Abstract
The fatigue behavior of the Thixomolded® magnesium alloy AZ91D has been examined using ultrasonic fatigue testing techniques at frequencies of approximately 20 kHz and for lifetimes as long as 109 cycles. An apparent endurance limit of approximately 65–70 MPa is observed. Comparison with the fatigue behavior of AZ91 produced by conventional die casting indicates that the Thixomolded® material has an endurance limit substantially higher than that of die cast material. This is attributed primarily to reduced porosity associated with the thixotropic processing technique. Fractographic analyses indicate that fatigue cracks leading to failure initiate at internal porosity in approximately 75% of tests and at the as-molded surface in the remainder of tests. Fractographic studies indicate that, in general, longer fatigue lifetimes are associated with smaller fracture initiation sites. It was also observed that a bimodal distribution of fatigue lives occurred, especially at lower stresses. This was analyzed using cumulative distribution functions, which confirmed the existence of dual failure populations.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
References
A.A. Luo, “Materials Comparison and Potential Applications of Magnesium in Automobiles,” Magnesium Technology 2000, ed. H.I. Kaplan et. al., (Warrendale PA: The Minerals, Metals and Materials Society, 2000), 89–97.
L.E. Willertz, “Ultrasonic Fatigue,” Int. Mat. Rev., 25 (2) (1980), 65–78.
ASM: ASM Handbook, Vol. 8 (ASM International, Materials Park, OH, 1985).
S.E. Stanzl-Tschegg, “Fracture Mechanisms and Fracture Mechanics at Ultrasonic Frequencies,” Fatigue Fract. Engng. Mater. Struct., 22 (1999), 567–579.
H. Mayer, “Fatigue Crack Growth and Threshold Measurements at Very High Frequencies,” Int. Mat. Rev., 44 (1) (1999), 1–34.
H. Mayer et. al., “Influence of Loading Frequency on the High Cycle Fatigue Properties of AlZnMgCu1.5 Aluminum Alloy,” Mater. Sci. Engng., A314 (2001), 48–54.
S.E. Stanzl-Tschegg and H. Mayer, “Fatigue and Fatigue Crack Growth of Aluminum Alloys at Very High Numbers of Cycles,” Int. J. Fatigue, 23 (2001), S231-S237.
M.J. Caton et. al., “Demonstration of an Endurance Limit in Cast 319 Aluminum,” Metall. Mater. Trans. A, 34A (2003), 33–41.
Q.Y. Wang et. al., “Gigacycle Fatigue of Ferrous Alloys,” Fatigue Fract. Engng. Mater. Struct., 22 (1999), 667–672.
S.A. Padula II et. al., “High Frequency Fatigue Crack Propagation Behavior of a Nickel-Base Turbine Disk Alloy,” Int. J. Fatigue, 21 (1999), 725–731.
R.O. Ritchie et. al., “Thresholds for High-Cycle Fatigue in a Turbine Engine Ti-6Al-4V Alloy,” Int. J. Fatigue, 21 (1999), 653–662.
M. Papakyriacou et. al., “Influence of Loading Frequency on High Cycle Fatigue Properties of B.C.C. and H.C.P. Metals,” Mater. Sci. Engng., A308 (2001), 143–152.
H. Mayer et. al, “Influence of Porosity on the Fatigue Limit of Die Cast Magnesium and Aluminum Alloys,” Int. J. Fatigue, 25 (2003), 245–256.
A. Bag and W. Zhou, “Tensile and Fatigue Behavior of AZ91D Magnesium Alloy,” J. Mater. Sci. Lett., 20 (2001), 457–459.
D.L. Goodenberger and R.I. Stephens, “Fatigue of AZ91E-T6 Cast Magnesium Alloy,” J. Engng. Mater. Tech., 115 (1993), 391–397.
F. Czerwinski et. al., “Correlating the Micro structure and Tensile Properties of a Thixomolded AZ91D Magnesium Alloy,” Acta Mater., 49 (2001), 1225–1235.
F. Czerwinski, “Size Evolution of the Unmelted Phase During Injection Molding of Semisolid Magnesium Alloys,” Scripta Mater., 48 (2003), 327–331.
A. Balasundaram and A.M. Gokhale, “Quantitative Characterization of Spatial Arrangement of Shrinkage and Gas (air) Pores in Cast Magnesium Alloys,” Mater. Charact., 46 (2001), 419–426.
Y. Murakami and M. Endo, “The √Area Parameter Model for Small Defects and Nonmetallic Inclusions in Fatigue Strength: Experimental Evidences and Applications,” Theoretical Concepts and Numerical Analysis of Fatigue, (Birmingham UK: 1992), 51–71.
S.K. Jha et. al., “Dual Fatigue Failure Modes in Ti-6Al- 2Sn-4Zr-6Mo and Consequences on Probabilistic Life Prediction,” Scripta Mater., 48 (2003), 1637–1642.
Author information
Authors and Affiliations
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2016 The Minerals, Metals & Materials Society
About this chapter
Cite this chapter
Moore, A.R., Torbet, C.J., Shyam, A., Jones, J.W., Walukas, D.M., Decker, R.F. (2016). Fatigue Behavior of Thixomolded® Magnesium AZ91D Using Ultrasonic Techniques. In: Mathaudhu, S.N., Luo, A.A., Neelameggham, N.R., Nyberg, E.A., Sillekens, W.H. (eds) Essential Readings in Magnesium Technology. Springer, Cham. https://doi.org/10.1007/978-3-319-48099-2_38
Download citation
DOI: https://doi.org/10.1007/978-3-319-48099-2_38
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-48588-1
Online ISBN: 978-3-319-48099-2
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)