achelis, L., & Uhlenwinkel, V. (2007). Characterisation of metal powders generated by a pressure-gas-atomize. Materials Science and Engineering A, 477(1–2), 15–20.
Achelis, L., Uhlenwinkel, V., Lagutkin, S., & Sheikhaliev, S. (2007). Atomization using a pressure-gas-atomizer. Materials Science Forum, 534–536, 13–16.
Achelis, L., Sulatycki, K., Uhlenwinkel, V., & Mädler, L. (2010). Spray angle and particle size in the pressure gas atomization of tin and tin-copper alloys. In Proceeding of the international conference on powder metallurgy. Florence, Italy.
Achelis, L., Uhlenwinkel, V., Sulatycki, K., & Mädler, L. (2010). New approach to generate composite particles. In Proceeding of the international conference on powder metallurgy and particulate materials (pp. 1–11). Florida, USA.
Fraser, R., & Eisenklam, P. (1953). Research into the performance of atomization of liquids. Imperial ChemEngSoc, 7, 52.
Li, X. (2014). Modeling and simulation of the gas-atomization process of metal melts for metal-matrix-composite production. Aachen: Shaker Verlag.
Lohner, H. (2002). Zerstäuben von Mineralschmelzen mit Heißgas. PhD. thesis, University Bremen.
Czisch, C., Lohner, H., Fritsching, U., Bauckhage, K., & Edlinger, A. (2003). Atomisation process for metal powder. In K. Bauckhage, U. Fritsching, J. Ziesenis, A. Uhlenwinkel, A. Leatham (Eds.), Proceedings on Spray Deposition and Melt Atomization Conference SDMA 2003, Bremen, 22–25 June 2003.
Strauss, J.T. (1999). Hotter gas increases atomization efficiency. Metal Powder Report, 11, 24–28.
Dunkley J.J. (2001). In 2001 International Conference on Powder Metallurgy and Particulate Materials PM2TEC 01, 2-29-2-35, 2001, Metal Powder Industries Federation, Princeton, USA.
Fraser, R.P., Dombrowski, N., & Routley, J.H. (1962). Chemical Engineering Science, 18, 339–353.
Pickering, S.J., Hay, N., Roylance, T.F., & Thomas, G.H. (1985). Ironmaking and Steelmaking, 12(1).
Campanile, F., & Azzopardi, B.J. (2003). In Cavaliere, A. (Ed.), CD-ROM Proceedings of International Conference on Liquid Atomization and Spray Systems ICLASS 2003, Sorrento, Italy, 13-17.07.2003, ILASS-Europe.
Fritsching, U., & Bauckhage, K. (2006). Sprayforming of metals. In Ullmann’s encyclopedia of industrial chemistry (Vol. 7). Weinheim: Wiley VCH.
Lohner, H., Czisch, C., Schreckenberg, P., Fritsching, U., & Bauckhage, K. (2005). Atomization of viscous melts. Atomization and Sprays, 15(2), 169–180.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2017 Springer International Publishing AG
About this chapter
Cite this chapter
Anderson, I.E., Achelis, L. (2017). Two Fluid Atomization Fundamentals. In: Henein, H., Uhlenwinkel, V., Fritsching, U. (eds) Metal Sprays and Spray Deposition. Springer, Cham. https://doi.org/10.1007/978-3-319-52689-8_3
Download citation
DOI: https://doi.org/10.1007/978-3-319-52689-8_3
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-52687-4
Online ISBN: 978-3-319-52689-8
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)